You explained it very very good. This is very helpful. Thank you so much for this video. 👍
@green-crocs-fixes1520
2 ай бұрын
Thanks Trainer 😎
@andreabygrave7622
Жыл бұрын
Many thanks. A successful bearing change on my machine, which is the exact same one as in the video. I'm glad attitudes are changing to a less wsteful society now. If the fix hadn't worked for any reason, I would have bought an Ebac machine. English-made and fully repairable.
@green-crocs-fixes1520
Жыл бұрын
Thanks Andrea, and I totally agree with you regarding a wasteful society. When you see the videos on KZitem from third world countries where they have no choice but to improvise a repair (and they are successful with it too) here we are urged to discard and replace. and with manufacturers designing units this way to discourage your average DIY enthusiast, not good @ all. Regards.
@sparkspark8309
6 жыл бұрын
well done on the fix. stopping these robbing companies from making me throw it away
@green-crocs-fixes1520
6 жыл бұрын
Hi Spark, I agree, had already brought a new machine to replace the broken one. Just had to make a statement with this one rather than just putting it out for the rag-n-bone man, Regards.
@maidenstrat1
4 жыл бұрын
I was told by whirlpool that because the tub was sealed you could never get a new bearing etc and the tub would cost me around £200, which is very uneconomical. I sourced a bearing manufacturer gave them the bearing number..... £6.00 + VAT...Result. Always quote the bearing number and you can get a new bearing cheap as chips....
@RogerkRogerk
4 жыл бұрын
Brilliant Just a few more tips on how to do this Job which takes time but is not difficult really. Watch all the Videos on this first As you dismantle the washing machine take video or photos at each stage before you unscrew things, disconnect wires or unbolt things, that way you won't be struggling when it comes to re assembling the machine. more is better than less, trust me. Before you cut the drum mark the drum with a Sharpie pen in several places this will aid re assembly, and drill 4mm holes at about 100mm (4inch) centres all round the lip where you are going to cut, you can buy a long, 4mm drill bit, 120mm long from Screwfix (about £3.00 for 2) while you are there buy the 4mm Stainless lock nuts (£3.00) and 30mm long Bolts (also about £3.00) You might need to buy some Vernier Calipers to accurately measure the old bearing sizes, more on this later. When you are drilling the holes test the first one with a nut and bolt to make certain you can get it in and do it up you when you come to re assemble, this will prevent you from drilling in the wrong vertical plane. Cutting the Drum. I opted for using a hacksaw, which will cut all the way round the drum, I have power tools but you are in better control with a hand tool. It took just under an hour, quick tea break included. You will need a waterproof sealant when you put the drum back together. I used Aqua Mate Sealant.(£5.00) Knock out the outer bearing first, so from the inside out, using a metal drift, it takes a bit of whacking before it comes out. Then from the outside knock out the inner bearing, the water seal comes out with the bearing when you do this. Now you have your bearings and seal out measure them with a good mm rule or the Verner capilers, you need, inner diameter, outer diameter and thickness in each case. I then ordered them from Wych Bearings (about £20.00 the lot)on line. I did this job in the morning about 11.00 and so was able to just get them the next day just using standard first class post. There is a helpline if you are not sure what you want. I put the new bearings in the freezer for a couple of hours (Metal contracts in cold) and kept the drum in the sun (Metal expands in heat) to make it easier to knock them in .follow the videos for this but use wood blocks because any metal on metal blows will damage your new bearings. Use loads of sealant on the drum before you put the two bits together. Line it all up and put in the nuts and bolts you have plenty of time to do them up tight. I let my drum and sealant cure for 24 hours after, but it can be done faster I think. Then just re assemble it all. Hope you took enough photoes......!!!
@green-crocs-fixes1520
4 жыл бұрын
Thanx
@paulbrowne5049
Жыл бұрын
You are a braver man than me. Good job
@Woodfamily160
2 жыл бұрын
This is a great video. I have exactly the same problem. Many thanks for making this. With appreciation. Andy
@green-crocs-fixes1520
2 жыл бұрын
Thanks Andy, Appreciate the appreciation. Regards.
@Woodfamily160
2 жыл бұрын
Hi. Do you have the bearing dimensions and the company that you ordered them from. That would be really helpful. I took my machine tub out the day before going in for a heart operation. I can't finish the job until I feel fitter but it would be great if I could order the bearings and have them ready.
@green-crocs-fixes1520
2 жыл бұрын
@@Woodfamily160 Hi Andy, there are no Bearings or Seal listed for an Eco or Sealed Tub as they are not designed to be replaced. You have to measure the old ones once you have removed them then request the sizes from an online Bearings supplier. Get well soon M8.
@spencerbrooks5311
6 жыл бұрын
Thank you for the time and effort you have put in to helping others. I'm disgusted my Indesit has only lasted 2 years and they haven't even made the poor quality bearings more easily replaceable. I feel like giving this a go because I refuse to pay them £225 for a new drum!!
@green-crocs-fixes1520
6 жыл бұрын
Hi Spencer, Thanx M8. I had already replaced our machine after realising that it had a Sealed Tub. This is the second time I am doing one of these as I done my first one two years ago kzitem.info/news/bejne/qWqn35evcqeggXo just thought I would do a more detailed version which should hopefully answer a lot of previously asked questions... and to make a statement to Hotpoint, Indezit, Whirlpool.... ect. Kindest Regards.
@Martindyna
3 жыл бұрын
Exactly ! Nice to get around a company's design in poor build quality ethos (that they hope will make them extra profit on spares).
@ata2k6
5 жыл бұрын
Great job, man! My suggestions for this operation : Door seal removed from chassis, not from tub (much easier to put back after), remove the water level sensor from chassis, otherwise you can damage it when extracting the tub; - never put down new bearings to the ground, dirt can get inside the bearing, reducing life. Also, first clean out the place of the bearings inside the drum, until you seat back the new bearings. The bronze ring which comes in contact with the seal must be examined, it could be worned out, so the new shaft seal won't seal enough and water could leak inside, if it's worn out, you need to replace it either put a speedy sleeve over, otherwise in a few months the bearings gonna fail again. The secret tip - older washing machine had a small hole in the tub, between the seal and the internal bearing, for the purpose of draining out the small amount of water which can leak in through the seal. This hole is not present on current tubs, but you can make it, with a 4 -6mm drill, which point from the inside to out, in the heating element's direction. This can add a few extra years life to bearings, since these are failing due to water which leaks to the bearing. Also - we use red silicone, which isn't as harmful, and also resistant to hot water and chemicals, we use 5*25mm stainless Allen screws with washers, they are easier to mount. And put first 4 screws to guide the two halves of tub on joining, without tghtening, and after 24h put the rest and tighten.
