as someone that lives in the states, im extremely jealous that you guys have this car
@earthislevel
2 ай бұрын
There is a 'conspiracy' which goes along the lines of "USA shut Australian Ford and Holden (GM) down because they were upstaging the US flagship models". I tend to think this is bordering on the line of truth.
@smoothwalrus9354
Жыл бұрын
Kowabunga, dude! That's so great that you got it done in the end. Love it.
@mg74xbgt
Жыл бұрын
Great Effort. Did this 7 years ago to my FG with way more shall we say Budget parts.....and made 540 rwhp on 14psi. Engine was still quite happy at that level , however the box fried after one good pass at Willowbank. Way less clutches in the atmo box. 12.0@120 mph though. Was tuned by Forced in Toowoomba. On a side note I managed to get the car to run a 13.6 over 1/4 when it was atmo 😁
@fgmods
Жыл бұрын
That's awesome. The NA motors can take and make a lot more than people give them credit for.
@mg74xbgt
Жыл бұрын
@@fgmods All I did was to swap in a 3.45 diff centre and extractors plus free flowing/noisy exhaust and got a mail order tune from BP and it ran a 13.6 atmo. The Vid is on my channel if you go back about 7 years. Doing the turbo conversion with a T70 Master Power turbo was fun though !!
@HRPMProjects
Жыл бұрын
mighty impressive result on the NA bottom end with some minor supporting mods! just amazing! what a journey! so happy for you mate well done!!
@OGTroll
Жыл бұрын
Me and my misses recently bought her old Falcon back and engine swapped it with a fresh low ks bf series 2 na motor seing this makes the temptation of turbocharging it so much more haha
@TheGarageGamer86
9 ай бұрын
Subbed, nice video man! I especially love the part where you show the route up to Townsville and there's like 100 lots of road works, that's peak Australia right there!!
@MrEnormous874
Жыл бұрын
Great content, I’m another one with dreams of converting my na territory for the last few years!! Pls upload a 6month review when u get a chance. Good luck buddy🤟
@sollydogg
3 ай бұрын
Thats actually insane 350kw hell yeahh
@310ingyou2
Жыл бұрын
Smashed it. Car looks dope.sounds great congrats on your evolution! 🎉
@thisguycalledalex
9 ай бұрын
I’ve done the drive from Townsville to brisbane. What a trip ✌️
@MrKrueger88
Жыл бұрын
So happy you've built the dream car you'd been wanting for so long . I built an 85 supra into a turbo engined beast years ago . Now I've an fgx xr6 and thinking a turbo or supercharger conversion would be fun to do . Cheers , and thanks for a great channel 😅🔥💯
@jetthammond7811
Жыл бұрын
This helps along mate, thanks
@lightemupson
Жыл бұрын
Sounds bloody insane !! I need an external gate so bad 🥲
@therig1339
Жыл бұрын
I watch pfi speed and they have been pushing pulsar turbos on plenty of hondas and they absolutely rip. Their technology and quality is really good. And I'm seeing more and more people running them
@fgmods
Жыл бұрын
Pulsar have pretty much become the standard for Falcon builds now. Very reliable turbos.
@CAIDMASTEROFPYRO
Жыл бұрын
Na zf is surprisingly stout, my mates got one in his 550kw g6e, it hates life and slips 3rd-4th if you shift on power but it hasn't failed catastrophically.. Turbo or better yet built box is the go though, mine makes 410kw and the standard turbo zf hasn't missed a beat
@yourmatejay
Жыл бұрын
So glad to see it boosted man!! Well done 👏👏👏
@dontbugmepleasethanks
Жыл бұрын
Bro I’ve been waiting for this for so many years finally!!!
@Reuel_Media
Жыл бұрын
Nicely put together video mate 👍 enjoyed watching
@Mr_Driftstar
Жыл бұрын
Well done 👍
@Nzbackyard-spars
9 ай бұрын
Good video
@ryanumbers1499
Жыл бұрын
Nice but.. i did this 2 years ago running 98 and 8 psi and i make 305 RWK with an UN OPENED FG NA engine, stock exhaust internal gate just a cooler kit and air box, still going strong too :)
@fgmods
Жыл бұрын
That's a great result for a Falcon with no work! If you're comparing results don't forget where I specifically said we didn't want to push the car too far because the gearbox needed to survive the 1400Km trip back to Brisbane.
@Cody-rn4tb
Жыл бұрын
entertaining and funny video and decent power from N/A barra. keep it up
@shaunkelly5994
Жыл бұрын
Love the video man . I had same pulser and gate set up housing had to been machined to fit . Just a fyi😊😊
@civilizedsavage360
Жыл бұрын
Big Congats, I have been wondering if you were gonna get there, well done 👍
@joeysykes566
Жыл бұрын
Awesome build mate
@tamagage2206
10 ай бұрын
What a nice car
@vkkaoskaotix6633
Жыл бұрын
out of curiosity how much ball park figures, did it end up costing? from parts to finish? been looking into it a fair bit recently, this got me even more keen todo it! cheers for the vid man
@gman7949
7 ай бұрын
Cool build mate. Well done.
