You could use the No Overtaking when Turning Vehicle stickers, on the black rear plastic
@stuartkcalvin
15 минут бұрын
Beat me to it.
@treeman3663
51 минут бұрын
Hi guys The whole Reno has been awsum enjoy your travels
@brigittedossor8167
Сағат бұрын
Great job but....love Erin's laugh😂😊
@PeterLongworth-u8d
2 сағат бұрын
I did the same with the bottom fill. I don't have a litre counter but I slow the flow right down when nearly full to give the water time to level out that way I don't think you would need to block of the Fillers. Love you're Videos
@themacs488
5 сағат бұрын
You need the yellow and black DO NOT OVER TAKE rather than the boring black plastic. Get them made same size and stick them on. They will take away the bareness, cheap and super easy to fit.
@paulwashere.2121
39 минут бұрын
The problem with getting them made is they might be illegal. The Do Not Overtake Turning Vehicle signage has to be a specific size and at a specific height and made from a specific reflective material.
@JanShephard
3 сағат бұрын
Either add the black all the way across or add the checker plate in the middle
@davetunbridge6637
Сағат бұрын
Breather would work better if on the top of the tank and possibly if it was bigger. Also filling the tank is a bit like charging the battery, bulk fill initially then top up a bit slower towards the end to get max capacity. Agree with others regarding putting some “ Do Not Overtake Turning Vehicle “ stickers on the black plastic.
@prospectorpete
4 сағат бұрын
I think the black strip would look better if it went the full width of the van
@diannecain1
29 минут бұрын
Or painted white to match the van
@maxmckenzie2560
5 сағат бұрын
I’m goin to Bunnings to get a “litre-metre-reader-thing” 😂 On a serious note I really appreciate the caravan plumbing lesson in this ep Thanks
@bradleyatherton4546
44 минут бұрын
Overtaking stickers will look good on them
@carolmcmillan1108
4 сағат бұрын
Enjoy your travels with all your modifications 👌👌
@Anthony-and-Donna
4 сағат бұрын
Congratulations, van looks great!!
@mattbirks7032
3 сағат бұрын
Now my Sunday arvo is catching up on videos!! Good seeing you repping the best mechanic in the business! JGMS❤
@todddienhoff4223
5 сағат бұрын
Hey guys , My is toddy and I’m 42yo type 1diabetic and am suffering with complications from diabetes which has me down to 42kg.I had to sell everything to pay for treatment and it didn’t work so I had enough money left to buy a 2007 Jeep Patriot so I’m asking if you can help me with some advice on what I should do to it so I can go camping and what would I need if i am able to come to the next camp for a cure.The nurses at the Mater hospital showed me your channel and they literally come and watch an episode with me while I get an infusion to make me smile and I’m so grateful that now iv found something to make me smile every single day and that’s catching up on all your past episodes.thanks so very much for your continued content and please know that they make me feel a little bit better each day.hope to meet you guys one day hopefully I’m able to camp for a Cure Much love Little Toddy D T1D❤
@jasonstratman1618
3 сағат бұрын
I cant unsee the new eyebrows on the back of the van.... looks great!
@lynparsons6539
5 сағат бұрын
Yay!! Yep we agree with the other comments snd reckon get the Do Not Overtake Stickers. 👍👏👏👏👏looking forward to your adventures, 😊 Lyn & Bobby
@SuperHosko
3 сағат бұрын
Those plates look like johnny Howard's eyebrows 😂 I agree with previous comments though about the yellow do not overtake turning vehicle
@Nosaesoh
Сағат бұрын
Decal 400mm Font “Do not Overtake Turning Vehicle” allows you to legally swing wide at an intersection. And cover the black plastic
@beercooler
3 сағат бұрын
I have the exact same tanks in our Gator X and fill will the standard fill point and get about 85lts using the same litre meter reader. As you would know the Gator X has air bags and I raise the fill side of the van to get the breather outlet in the tank to the highest point.
@jenafraser7470
3 сағат бұрын
Add more stickers to the black panels as you travel 😊 then intentional and will match your drop down bench
@peterrutter3622
4 сағат бұрын
Really enjoy your content guys. Like the humour and down to earth approach. Maybe to sort the water tank issue you could move the breathers to the top of the tank to eliminate any airlock. Hope this helps.