@ata2k6
5 жыл бұрын
Also, keep in mind, that cutting the tub you will loose 1 - 1.5mm from the tub's dephts, so you must fill up the cutting surface at least this amount of glue, otherwise the drum can touch the door seal (not the case of Indesit, since the drum is about 5mm back from the rubber, but AEG - Electrolux machines got smaller gap.)
@honich-eriker
4 жыл бұрын
Regarding the condensate drain hole: Did I understand this correctly? Possible condensate should drain off to the inner tub’s external?
@mrvlhs
4 жыл бұрын
This is a great reply. Do you have any tips for figuring out what bearings to purchase before opening the machine apart?
@green-crocs-fixes1520
4 жыл бұрын
Thanx
@green-crocs-fixes1520
4 жыл бұрын
Thanx
@gu1tar3rich31
5 жыл бұрын
Great vid ,half way there with mine . Got the bearings/seal from that well known auction site but was unsure about the seal as it was different from the original, seeing this vid i see it does fit . Thanks for sharing . Got to stick it back together so fingers crossed no leaks . Cheers
@green-crocs-fixes1520
5 жыл бұрын
Hi Rich, Well done M8, hope all goes well. Thanx.
@mrvlhs
4 жыл бұрын
Can I ask how did you figure out what bearings to get?
@beautifulsmall
4 жыл бұрын
Mines working great 3 months after fixing it by drill, cut, sealant and re bolting. the bearings were a (4 hours of pain) to remove, but you get what you want. be encouraged to try.
@green-crocs-fixes1520
4 жыл бұрын
Could not have said it better Beautiful Small. Nothing ventured and all that. Well Done.
@rootsdat
2 жыл бұрын
What sealant is best ?
@nightstrangler
6 жыл бұрын
Excellent video.
@green-crocs-fixes1520
6 жыл бұрын
nightstrangler Hey thanx Strangler.
@RichDavey
3 жыл бұрын
Brilliant video. Well explained. Crucial bits like drilling before splitting. On with mine now 👍😊
@green-crocs-fixes1520
3 жыл бұрын
Thanks Rich, good luck and all the best with yours. Regards.
@RichDavey
3 жыл бұрын
@@green-crocs-fixes1520 subscribed as it looks like you are to mending rather than throwing away. Good on you 👍😊
@TheGazLab
6 ай бұрын
why cant these manufacturers make things to be repaired at least once?!. cheers for the video I need to adventure inside my growling whirlpool :-) gaz
@green-crocs-fixes1520
6 ай бұрын
Thanks Gaz, totally agree, your expected to have a spare £300+ in your back pocket for a new one, then send your old unit to Landfill... I think ! 😀.
@jwoodard621
4 жыл бұрын
We're just doing ours thankyou so much for this video and well explained
@green-crocs-fixes1520
4 жыл бұрын
Thanks Jackie, and all the best with your project.
@jwoodard621
4 жыл бұрын
Hi there were trying to find the bearings for a 9kg drum and was told we had to buy a whole new machine can you help us please thankyou
@green-crocs-fixes1520
3 жыл бұрын
@@jwoodard621 Sorry Jackie, only just seen this this 10 months on but... I ordered the Bearings and Seal after I removed and measured the old ones, then
@paulbrowne5049
Жыл бұрын
Wow, found this video after my indesit washing machine's bearings failed and thought I'd try doing the job myself. Whilst I admire your skills I think this particular job is beyond mine unfortunately.😢
@green-crocs-fixes1520
Жыл бұрын
Thanks Paul, flattered actually. Yes there was a lot involved in this process but had to perceiver. Pleased with the result though. We can only do what we can only do 😁. Regards.
@gilesviney7631
5 жыл бұрын
Well done ! Excellent .. I'm having fun doing mine, knowing it's possible. Thank you.
@gilesviney7631
5 жыл бұрын
Got the drum out ok, does anyone have the outer dimensions of the bearings ? Or do the inner dimensions automatically set the outer dimensions ? Many thanks
@green-crocs-fixes1520
5 жыл бұрын
Hi Giles, You have to measure the old Bearings radius, diameter and thickness, the seal also and then request these sizes from an online Bearings seller as there is no standard sizes. Regards.
@gilesviney7631
5 жыл бұрын
@@green-crocs-fixes1520 Thanks for the reply. Yes, I was hoping to measure compared to yours ... For example I've measured 64 OD X 30 ID. If they are the same as yours , i would be able to compare to you're order (I was going to ask that too...you're eBay supplier ) :) I'm enjoying this process, so happy to continue. Many thanks Giles
@1Mattza
7 ай бұрын
Hi great video and well explained but the seal you replaced at 13:33 is in the wrong way around!! thanks again for the video though 👍
@green-crocs-fixes1520
7 ай бұрын
Thanks Matt, the replacement Seal is different to the original but it is in correctly. Not possible to fit it the other way. Regards.
@katefergusnicoll2030
4 жыл бұрын
Great video - total respect to anyone who can do this. Worried about disappearance of Green Crocs from 8'40" to 16'42" :)
@green-crocs-fixes1520
4 жыл бұрын
Kate & Fergus Nicoll Thanx Kate and Fergus, This was due to Health & Safety issues. 😎
@whelan312631
3 жыл бұрын
Great video very informative
@green-crocs-fixes1520
3 жыл бұрын
Thanks you very very Whelan 😀
@confucious100
4 жыл бұрын
I have just given up on mine. It's a Hoover DYN8+. I cannot get the seal to be watertight. I have tried several times using a variety of sealants and mastic compounds and used over 20 stainless steel bolts around the perimeter but when I fill the tub with water to test it there is always a couple of small leaks. Part of the problem is the that on this particular machine there is hardly any room to get the bolts in, it's as if the flange isn't wide enough to make this type of repair feasible ie it's designed to be welded from the outset and not just a "screwable" tub that has been used without screws. Now having spent several days on the job (I am retired so have the time) I have given up and off to buy a new one. The winner out of this is my brother in law who has an identical machine and will inherit a lot of spare parts!
