The boom on the backhoe could be fixed where the pin is lose, it would need to be line bored and welded back, then bored back to the diameter of the pin to make it tight again
@michaelmactavish4445
4 ай бұрын
the deere dealers sure is ripp off for corn flakes lol thats wounder we bought a kubota plus great deal and $2,500 off wich is nice
@ChrisBalser-pd1lv
4 ай бұрын
I knew you was gonna save something you never use all new parts you get lol 😂
@nathanbrodeur
4 ай бұрын
Bill if I remember correctly when you would have the thumb on the backhoe when the bucket was new it also was flexing the bucket cutting edge and cracking the weld from the cutting edge to the bottom of the bucket cause I remember you had re welded it a few times before the bucket side to the cutting edge failed on that rock
@wysurvivor
4 ай бұрын
Hello Bill, from northern Wyoming.
@johnmilner7603
4 ай бұрын
If I had a sloppy hole I would mig weld it then run a drill bit or die grinder bit to reshape the hole.
@joelground7557
4 ай бұрын
Hey Bill, you might ask around and see if there’s a guy up there around you that can line bore it on the machine. Around here, there’s a couple guys that will come to you and do it all where the machine sets. They might know someone at John Deere or one of the other construction equipment dealers.
@iggymac3473
4 ай бұрын
Need the arm line bored ? upside down ? glad you seen it
@Kronkus36Outdoors
4 ай бұрын
Can you use AR plating to construct new bucket brackets ? I would think the pin holes wouldnt wear as bad with AR plate
@Oldyellor
4 ай бұрын
Haha there ya go trying to trick us again. The wing arms were installed upside down , they arch up ward not downwards but you knew that
@mgman71
Ай бұрын
Those pins use press in grease zerks
@hyundia1
4 ай бұрын
up side down bill lol
@rockfosg
4 ай бұрын
Line boring or expander bolts/pins
@charlestaylor2480
4 ай бұрын
Have you tried to line bore everything and put in new bushings
@MARKLOCKWOOD2012
4 ай бұрын
Bucket 🪣 Died or kicked the bucket 😅
@MARKLOCKWOOD2012
4 ай бұрын
wallard out the pin hole. you know if sleeved the hole to take up the slack Macgyvered it right as rain. Because the slop is going get worse. Or fit or make a bushing to take up the difference. No parts available unless they want you to replace the whole arm. The only other option to is to drill out the whole sleeve weld in a new one Knowing you build a new one. Because Jd don’t make 110 tlb nor do they make or made to replace the pin hole 🕳️ Or goop up the hole with Jb weld then sand it till the pin gets tighter then before replacing the pin shove a ton on grease. Going to have to do more work to keep her going cause to replace the machine you won’t cuss on camera unless you do a doot noise. Cheaper as i said fix the pin hole. 🕳️
@windzer
4 ай бұрын
the guy made the bucket wrong there needs to be bosses on one side that the main pins slide thru and the bosses need to have a hole drilled thru it so u can run a bolt thru it and the main pin locking the pin from rotating inside the bucket holes. right now your pins are able to spin around in the bucket holes and thats wearing it out cause it basically nothing there to grease it. also u can get shims just like the ones that fell out on you u need more shim to take all the side to side slop cause that wears things out faster too.
@billstmaxx
4 ай бұрын
That's what happens when you go cheap I guess
@windzer
4 ай бұрын
@@billstmaxx u can have the holes in the bucket bored out and bushings put in it .then just make a couple bosses out of thick wall pipe and weld them on yourself the bucket shouldn't be that big a deal if u got a machinist close by
@michaelmactavish4445
4 ай бұрын
ouch $4.00 for 1 grease fitting so $8.00 for 2 holy seems the deere dealers taking customers for ride lol its sames here and only $0.59 cents each at my kubota dealer @@billstmaxx
@johnmilner7603
4 ай бұрын
Don’t forget there is a right and wrong way to install snap rings.
@HughzieTube
4 ай бұрын
Could you not buy a mag drill, weld the holes up on the bucket, then mag drill them back out to pin size? You would probably need to weld a shelf onto the bucket ears for the drill to sit on, then cut it off once you were done. Dirt Perfect had a video up a few years ago where he line bored his boom pins on his Ex. Its a bit of a process that needs some specialised kit.
@620JK
4 ай бұрын
Anyone else see the horse and cow
@mattive6212
4 ай бұрын
U can Mak a bushing
@billstmaxx
4 ай бұрын
if i had a lathe
@MARKLOCKWOOD2012
4 ай бұрын
Any body kind enough to please send me The Jd bucket of paper shop towels?? I don’t see them in my neck of the woods You can get rolls and a card board box. The bucket would be a lot sturdier
@mattive6212
4 ай бұрын
U hav a welder will fix that
@johnw6389
4 ай бұрын
You put them upside wrong
@billstmaxx
4 ай бұрын
keep watching :)
@michaelmactavish4445
4 ай бұрын
remembered fixing that bucket on the video@@billstmaxx
Пікірлер: 31