@SAMMYNICOLE-l4h
6 ай бұрын
Great video
@vincekara9446
Жыл бұрын
Congrats mate. Awesome result. I have a BF Turbo stock and am really tempted to unleash. However i know it'll become a money pit. But then the smile on your face when you push it
@fgmods
Жыл бұрын
Money in exchange for happiness is well worth it
@wobblysauce
Жыл бұрын
Build, break, repeat
@vincekara9446
Жыл бұрын
@wobblysauce My brother has got a VL turbo built from the ground up. It goes like a cut cat, but most of its life is spent at the mechanics due to breakages. Has spent working overtime to pay for upgrades.
@wobblysauce
Жыл бұрын
@@vincekara9446 Or dial it back a tad to gain the reliability... hahaha what am I talking about.
@vincekara9446
Жыл бұрын
@@wobblysauce That is the magic formula. $ vs power vs reliability.
@MaXpeedingRods_Coop
Жыл бұрын
keep you work mate
@SPWILLY
Жыл бұрын
Inspiration mate
@rubberbandman2540
Жыл бұрын
good shit well done lads
@Oni____
Жыл бұрын
Nah, being in SA with Na+T dreams on a 5 speed is soul crushing. Might have to bite the bullet and just get a xr6 turbo :(
@williametheridge9694
3 ай бұрын
What do you mean about being in SA?
@tturi2
Жыл бұрын
matts a great guy
@troycreely9344
3 ай бұрын
Would love to see a cost breakdown on this build. Turbo parts
@FluffyRaT
Жыл бұрын
Holy fucking shitballs, the power!!!!
@gbg.freddie3192
5 ай бұрын
Can you list down the parts I need to get to turbo charge my NA falcon ? Cheers man ! Love the vid 🔥
@kostaki1944
Жыл бұрын
👌
@stockie6
Жыл бұрын
Great informal video, however It would've also been nice to add the cost of everything together, regardless still a great video. I am surprised that you haven't had an aftermarket zf heat exchanger installed as of yet, may of put you more on ease on the drive back. But wow 354kw is some serious power! That's enough to make anyone happy for a really long time.
@fgmods
Жыл бұрын
I’ll probably address the cost in a future video. I’m not done with it yet, so total cost will change. Trans cooler will come in the future. Wasn’t happy with the one I previously bought, so I didn’t install it.
@matthewwillshire4418
Жыл бұрын
End of the day its still faster and mor3 reliable then josh obriens fg ute 😂😂😂😂😂😂 good content josh 👌 #dontdriveonbeachs🎉
@maznir688
Жыл бұрын
what was the cost and parts needed? and labour
@hiluxmonstertruckgleno6276
3 ай бұрын
Nice build Factory stock ecu ??
@perthbeastzzzz4574
Жыл бұрын
should of used a green top barra
@nicholasdanielmalone
7 ай бұрын
Hey mate I’ve done a na+T conversation on my xr6 and for some reason I keep getting a engine light come on, I can get rid of it by disconnecting battery but then couple days later it comes back. I’ve got thoughts on it been o2 sensor seen I’ve put a big dump pipe and cat on it but not overly sure. Have you had any dramas like this. Any help would be appreciated
@wolfhound_4203
Жыл бұрын
welcome to tsv
@insolentchild6989
Жыл бұрын
How much does it cost generally to put a turbo in a falcon?
@DeanJackson-hu1dg
5 ай бұрын
I spilt my beer when the Corona episode came on
@lloydchristmas2326
Жыл бұрын
How did you drive it back to Brisbane being a full time e85 car ? And the turbo zf boxes aren’t anything special I blew mine at about the same power you have on your NA box ( if it’s still alive lol )
@fgmods
Жыл бұрын
The drive back was fine on 85. Just had to stop more regularly to be sure I didn’t run out hundreds of Ks from a united with E85. Fuel economy is only about 100Ks worse than before, give or take a bit.
@lloydchristmas2326
Жыл бұрын
@@fgmods lol I bet you had all the united servos fully mapped out before you started driving back !! Why’d you plumb the external gate back into the dump ? Screamer sounds way better
@itz_hux
Жыл бұрын
Matt should of sent you around the corner so I could of fix and painted your front bar😂
@fgmods
Жыл бұрын
Would have been good to fix it. It's a mess.
@lachlanscarrs7938
Жыл бұрын
how much did the build cost overall??
@fgmods
Жыл бұрын
I’ll address that in a future video. I’ve still got more I want to do, so the total cost will change soon.
@kers225abk2
Жыл бұрын
Why does no one ever say how much it costs? Its so annoying. Its such a simple question. He didn't ask how much once you've done more, we just wanna know how much for the parts and install 🤷♂️
@jarrod1687
Жыл бұрын
Congrats mate, if you had your time again would you just sell the na and bought a factory turbo? And have you installed / upgrades the trans cooler?