@green-crocs-fixes1520
4 жыл бұрын
Commiserations Dennis, I assume the Seal you are referring to is the seal around where you have split the Tub and not the Bearings Seal. As i have stated in my video i used Gorilla glue because it expands as it dries, closing any gaps which had been overlooked, and yes i had to use tiny Nuts & Bolts as there is limited space in the lip around the rim of the Tub. Not much consolation @ this stage M8 but i suppose "nothing ventured" as they say. Regards.
@MrMatrixMinds
Жыл бұрын
Great clear vid thanks. Think I'm going to have to do this on my Indesit. Parts diagram and lists don't include bearings and seal, just complete drum unit. Any tips on how to find out what size bearings and seal I'll need before I take it apart?
@green-crocs-fixes1520
Жыл бұрын
Thanks Mr Matrix, there are no Bearings or Seal listed for an Eco or Sealed Tub as they are not designed to be replaced. You have to measure the old ones once you have removed them then request the sizes from an online Bearings supplier. Regards 😎.
@crushedz
5 жыл бұрын
Great video!Thanks.Smoothed the way big time!
@green-crocs-fixes1520
5 жыл бұрын
Thank Crushedz
@ginoharling4401
3 жыл бұрын
Such a shock to see you need to cut your drum open. Not done a bearing in years and grr what a eye opener. I had ago at cutting mine open and once apart noticed more damage to the drum. Thought shall I just tiger seal it and have my fingers crossed and hope it works and is good but it's now on the scrap heap
@green-crocs-fixes1520
3 жыл бұрын
Hi Gino, Most unfortunate, nothing ventured nothing gained I suppose. Maybe in the future you will have more success.
@iancoupe20v43
4 жыл бұрын
thanks for the video here we go then time to try it out
@green-crocs-fixes1520
4 жыл бұрын
ian coupe20v Thanx Ian , good luck, hope you are successful.
@iancoupe20v43
4 жыл бұрын
@@green-crocs-fixes1520 worked a treat thanks for the video and keep up the good work
@green-crocs-fixes1520
4 жыл бұрын
@@iancoupe20v43 Top man, well done.
@nitroboom1282
Жыл бұрын
Nice! ❤
@green-crocs-fixes1520
Жыл бұрын
.
@peters1393
4 жыл бұрын
Hi. Just did same job on my Hotpoint washing machine. But I've had one problem. My drum shaft is 35mm like yours so, ordered same set of bearings. But seal did not fit. My shaft has a cooper sleeve where seal is. So that seal from video was to small. And I couldn't find a set of bearings with good seal. Probably it's made on purpose, cos it's not designed for repair. Anyway I've ordered just a seal for Zanussi/Electrolux machines. Waiting for it now. Wish me good luck 🙂
@green-crocs-fixes1520
4 жыл бұрын
All the best Bikerski, Yes there is a Brass ring on the Shaft for the Seal. This can be heated off and a larger seal fitted. Regards.
@ferenczhucker4561
2 жыл бұрын
It wasn’t so long ago the drum used to split into two halves with a foam rubber gasket between and m10 bolts all around.
@green-crocs-fixes1520
2 жыл бұрын
Very true Ferencz, maybe manufactures prefer that we by another one of their machines rather than repair the existing.
@ferenczhucker4561
2 жыл бұрын
@@green-crocs-fixes1520 well the prices for a new drum complete with bearings is £250 for my model so to have it even replaced with labour costs added to the bill it’s more cost effective to buy new as you say. I would have never considered splitting the sealed drum until I watched your video, so thanks and bye 👋.
@hottuber2688
2 жыл бұрын
I have an expensive Bosch machine. Recently it started making a noise and I knew it was the bearing. However when I attempted to get repair I was told it was a welded tub like this and that a replacement part fitted would cost £480 from Bosch as the whole tub must be removed and a new one fitted. The Machine was about £600.00 This is deliberate. They don't want you fixing things.
@green-crocs-fixes1520
2 жыл бұрын
Totally agree HotTuber, they assume we all have five or six hundred in our back pockets, but as you see here there is always an alternative way around. Regards.
@hottuber2688
2 жыл бұрын
@@green-crocs-fixes1520 Thanks mate. I'm going to attempt this. This video is awesome.
@green-crocs-fixes1520
2 жыл бұрын
@@hottuber2688 good luck HotTuber, be aware that you have to measure the old Bearings radius, diameter and thickness, the seal also, then request these sizes from an online Bearings seller as there is no standard sizes. You won't find Bearing and Seal listed for you machine as they are not "replaceable".
@brendanschnurr9405
8 ай бұрын
Got bearings and seal out! Found replacement bearings. How do I find the same seal using dimensions of the old one? (Whirlpool doesn’t sell for my model as it’s “not repairable”)
@green-crocs-fixes1520
8 ай бұрын
Hi Brendan, there are no Bearings or Seal listed for an Eco or Sealed Tub as they are not designed to be replaced. You have to measure the old ones once you have removed them then request the sizes from an online Bearings supplier.
@georgiojansen7758
5 жыл бұрын
another wrench in the wheel of disposables👍
@green-crocs-fixes1520
5 жыл бұрын
georgio jansen Thanx Georgio
@onlyme972
3 жыл бұрын
@@green-crocs-fixes1520 really good video, fixed my machine so many times theres not much leftof the original, latest fix was replacing a dead pcb with the control panel and motor pcb from a machine of the same family, zanlussi jetsystem, perfect only i didnt have the facia so the dial needed to be printed out and stuck on
@green-crocs-fixes1520
3 жыл бұрын
@@onlyme972 sounds very innovative. Well done.
@billhoggy4461
Жыл бұрын
Great video but how do you know what bearngs to order i have a beko 8kg model WTG820M1W LOOKED all over to find the bearings. Can you help
@green-crocs-fixes1520
Жыл бұрын
Hi Bill, there are no Bearings or Seal listed for an Eco or Sealed Tub as they are not designed to be replaced. You have to measure the old ones once you have removed them then request the sizes from an online Bearings supplier. Regards 😃
@michaelwalsh9145
Ай бұрын
My zanussi has the same problem, I took the drum out yesterday but the lip on one side of the tub has a very thin ledge, too thin to get a small bolt in there, looks like the manufacturers are copping on to this fix.
