Thanks for the clear video instructions! Judging by the colour of the water I probably should have done this a while ago...
@PacMoto
Жыл бұрын
Yeah, right! I was a little surprised the first time I did it too. Thanks for the comment.
@MarkBedford-b2f
18 күн бұрын
I appreciate the video. After washing and rinsing, I used a salad spinner to remove the excess water from the liner pads, and it worked flawlessly.
@PacMoto
17 күн бұрын
The salad spinner is brilliant!
@richardgrumbine4867
Жыл бұрын
Thanks! Nice Job! I am about to re-install my pads but I took them out many moons ago… so was not sure I remember how to do those two straps that go from the back of the helmet… your instructions were very clear… though my seem to be corroded closed… DOH!
@PacMoto
Жыл бұрын
Thanks for the feedback. Maybe a little wire brush and WD40 will help you open the zippers.
@DonlineUK
3 ай бұрын
Thanks for this video - most helpful! 😀 Fiddly job but your vid made the task much easier :0). Nice fresh C3 Pro lid, ready for the road again. 🏍 Thanks & Blessings, D
@PacMoto
3 ай бұрын
Enjoy the ride!
@OurDigitalClassRoom
6 ай бұрын
G8 video - thanks. My C3 Pro is old. Did the inner today following your instructions. Only issue for me is that the zippers are seriously corroded and non operative. So just had to remove the liner from the cheek pads and wash that. I wish I’d known about this sooner. My bad. Anyway - grateful for the steer from your good self.
@PacMoto
6 ай бұрын
Thanks for your comment. I wonder if some lubricant would free up the zipper?
@BogdanMarcu
2 жыл бұрын
You saved my helmet. I would never found those zippers for the straps :)) Thanks!
@PacMoto
2 жыл бұрын
I struggled and struggled the first time I tried to wash the helmet liner! Thanks for the comment.
@brrrr16
4 ай бұрын
I looked for this video to see how to remove the chin part…no luck. The rest is ok. Good job sir
@PacMoto
4 ай бұрын
I don’t think I’ve ever removed the chin part…
@paulbuschman8318
2 жыл бұрын
Thanks! Didn't realize it was this easy to wash!
@PacMoto
2 жыл бұрын
Now you can have a clean helmet!
@ItchyBones
9 ай бұрын
Thanks for this. Just bought a C4 basic and there is nothing in the manual about removing the liner, which I need to do at least partially to install my Cardo system like yours was. One thing that is bothering me is those two straps at the back on mine don't appear to be attached to anything, which seems a bit weird. Yours appear to be stuck down pretty good.
@PacMoto
9 ай бұрын
I think those two straps are supposed to be screwed into the helmet. It may be a manufacturing defect.
@ItchyBones
9 ай бұрын
@@PacMoto oh thanks for that. I better contact the seller
@rs8197-dms
Жыл бұрын
This was very informative, but I note that you didn't remove the chin padding - is this because it can't be done? Surely not?
@PacMoto
7 ай бұрын
Correct, 8Nm
@dipling.pitzler7650
2 жыл бұрын
I can confirm that its the same process with the C3 Pro ( the one with the double intake on the top of the helmet). One question though: What to do if the collar consists of the model with the built in control knobs for the Cardo communication system ? Dry clean?
@PacMoto
2 жыл бұрын
Thank you for the confirmation. The SRC system replaces the original collar. I’d suggest that you detach the SRC collar and re-install the original one (hopefully you saved it!). Remember to be careful with the pins.
@fergallawlor1353
11 ай бұрын
Great video. The zip had me puzzled 😂
@PacMoto
11 ай бұрын
Yeah, it’s obvious once you know it’s there!
@fergallawlor1353
11 ай бұрын
@@PacMoto yes newbie biker here feeling like a dumbass lol 😆
@evrenuzun5199
Жыл бұрын
thank for your great info... it's save my helmet... good job
@PacMoto
Жыл бұрын
Thanks for the comment!
@DumbledoreMcCracken
Жыл бұрын
Thank you! Zippers!
@PacMoto
Жыл бұрын
Secret zippers!
@_skud
Жыл бұрын
Thanks for the video. very helpful
@PacMoto
Жыл бұрын
You’re welcome. Thanks for watching.
@Thomas998822
2 жыл бұрын
How did the liner hold up? The label actually says just wipe it off and to not soak it
@PacMoto
2 жыл бұрын
I gently hand wash the liner once a year, so this is the 5th time. No issue at all.
@Jandejongjong
2 жыл бұрын
How do I remove the chin part? I can take out the small part. But how do I do the rest?!
@PacMoto
2 жыл бұрын
Thanks for the comment. The trick is to find the zipper and open it. You can then feed the straps through to fully remove the liner. Feel free to send me a photo of the issue so I can better understand where you are working. Send to info@pacmototours.com.
@robans
Жыл бұрын
Can I put it in my washer on 15' cold programe?
@PacMoto
Жыл бұрын
I think it is best to hand wash the liner.
@christopheicher2832
11 ай бұрын
I have washed the inner cushions on a 30‘ C program with a mild wool detergent. Came out perfect. The collar I have washed by hand.
@PacMoto
11 ай бұрын
@christopheicher2832 Excellent!
@JohnBerry-lx7pf
Жыл бұрын
every thing is black can not see anything need more light on the procedure to be help full thanks for the try
Пікірлер: 42