@fgmods
Жыл бұрын
Nah I’d never sell it. I’ve still spent less than I would have buying a factory turbo (unless it was a really clapped turbo) and I got to learn a lot from the guys at Elite and have fun doing the build along the way.
@jarrod1687
Жыл бұрын
Fair enough, bet it drives so well compared to the na
@MervynLake
Ай бұрын
Roughly how much did all that cost
@maple3953
Жыл бұрын
how much did the entire thing cost?
@johnevans2736
Жыл бұрын
Hey just watched your video and was wondering what the cost was as i am keen to do this to mine
@karlosgoldee1975
Ай бұрын
What did you do for loom and computer?
@rc70ys
Жыл бұрын
I would think it would be cheaper to have sold the NA and purchased a turbo one ready ? Great Video 😊
@fgmods
Жыл бұрын
I’ve still spent less than I would have on a factory turbo.
@danrobertson3846
9 ай бұрын
Do you know what fitting was tapped into the lower thermostat?
@andrewcook7346
Жыл бұрын
Bro makes as much at my factory turbo falcon, berry nice but idk if I'd be pushing then na rods much more then you are
@fgmods
Жыл бұрын
Nah they’re gonna get pushed a lot further.
@andrewcook7346
Жыл бұрын
@@fgmods your a brave man good luck keeping it together
@onlaptop6219
3 ай бұрын
Was that all the mods to the engine looking to turbo a stock na
@fgmods
3 ай бұрын
I have a more recent vid with the full parts list and cost breakdown
@glitchypoo
11 ай бұрын
I just got the 1k like let’s go I saw 999 so I had to
@kb-wk2mb
6 ай бұрын
How much was it parts and labour?
@JakeMinton
Жыл бұрын
Will you be doing a cost breakdown video?
@fgmods
Жыл бұрын
Yeah I'll do a full parts breakdown and cost video in the future
@cdoug4566
7 ай бұрын
Why go from all the way up to townsville to get it done?
@fgmods
7 ай бұрын
Because my friends own ELITE and I wanted to support them and show how incredible they are at what they do.
@cdoug4566
7 ай бұрын
@@fgmods Thats Awesome!!
@patrickfischer2253
Жыл бұрын
I say your car last weekend at QR for Cruise the Night. How did it go?
@fgmods
Жыл бұрын
Car ran like a dream all night.
@jamezxh
Жыл бұрын
Why not just buy a turbo FG to start with?
@stevecvntniko8271
11 ай бұрын
98 or e85 tune?
@djm2214
9 ай бұрын
Is your front bumper custom ?
@fgmods
8 ай бұрын
Yeah it is. Honestly wouldn’t recommend it. The join flexes too much and cracks all the time.
@pokedan6846
Жыл бұрын
Did I miss it or did you keep the na ecu and run a external boost controller?
@fgmods
8 ай бұрын
Yes it's the NA ECU and using the GFB electronic boost controller.
@chrisyoung4768
Жыл бұрын
Did you upgrade the injectors and pump?
@fgmods
Жыл бұрын
Yeah larger injectors and pump. In my “unboxing turbo parts” video I go over which ones.
@thewraith6360
3 ай бұрын
What can the stock FG barra motor take?
@fgmods
3 ай бұрын
There’s a lot of factors involved What fuel you’re using Timing Turbocharger There are a decent number of people who have gotten over 600HP on stock NA bottom end
@thewraith6360
3 ай бұрын
@@fgmods Nice im asking cause im in america and thinking about doing an FG longblock
@chriswilliams9551
Жыл бұрын
Is it still going strong
@fgmods
8 ай бұрын
It's been on 18/20 pounds for about 6 months now. Still going hard.
@levi-hi8og
Жыл бұрын
Not sure if u said in the video, but what exhaust did u get?
@fgmods
Жыл бұрын
ANTZ dump and cat, then an Xforce cat back
@careypatmore2576
Жыл бұрын
The second you turbocharged it it wasn't n/a
@samnz07
Жыл бұрын
Stock internals?
@fgmods
Жыл бұрын
Stock bottom end
@jackdawg4579
Жыл бұрын
you left out the most important part - what do you reckon the damage to your wallet was after all of that!
@fgmods
Жыл бұрын
I’ll address that in the future. There’s more to do so the total cost will change.
@anishchand4420
Жыл бұрын
Did you buy$ OEM Ford parts to Turbo your NA XR6 ?
@anishchand4420
Жыл бұрын
Sorry you didn't.
@Rileysaganster
Жыл бұрын
The fact that covid 19 shut states and it wasn’t Evan necessary…
@MrKrueger88
Жыл бұрын
No , because having it spread uncontrolled and hospitals overrun would have been great ... More deaths than necessary !!!
@Rileysaganster
Жыл бұрын
well covid was bad for babies and old people so why shut down states that cant afford to do it and local businesses. Too ?
Пікірлер: 132