@green-crocs-fixes1520
Ай бұрын
Thanks Michael, this has triggered my curiosity, gonna be on the lookout for one of those type to possibly find a work around 🤓.
@michaelwalsh9145
Ай бұрын
@@green-crocs-fixes1520 thanks
@sabudjed1135
2 жыл бұрын
Many thanks.
@green-crocs-fixes1520
2 жыл бұрын
You are welcome!
@speedmatters
5 жыл бұрын
Thanks for these videos, it's really helped give me the confidence to give it a go with our washer / dryer combo that just exploded in rust. One question though - how do you know what size bearings and seal to order before hand? Becasue it's a sealed drum, I can't find anywhere that can tell me what size bearings I need for my AEG washer / dryer. Many thanks :)
@green-crocs-fixes1520
5 жыл бұрын
speedmatters Thanx Sppedmatters, There are no listed Bearings and Seal for a Sealed Tub as they are obviously not designed to be replaced. What I did was measure the old ones once they were removed, then requested the sizes from an online Bearings supplier. Kindest Regards 😀
@speedmatters
5 жыл бұрын
@@green-crocs-fixes1520 Right, that makes sense! Thanks for the videos and the quick reply. Much appreciated 👍
@rod4530
3 жыл бұрын
Top man.
@green-crocs-fixes1520
3 жыл бұрын
Gee, Thanks Rod.
@rod4530
3 жыл бұрын
@@green-crocs-fixes1520 Welcome
@huskyng6981
7 ай бұрын
Hi I wonder if I can use aquarium silicone because it for water and safe for fish, so it safe on clothes too??? Thank you everyone
@green-crocs-fixes1520
7 ай бұрын
Hi Husky, not sure if it can cope with high temperatures but sure why not.
@MikeKruft
4 жыл бұрын
The last time I changed bearings on a washing machine was about 20 years ago on an old Service machine. It was pretty straight forward. Today I learned the true nature of the business. I started taking the machine apart and once the drum was out it became clear that it was a sealed unit. I had no idea about sealed units prior to today. I have a Hoover DYN 8164 d. I couldn't find any information about which bearings I would need to get as a replacement. Anyone have a have any experience of this model? The drum is 41021082 00. It's a green disaster!
@green-crocs-fixes1520
4 жыл бұрын
Hi Mike, I faced the same predicament prior. Never heard of a Sealed Drum either before this. So i had to measure the old Bearings and Seal and then requested the sizes from an online supplier. You won't find Bearings listed for a Sealed Tub machine as they are not designed to be replaced. Kindest Regards.
@markbrookes7822
5 жыл бұрын
Hi mate, great video, I'm gonna get round to doing mine as soon as i get the time. Only question I have is, regarding the bearing sizes, are the outside measurements standard or do you have to get the measurements for the outside too aswell as the inside measurement?
@green-crocs-fixes1520
5 жыл бұрын
Hi Mark, Good question, I think they only go by the inner ( shaft ) sizes however when ordering I always state the inner, outer and width sizes just to be sure, the Seal size also. All the best with your project. Kindest Regards.
@LexterLS400
2 жыл бұрын
He is not pulling or hammering or pressing the axle into the bearingsseat. I can see it clearly that he has got min 5 mm to go. I am trying now at trhis moment and i cant get it in its correct place. It is only 3-4 mm but i cant get it done.
@green-crocs-fixes1520
2 жыл бұрын
Hi Sonata, there is no Axle here ?
@ZSupremerulerZ
4 жыл бұрын
Very good job sir
@green-crocs-fixes1520
4 жыл бұрын
Thanks فضيلة الشيخ أبو تابانادا الياباني. hope it served useful. Regards.
@23mitch23piz
4 жыл бұрын
Can use silicone sealant instead of gorilla glue? To seal the drum back together?
@green-crocs-fixes1520
4 жыл бұрын
Hi Mike, Sure silicone, whatever gets the job done I suppose.
@SteveDrift31
5 жыл бұрын
Hey nice video, question: would it be ok to use a really thin angle grinder disc to separate the tub?
@green-crocs-fixes1520
5 жыл бұрын
Thanx Steve, whatever gets the job done I suppose, I have seen a couple of videos using grinders.
@stephenkelly5642
3 жыл бұрын
My Hotpoint washing machine has gone the same way. How did you know what size bearings you needed and where did you get them from.
@green-crocs-fixes1520
3 жыл бұрын
Hi Stephen, I ordered the Bearings and Seal after I removed and measured the old ones. I have done three of these so far and the sizes where always different. Kindest Regards.
@stephenkelly5642
3 жыл бұрын
@@green-crocs-fixes1520 fantastic thanks again for your reply.
@stephenkelly5642
3 жыл бұрын
By the way without people like yourself finding these things out we would just keep buying new washing machines. Again many thanks
@green-crocs-fixes1520
3 жыл бұрын
@@stephenkelly5642 Thanks Stephen, I also brought a new machine initially, but this one triggered my curiosity, so I thought I would have a go at repairing it. Fortunately successful but not easy for everyone.
@Martindyna
3 жыл бұрын
Indesit owned the Hotpoint brand until recently, they ruined the brand's reputation imo (used to be owned by GEC UK).
@franchise123ful
2 жыл бұрын
Nice one, my bearing came out and left the outer bearing stuck inside, struggling to get it out. Have there been any leakage since then?
@green-crocs-fixes1520
2 жыл бұрын
Hi Felix, had the machine for two years before I sold it, never leaked over that period. Yes sometimes the Bearings assembly disintegrates whilst removing, the bearings outer ring is what you should be striking anyway. Good luck and all the best. Regards 😀.
@franchise123ful
2 жыл бұрын
@@green-crocs-fixes1520 I had to buy new chisel to get it out.
@franchise123ful
2 жыл бұрын
All done mine is working perfectly no leakage would like to paste videos to show all
@green-crocs-fixes1520
2 жыл бұрын
@@franchise123ful Sure why not.