@brenjud
5 сағат бұрын
Enjoy your videos. We will be coming to Camp for a Cure 25
@lackatit
4 сағат бұрын
Another option for the back of the caravan is to get stickers made up that say Big Bertha Thanks for a bit of an insight to the plumbing, also the Bunnings flow metre thingy 😅
@ab7406
4 сағат бұрын
Yes best to fill tanks from bottom and remove filler caps when filling ( air needs to escape and tank fills faster ) Cover caps to water inlet and mains inlet for dirt and bugs. White JG pipe ( reinforced ) is better for hot water system. 1/2in black pvc pipe would of done from filler manifold, same as draw to pump. Accumulator tank after pump are great
@BazzMann48
Сағат бұрын
The inlet on each tank need to go in the top. At least near the top, otherwise, the pressure will eventually cause the tank to crack at the joint (like the example you showed at the beginning of the clip). Cutting the "eyebrows" on an angle (inside edge [/ \]), would improve the look. I like the "Give Way to Turning Vehicle" signs as others have suggested. I think this episode, was more interesting/entertaining than watching the Super Cars at Mt Panorama today. Cheers..
@cathbp4089
32 минут бұрын
Going to miss the shed build. safe and happy travels. Could you paint the black plastic white?
@luckycountrytravellers6488
Сағат бұрын
Erin you won’t even notice the two plastic pieces after a while.
@JacksonBiggles
5 сағат бұрын
Could you let people know the size of the ball valve you use to block off the gravity feed inlet please that's a lot of extra water you're missing out on ! To save Bunnings trauma in the plumbing section.
@Davwaltech
Сағат бұрын
Am working on the same issues you have with water tanks but I have one filler and one breather for two tanks which is a bit of a pita..just wondering what you will do when you want to drain the tanks? Good work on the van btw!
@DeneOLoughlin-ek9ee
9 минут бұрын
If you insert the internal pipe sleeves available for John Guest pipes at the join with the fitting you will get a much more stable connection less likely to leak.
@geoffcathcart7154
2 сағат бұрын
You wreck it when Aaron was standing underneath the filler tap outlet . 😂😂😂 . Hay why don’t you put a one way valve on filler pipes instead of the ball valve thing .
@Panda55
3 сағат бұрын
I'm a bit confused. If you fit the ball valve to your gravity fillers how is the air going to get out of the tanks when you are pressure filling them? I don't think the vents that come up to your filler caps will be big enough to let the air out quickly and I've seen people split their tanks if they try to fill too quickly. Also you will need to make sure the air vent pipes don't have air locks from the water or you won't get air back into the tank when pumping from the tanks. Just a couple of things to think about hope this helps.
@jimmyintel
5 сағат бұрын
Definitely need stickers on the black panels
@kristinaobst15
Сағат бұрын
I'm a bit like you Erin, not really sure with the black bits. What about continuing it along the back so it's like a strip? I feel that wouldn't look so random
@paulwashere.2121
43 минут бұрын
Check your water delivery meter. I have one the same and it shows 18L when I fill a 20L jerry so it reads under. Yours might be the same.
@PaulJunor-sv9wn
2 сағат бұрын
I have the same water tanks and the most I can put in is 75 litres. I think they are labelled wrong.
@kerryscott2552
3 сағат бұрын
kerry see you on the road somewere
@Rosco_Y
21 минут бұрын
Enjoy you content…Think you need 3 x 12mm John Guest non return valves 1 for each tank to ensure you don’t lose any water if a tap leaks or gets knocked.
@tim18118
2 сағат бұрын
Alex, what’s the right silicone to use to seal the connections in the water tanks? About to do some mods on mine to add an extra tank.
@johnboyle4355
2 сағат бұрын
While you are at it, were is you DO NOT OVERTAKE TURNING VEHICLE, as you are over 7,5 Mts in length, I think it is a legal requirement.Put it on your new bit of plastic.on LEFT side.
@Accolades70
3 сағат бұрын
Noice...
@alanheather8441
4 сағат бұрын
Are you happy with your suspension on the van or would you change to off road suspension
@Livedaybyday71
6 сағат бұрын
Wicked shirts
@petercruickshank9633
2 сағат бұрын
Use checker plate
@GraemeLowry-v9b
26 минут бұрын
What about a simple non return valve in your old filler lines.
@diannecain1
28 минут бұрын
Paint the black plastic to match the van
@rickbailey1074
5 сағат бұрын
I done the same thing with our tanks I fill them from the bottom but I just used our water hose that I had a metre of left over Wish you would have sliced open that split water tank to see the internal baffles because we have the same problem 95l tanks but can only get about 70-75 in them
@GraemeLowry-v9b
30 минут бұрын
What about a simple non return valve in your old filler lines.
Пікірлер: 52