I'm about to get back to work on this again. As soon as I can get the coupler off of the old crankshaft I'll be working to start reassembly on the engine; and will get to work on filming the next installment for this project.
@Myotherhobbies
4 жыл бұрын
Joing the wave raider Gang on face book its a great group...
@ksmetalfabrication5808
3 жыл бұрын
Did you have to re-sleeve the cylinder or was There enough material to bore out to 84 mm?
@VHickleGarage
3 жыл бұрын
There was enough for 84mm. If I remember correctly there is suppose to be enough meat on the cylinders to go up to 84.5mm max.
@noah2016999
3 жыл бұрын
Hey man. Great video I am in your boat my cylinder 1 is shot. I'm looking into bug bore kits. What kit did you use and where did you buy it? Were they able to bore the stock sleeves in the cylinder? What did it cost to have them bored out? And lastly what size jets are you planning on using I was told you need to rejet with leaner jets once you go big bore. Thanks!!! SUBSCRIBED!
@VHickleGarage
3 жыл бұрын
I used a WSM kit for standard bore for a 1200, to get 84mm pistons. I think I got it off ebay. I had the stock sleeves bored, they're suppose to be able to go to 84.5mm. I think it boring was about $400. I don't think leaner is a good idea. . You're increasing displacement so it will already be leaner on stock jet size. I went up in jet size a bit, but I can't remember what sizes off the top of my head. Greenhulk.net has some good info, and I have build thread where I think I listed the jets.
@noah2016999
3 жыл бұрын
@@VHickleGarage Great thank you! Would you be able to post a link to that thread? Habe you got it running yet with your new jets? If so I'm going order what you got.
@VHickleGarage
3 жыл бұрын
Here is the link: greenhulk.net/forums/showthread.php?t=274246 I haven't gotten the thing fired up yet unfortunately. The engine is fully assembled, I have a video of that that I need to finish and upload. Life got in the way and this project got pushed to the back burner. I need to swap jet pumps, and do some hull prep so I can drop the 1100/1200 into the purple hull and fire it up. I didn't want to start it without the exhaust hooked up since it won't run right anyway. Hoping to get back to this build in the not too distant future, but a couple of my cars need more attention first.
@noah2016999
3 жыл бұрын
@@VHickleGarage I get it man thanks for all the info! If you have a chance could you look and see what jets your orderd? I didn't see that in the post. Thanks again man!
@VHickleGarage
3 жыл бұрын
Just checked, I ordered new 1.5 Needle and Seats, then got jets to run 115/80 on #1 and #3, then going to reuse the 107 along with a new 80 low speed jet for #2. MPeavler on the form suggested not running staggered jet sizes between cylinders, so I would heed his advice. I know absolutely nothing compared to him. His builds and BullRaider are something you should really spend the time to search and read through, you won't regret spending the time to do so.
@motomizfit2892
3 жыл бұрын
Any update? Would love to see how this turns out
@VHickleGarage
3 жыл бұрын
I've gotten the engine fully reassembled, but I need to order a couple Carb Jets to be able to fire it up. Video of engine assembly is 90% complete. Going to try to order the jets and get the engine fired up for the first time in the next couple weeks, will post that video after I get it started. Then I'll be making Part 3 finishing up the Hull Prep. Sorry it's taken so long. . Hopefully soon.
@ls1_cammeroh
3 жыл бұрын
What would you offer someone for a 94 that hasn’t been ran in about 7 years. Hull looks to be in a little worse shape then the one you washed
@VHickleGarage
3 жыл бұрын
If it looks worse, and been sitting that long I wouldn't pay much. Check the pump. It was rotten on the free hull I got. If that's the case I wouldn't pay more than $50. If the pump and engine seem ok, then maybe up to $200.
@ls1_cammeroh
3 жыл бұрын
@@VHickleGarage the guy wants 500 for it by itself
@VHickleGarage
3 жыл бұрын
@@ls1_cammeroh Way too much imo. I paid $400 for a pristine 94 700, 6 years ago.
@ls1_cammeroh
3 жыл бұрын
@@VHickleGarage I think I’m going to pass on it then
Пікірлер: 17