@franchise123ful
2 жыл бұрын
@@green-crocs-fixes1520 kzitem.infop5tlEAyi8us?feature=share here is the video of it spinning
@rogercarlucci-hodson4005
4 жыл бұрын
This appears to be an excellent video. I have exactly the same machine - I believe Indesit WIXL85 EX, with the same issue. Please could anyone advise as to where to purchase the drum bearing set, as the dealers I have contacted don't appear to stock it. Many thanks...
@green-crocs-fixes1520
4 жыл бұрын
Hi Roger, You won't find any Bearings sizes listed in any catalogue for your Indezit Washing machine because it has a sealed tub.which is not designed to be replaced. Not sure what size Bearings and Seal your particular machine has, I measured the old ones in from my unit (@) the Bearings sizes were; 30mm= outer, 35mm=inner and 38mm seal. Just ordered the sizes off eBay via a bearings supplier. Kindest Regards,
@philbrookman3126
4 жыл бұрын
mines just gone ,,,i am supposed to have a 10 yr parts warranty so rang them oh no our fitters have to fit them ok how much for 1 hrs work 120 quid ,,, ok so send me the parts i will fit cant do that ,,so they make a sealed drum so they expect u to throw away the washing machine or the entire drum because of bearing failure ,,, and u wonder about our planet the throw away society has to stop...
@green-crocs-fixes1520
4 жыл бұрын
Hi Phil, Strongly recommend that you persue this one as they are legally obliged to honour their warranty. Maybe contact Watchdog or Rip Off Britain television programs (if your UK). Seems as though the prefer consumers to purchase a new machine these days rather than repairing it, and then there's Landfill. Kindest Regards.
@zannahmartell9813
Жыл бұрын
I'm taking my old Samsung apart and turning the tub into a garden planter
@green-crocs-fixes1520
Жыл бұрын
Superb Zannah, recycling is good.
@ThePetitcon77
4 жыл бұрын
Hello top video which site did you find the glue and the bearings and the seal? my model is an indesit pwc8148w (fr) tank of a block.
@green-crocs-fixes1520
4 жыл бұрын
Hi ThePetitcon, Thanx. There are no listed Bearings and Seal for your Sealed Tub washing Machine as they are obviously not designed to be replaced. What I did was measure the old ones once they were removed, then requested the sizes from an online Bearings supplier. The Gorilla glue can also be purchased online or from any major DIY store. Regards.
@trickytricky7401
5 жыл бұрын
I have watch a couple of these videos , and I decided to have a bash at fitting new bearings to my Panasonic washing machine witch took all day , it now works perfect , I used a completely different method from this video , there are lots wrong with this method , I will just give three , 1 the gaiter that goes round the machine front must come off . 2 you should take the front of the machine off so you can take the drum housing through the front of the machine , 3 the nut that keeps the pulley in place is not its main job , it is there to pull the shaft on the inner drum into the seal and if this is not tighten enough it will fail and you will be back to square one , there is more and I will try to upload a video .
@green-crocs-fixes1520
5 жыл бұрын
Hi Tricky, Congratulations on replacing the Bearings on your Panasonic washing machine. Tricky the Indesit washing machine demonstrated here is manufactured as 1: a spot welded housing unit so it is not possible to undo the front as there are no screws, so, 2: there was no need to completely remove the front Gaitor or Tub Bellows Seal from the entire unit. 3: The pulley will fall off its shaft if the 8mm torx bolt is not fitted. Kindest Regards.
@mrvlhs
4 жыл бұрын
Thank you for the great video. How do you figure out what bearings to purchase before opening the machine apart? Because the tub is sealed, the assistance manual I found makes no reference to the bearings, just the tub.
@green-crocs-fixes1520
4 жыл бұрын
mrvlhs Thanx Mrvlhs, Our original machines Bearings failed so I was shocked that these so called Eco-Tubs where not repairable which meant a new machine or a new £600 replacement tub. I had already replaced our machine however I thought there has to be a work around. After splitting the Tub and removing the Bearings and failed Seal I simply measured the old ones and requested a new set from an online Bearings supplier. Regards.
@mrvlhs
4 жыл бұрын
@@green-crocs-fixes1520 how long did that take you? I'm not sure I can be without the tub for long :)
@green-crocs-fixes1520
4 жыл бұрын
mrvlhs Done three so far, this is the second. As I said before I had already brought a replacement machine. But the old one was sat in the shed, begging for attention 😀
@mojkanal212
5 жыл бұрын
god job two questions, what exact glue you use, and if is that same glue good if I got washer/dryer machine, maybe use some silicone glues or sealenat will be better ? what you suggest ? thank you
@green-crocs-fixes1520
5 жыл бұрын
Hi Mojkanal, the answer to your initial question is clearly visible @ 14:26.... And secondly sure you can try silicone sealant if you think it will be better. Regards.
@mojkanal212
5 жыл бұрын
@@green-crocs-fixes1520 thank you, I cant buy that gorilla glues where I live, but I will find the replace for gorilla :) thx again
@georgiojansen7758
5 жыл бұрын
@@mojkanal212 i think that's polyurethane pur
@terrymorgan7585
4 жыл бұрын
What size bit did you use to remove the wheel from the back?
@green-crocs-fixes1520
4 жыл бұрын
Terry Morgan Hi Terry, I assume you are referring to the Pulley Wheel. It was a T30 Torx Key, I have a set so it may be different. Regards.
@terrymorgan7585
4 жыл бұрын
@@green-crocs-fixes1520 thanks and yes I did me the pulley wheel, I went blank when I was writing haha. The reason I ask is on mine it is closer to a T40 but it keeps slipping under pressure although neither part are rounded and I've tried a few different bits in case it was a dodgy part... I suppose my question is do they have some that have a bespoke fitment?
@green-crocs-fixes1520
4 жыл бұрын
Terry Morgan Hi Terry, Not sure if there is a standard head bolt that fits. Maybe wacking with a hammer, might shock it free ?
@nickskinner7682
4 жыл бұрын
hi many thanks for vids just gt round to trying my 1st one gt the bearings in ok but the seal im really struggling with as its a diffrent seal exsact same as urs in vid whats the bit u use from the car jack whats the measurements as just gt my bit but seems to small and i dont wanna damage anything
@green-crocs-fixes1520
4 жыл бұрын
Hi Nick, Thanx, Stuggled with the Seal myself if you watch carefully as it did not go in straight @ first. Not sure of the dimension of the Car Jack Cup which I used, this was two years ago. If you could find something to fit around the rim of the Seal, And strike it home, some grease may help. Regards.
@thedentchaser443
4 жыл бұрын
Hi, tried to carry out this repair and a brass sleeve on the shaft of the drum wrecked my seal, if I get this brass sleeve off with I be able to get another of the same seal and fit it without it leaking? It’s on an Indisit very similar to this one and I removed the same looking seal as you and fitted one that looks the same as the one you fitted. Thank you for your video.
@green-crocs-fixes1520
4 жыл бұрын
Hi Dent Chaser, Yes. I have done three of these so far, one the seal was so badly worn that it damaged the Brass Sleeve. Measured and managed to obtain a Seal and Bearings for the inner. Kind Regards.
@thedentchaser443
4 жыл бұрын
Green-Crocs-Fixes thanks for your reply, I will order another kit and heat the ring off, do you just use a heat gun?
@green-crocs-fixes1520
4 жыл бұрын
The Dent chaser Hi I used a Blow Torch to remove mine 😐.
@thedentchaser443
4 жыл бұрын
Brutal mate, love it! Will give it a go with the heat gun. The machine in this video, is the shaft on the drum the same size where it seals as where the internal bearing sits (the bearing next to the seal). Thank you for your time, I really appreciate it!
@green-crocs-fixes1520
4 жыл бұрын
The Dent chaser Sorry I meant a gas heat gun, what they use to Solder pipes.
@confucious100
4 жыл бұрын
I am about to have a go at doing this job on a Hoover DYN 8144D but my concern is that I won't know the size of the bearings and seal until I get it all apart and no one seems to sell the bearing/seal kit as it's got a sealed tub. I guess I will just have to take measurements and contact a number of suppliers and hope that bearings/seals are available.
@green-crocs-fixes1520
4 жыл бұрын
Hi Dennis, You are correct, as the Tub is not serviceable there are no parts listed only the whole unit. Done three of these Sealed Tubs so far from different models. Bearings / Seal are never the same size. An online seller will be able to supply the sizes you request. Regards.
@stephenrylands1269
4 жыл бұрын
How did you know what bearings to get before opening the machine up??
@green-crocs-fixes1520
4 жыл бұрын
Hi Stephen, I ordered the Bearings and Seal after I removed and measured the old ones. I have done three of these so far and the sizes where always different. Kindest Regards.
@stephenrylands1269
4 жыл бұрын
Cheers mate 👍
@andrewsmith8688
4 жыл бұрын
How did you know the size of bearing required to fit for your machine
@green-crocs-fixes1520
4 жыл бұрын
Andrew Smith Hi Andrew, There are no replacement Bearings or Seal listed for a Sealed Tub or Eco-Tub Washing Machine as they are not designed to be replaced, hence why the unit is glued together where as conventionally they were bolted together. So you have to measure the old ones once you have removed them, then request the sizes (Bearings and Seal) from an online Washing Machine Bearings seller. Regards 😀.
@andrewsmith8688
4 жыл бұрын
Thanks, just thought you could of saved me taking it apart before hand. 👍
@twocents5043
4 жыл бұрын
can anyone kindly link where this exact set of bearings can be bought? Is it a set?
@green-crocs-fixes1520
4 жыл бұрын
Hi Two Cents, This is a Sealed Tub, as the Tub is not serviceable there are no parts listed only a new whole unit. Done three of these Sealed Tubs so far from different models. Bearings / Seal were never the same size. An online seller will be able to supply the sizes (Bearings / Seal) you request once you have measured the old ones Kind Regards.
@twocents5043
4 жыл бұрын
My tub is the same as the one in your video. Great job you did. Man after my own heart with that cutter. Is the bearing set for this tub these HOTPOINT Washing Machine 35mm C00202418 ?
@green-crocs-fixes1520
4 жыл бұрын
two cents Hi, Yes 35mm. Just emailed a Bearings seller on eBay the sizes, Cost about £16.
@user-ey1vq1bi9y
8 ай бұрын
Which Indesit model is this?
@green-crocs-fixes1520
7 ай бұрын
Hi User-ey, cannot remember as it has been a few years.
@davidbunting3300
5 жыл бұрын
I'm giving this a go, got the drum opened, I am just a little concerned about getting it sealed water tight, I noticed you used PU glue, do you find that's the best thing to use? I drilled plenty of holes to ensure I can get plenty of bolts in I'm just worried about it not being watertight when I get it back together. Great video.
@green-crocs-fixes1520
5 жыл бұрын
Thanx David, a common question, some people use Silicone or Resin. I used this glue because of its water resistant qualities and it helps to adhere the two halves together like the manufacturer had done initially. Gorilla Glue also expands as it dries filling any gaps missed. All the best David, hope you're successful. Regards.
@pingu00728
5 жыл бұрын
I want to give this a go. But how do you find out the part number for the bearing set. The website I usually use for spare parts don't sell them for my model as they say you need a whole new drum.
@green-crocs-fixes1520
5 жыл бұрын
Hi Richard, You have to measure the old Bearings radius, diameter and thickness, the seal also and then request these sizes from an online Bearings seller. You WILL NOT find a set of Bearings/Seal listed for your machine model as it is a sealed unit and they are not suppose to be replaceable. You have already split the Tub so when you knock the bearings out measure them and the seal. The sizes for this machine were: 30mm= outer / 35mm=inner / 38mm seal. Yours may differ as there is no standard size. Regards.
@davidbunting3300
5 жыл бұрын
I saw a set on eBay that matched my measurements and also stated the model number. However when they arrived the bearings were spot on but the seal was different. Got it all back together last night hoping to test it later today or tomorrow. I decided to use PU glue as you have. Fingers crossed for no leaks. Thanks again for the great video.
@sammytheseal2307
4 жыл бұрын
The manufacturing processes should be regulated. Consumer right to repair etc. I think the EU is forcing manufactures to provide spares and cater for people to repair rather than replace from 2021, but it shouldn't have had to come to that.
@green-crocs-fixes1520
4 жыл бұрын
I agree Sammy, as the Steel from your old unit may be recycled but the is just Land Fill. Regards.
@sammytheseal2307
4 жыл бұрын
@@green-crocs-fixes1520 Yep, washing machines used to last 20+ years before they got scrapped, as they were easily repairable. Now most of them are scrap after 5 years, if that..
@akramlool
5 жыл бұрын
I have done that the same from another video I saw for u But there was some leak So it did not work properly coz the water switch dose not stop I think j need to put glue again 😑
@green-crocs-fixes1520
5 жыл бұрын
Hi Akramlool, You can check the Tub for leaks while you still have the unit out, just pour some water in block the Sump and rotate the whole Tub. Regards.
@LosSerpent
3 жыл бұрын
hey man, did the fix hold up? i didn't cut very well because i used a angle grinder, i'm wondering if it's worth to buy bearings, sand down the thing and try to make it stick together
@green-crocs-fixes1520
3 жыл бұрын
Hi Los, I have repaired three so far. Used it for about 18 month’s then sold it on eBay. There are no replacement Bearings or Seal listed for a Sealed Tub or Eco-Tub Washing Machine as they are not designed to be replaced, hence why the unit is glued together where as conventionally they were bolted together. So you have to measure the old ones once you have removed them, them request the sizes (Bearings and Seal) from an online Washing Machine Bearings seller. 😀.
@LosSerpent
3 жыл бұрын
@@green-crocs-fixes1520 no luck sadly, I Couldn't get the bearings out, even with wd 40,there was too much corrosion. Well it probably wasn't even worth it anyways since I didn't cut it properly. Guess it will be. For next time thanks
@green-crocs-fixes1520
3 жыл бұрын
@@LosSerpent Nothing Ventured and all that Los Serpent, the old Bearings can be stubborn sometimes to remove. I used a Saw to split the unit because the blade is thin.Better luck next time.
@LosSerpent
3 жыл бұрын
@@green-crocs-fixes1520 yeah honestly i just rushed the process a bit because i didn't have much time, if my next washing machine breakes down like this i'll fix it properly. thanks... about all the piaces i have from this one, engine etc, do you think they're worth keeping? for spare parts for another washing machine? or are the pieces much different in every other brand?
@torritt
3 жыл бұрын
Has anyone done this on a hotpoint washer / dryer bhwd129 ?
@green-crocs-fixes1520
3 жыл бұрын
Hi David, should be the same procedure if Sealed.
@MiGujack3
2 жыл бұрын
Omg I have the same cursed machine and I think it has a bearing issue (I recently replaced a snapped spring)
@green-crocs-fixes1520
2 жыл бұрын
.
@trannguyenanhson7915
5 жыл бұрын
Hi Dave, Thank you for the Nice video! Mine Indesit Model IWC 8125 (UK) I would know its as big "ask", but can anyone please help to instruct me in the right bearing and seal order to my country in Vietnam? Regards,
@green-crocs-fixes1520
5 жыл бұрын
Hi Tran, Wow... All the way from Vietnam. Not sure what size Bearings and Seal your particular machine has, I have done three of these Sealed Tubs so far, one Hotpoint and two Indezit. All coincidently had the same sizes: 30mm= outer / 35mm=inner / 38mm seal. Just ordered the sizes off eBay via a bearings supplier.
@tranduylam9213
5 жыл бұрын
Dear Bro! Really appreciate your quick reply and support! I would like to have more question if possible give me the link of your bearing order on ebay or any part numbers or your Indesit model numbers? Thanks again! Regards,
@trannguyenanhson7915
5 жыл бұрын
Hi Dave, I just found the parts on the site in UK as the link in below! Can you help to check whether is correct or not? www.indesitspares.co.uk/washing-machine/30mm-bearing-seal-kit-6205z-6206-2rs/product.pl?pid=1111685&path=601906&refine=bearing Regards,
@green-crocs-fixes1520
5 жыл бұрын
Hi Tran, You have to request the sizes once you have measured the bearings. Just because they are from Indezit does not mean that they will fit. You are replacing the Bearings and Seal on a machine with a Sealed Tub, and as they are not designed to be replaced, THERE ARE NO BEARINGS SET LISTED OR CATALOGUED FOR YOUR MACHINE ONLY A. NEW TUB. Hence why you had to cut the Tub open. My method is to contact a couple of eBay sellers who sell bearings, and ask them for washing machine Bearings and Seal sizes which I had measured from the old ones. Never paid more than about £15.00p for the set either. The bearings should look some thing like this: www.ebay.co.uk/itm/INDESIT-Genuine-Washing-Machine-Drum-Bearing-Kit-6204Z-6205Z-C00251855/273341509875?epid=7010916782&hash=item3fa46c70f3:g:X7QAAOSw6QpbP4sz:rk:29:pf:0 Kindest Regards.
@trannguyenanhson7915
5 жыл бұрын
Dear Bro, Nice to get your detail guide! Really helpful for your information! Thanks and Best Regards,
@reanne20
2 жыл бұрын
Lucky this unit is still looks new,how bout if the bearings are rusted
@green-crocs-fixes1520
2 жыл бұрын
.
@maidenstrat1
4 жыл бұрын
Good video mate, made me cringe a bit when you were hitting the bearing so hard. Been doing mine today, 6 hrs later and I still not got the outer plastic cut away fully. Will order the bearing tomorrow, bolts, nuts and washes too. Good point using Gorilla glue, I have a bottle in the cub board.Cheers
@green-crocs-fixes1520
4 жыл бұрын
Thank Cbf1A, and all the best with your project. Hope you are successful, Kindest Regards.
@andjuju6476
4 жыл бұрын
Does Fisher & Paykel sell them green crocs?
@green-crocs-fixes1520
4 жыл бұрын
?
@andreipreda5705
4 жыл бұрын
INCREDIBIL SCRIE SI IN ROMANA
@green-crocs-fixes1520
4 жыл бұрын
Mulțumesc Andrei Preda, încercând să ajungă la un public mai larg. 😎
@VENTUSVEVO
4 жыл бұрын
WHAT KIND OF GLOU YOU USE?
@green-crocs-fixes1520
4 жыл бұрын
Hi see 14.27
@andreipreda5705
3 жыл бұрын
daca scrie in romana cumva esti din romania 😃
@green-crocs-fixes1520
3 жыл бұрын
Bună nu română. Am folosit Google pentru a traduce, deoarece românii urmăresc foarte mult acest videoclip. Mulțumiri.
@sanjayabandara8833
4 жыл бұрын
Thanks🍎🍎🍎🍎
@green-crocs-fixes1520
4 жыл бұрын
Welcome 😊
@Roddis
2 жыл бұрын
Fuck that for a game of soldiers... But Very interesting Thank you
@green-crocs-fixes1520
2 жыл бұрын
Erm... thanks Raddis, happy to catch your interest at least 😊.
@jwoodard621
4 жыл бұрын
What kg is your machine thanks
@green-crocs-fixes1520
4 жыл бұрын
Let me check
@DavidMartin-vl4zd
6 жыл бұрын
Great video. My bearings have just gone (rumbling noise past couple of weeks and now oil on the clothes), so took apart and found it was a sealed tub. Have spent literaly hours trying to find the bearings on Ebay, but can't find anything that ties to the model. Any ideas how I find this out (I'm practical + okay with tools etc, but rubbish on a computer). It's an Indesit Eco Time Energy Saver 8KG Model IWE 81481 ECO (UK) S/N 209085226 30788300000 I know its a big "ask", but can anyone please steer me in the right direction? Cheers, Dave
@green-crocs-fixes1520
6 жыл бұрын
Hi Dave, You won't find any Bearings sizes listed in any catalogue for your Indezit Washing machine because it has a sealed tub.which is not designed to be replaced. Not sure what size Bearings and Seal your particular machine has, I measured the old ones in from my unit (10:25) the Bearings sizes were; 30mm= outer, 35mm=inner and 38mm seal. Just ordered the sizes off eBay via a bearings supplier. Kindest Regards, Dave.
@DavidMartin-vl4zd
6 жыл бұрын
Thanks Dave for getting back to me so quickly. Yep, I'd guessed after a while of looking that it may be because it's not classed a a replacement part, but nice that you have confirmed this. Got the tub apart, but wish I'd had an electric saw like yours - a semi-blunt panel saw was the best that I could muster today as I didn't think I'd get away with using my jigsaw (fear of twanging the inner drum). It took ages :) Wish I'd videoed the removal of the bearings as they were very tight and had to resort to using a lot of brutality, especially with the inners. Measured the bearings and they are the same as in your video, but I need to check the seal (will need to try to re-shape it as it was a bit buckled by the time I'd finished with it). Hopefully get this finished before the missus orders a new machine :) Thanks again for your inspirational video, Dave
@green-crocs-fixes1520
6 жыл бұрын
No worries Dave, Cutting the Tub apart is the hardest part of the whole process, tried my Jigsaw also but found the big one easier. Dave the video has been edited to make it look easy, I also had to get lively with the hammer and cold-chisel to remove the bearings. I had already brought a new machine prior to attempting this project. Hope you are successful with your project also. Regards.
@samueljamesify
5 жыл бұрын
Hi green crocs,have a indesit xwa 71451 and I know you've been asked quite a few times but am the end of my tether,am determined to get it working again.ordered off amazon because the picture of the bearings where exactly like the ones I took out , the seal has ball bearings in it so I thought I would gamble and by them but what arrived were completely different so sending back . The outer bearing has a 25mm diameter which Amazon sent me was right and the inner bearing which should have been 35 mm dia with oa size at 62 mm same as seal, I've looked on e bay but they don't give any sizes . The pictures right but comes up with part no co251855 and compatible parts numbers but this is same as Amazon which was incorrect. Can you please help me out I would be very grateful. Good video
@green-crocs-fixes1520
5 жыл бұрын
Hi Simon, Had to measure the old Bearings radius, diameter and thickness, the seal also and then request these sizes from an online Bearings seller. You WILL NOT find a set of Bearings/Seal listed for your machine model as it is a sealed unit and they are not suppose to be replaceable. Simon your machine is not exactly the same as mine so you cannot use this as a guide for your specific parts. It is imperative that you measure the removed Bearings/Seal. Hope this helps. Kindest Regards, Dave.
@franchise123ful
2 жыл бұрын
@@green-crocs-fixes1520 mine is exactly like yours, where can I buy same, the one I bought came smaller in the outer diameter
@green-crocs-fixes1520
2 жыл бұрын
@@franchise123ful Hi Felix, there are no Bearings or Seal listed for an Eco or Sealed Tub as they are not designed to be replaced. You have to measure the old ones once you have removed them then request the sizes from an online Bearings supplier. Regards 😀.
@jwoodard621
4 жыл бұрын
We've done what you've done but the bearing I got didn't fit our machine type is INDESIT IWC 91482ECO THANKYOU PLEASE HELP THANKYOU
@green-crocs-fixes1520
4 жыл бұрын
Hi Jackie, The problem is there are no Bearings Seal listed for your machine as they are not replaceable. As this is a sealed unit. You have to measure the old ones and then request the sizes from an online Bearings seller Regards.
@jwoodard621
4 жыл бұрын
@@green-crocs-fixes1520 thankyou for that anyways for all your help
@aboosama5709
3 жыл бұрын
ممتاز💞💞💞
@green-crocs-fixes1520
3 жыл бұрын
Ok Thanks.
@MariusMarius-tt1vq
2 жыл бұрын
umple semeringul cu vaselina
@green-crocs-fixes1520
2 жыл бұрын
cam intarziat Marius dar multumesc 😎.
@jwoodard621
4 жыл бұрын
It's 9kg machine
@green-crocs-fixes1520
4 жыл бұрын
OK
@amerriaz10
4 жыл бұрын
what a palava, get a new one , they are cheap
@ek8710
4 жыл бұрын
No they're not, plus it's the principle. Tubs are only welded by manufacturers to force you to replace them when the bearings go. It's something that will be probably outlawed in the EU soon. (Look up planned obsolescence)
@green-crocs-fixes1520
4 жыл бұрын
@@ek8710 Top response Sausage.
@johndavies4644
4 жыл бұрын
Thats the problem with society.. replace it attitude. My mrs has a 2007 imac. The GPU failed. I didnt bin it, i reflowed the solder in the oven by baking the board. 3 years later and its still working. Any fool can spend money and buy new.
@torritt
3 жыл бұрын
As a society we need to learn to repair instead of renew otherwise there will be problems for future generations
Пікірлер: 234