This video (4yrs old) and another you did 2 years ago on Drape and Stamp have been fantastic for me. I am designing 2 houses on a site that is an irregular triangular shape - there's several boundary lines and setback lines PLUS the slope is down and across the site and will require several "cut and fill" locations and this video was totally a light bulb moment for me - thank you.
@PaulineFerguson
2 жыл бұрын
Thank you, I knew I'd seen the stamp tool (in your live terrain modelling vid) but this made it really clear and simple
@Volcano2021
4 жыл бұрын
Your explanations are perfect, thank you
@sharaazahmed7782
3 жыл бұрын
thank you so much, was struggling with this issue for a long time. very simple explanation 👍🏽
@emdearch
4 жыл бұрын
Quick & clean! Thanks. I've learned... Oh Yes.
@MrDagwood63
2 жыл бұрын
This is great! I have saved ....
@dharmagraphics-architects7363
Жыл бұрын
Hello! Aaron thanks for that review. I wondered if there's a way to grade the road more after it was draped; In order to level it out, as roads go?.
@jdcamc
4 жыл бұрын
I like your t-shirts...
@allenculuris8035
3 жыл бұрын
Very nice. Question please; how would one form a surface over a model? Like making a vacuum formed part or package. I was thinking DRAPE might work? Very good explanations Aaron
@fabdelap2971
4 жыл бұрын
Good afternoon. Nearly 5 pm where I live. Some ideas of model designs : the ISS, Delta IV rocket with its lunar orbiter, a drone (MAVIC air), etc... I have subscribed to your channel but I have never received any message! I try to listen to most of your live sessions. I learn a lot! How about a session on a rendering package? regards
@DaleClymens
3 жыл бұрын
Can you stamp a level (cross section) road that is following sloping terrain? You can drape the outline of course but can you level the road in between the draped edges?
@mpasquarella44
4 жыл бұрын
Aaron You did a Video before about importing a .jpeg for windows and resizing it to the figured dimension on the imported plan. Could you do a Video in a step by step way showing how to import a plan and trace over it using the shown dimensions on the imported plan. Thanks
@jame5j
4 жыл бұрын
There seems to be a gap in knowledge between the two videos, specifically how you went from a ‘from contours’ model to one with perfect quads...
@tricky2k
4 жыл бұрын
So the low volume of your mic is not exclusive to the live videos. Nice :)
@donsmith3167
4 жыл бұрын
sounded fine to me? Didn't notice it being low at all?
@AaronMakingStuff
4 жыл бұрын
tricky2k Just checked the volume of this and a few other videos against some other YT videos and the audios seems ok... please let me know if you are hearing a problem with any other videos on our page.
@tricky2k
4 жыл бұрын
Sound in your videos is always a tad low when compared with other videos in youtube, being live or not. Just do the test, open this video or one of the live streams and some other at the same time, you won't hear yourself. I mean, is not that important, it's the content what matters, but sometimes I forget to turn down the volume after watching your SU livestreams, then open some other video and it's quite a jumpscare :D :D
@Simon-Simon-Simon
3 жыл бұрын
why is it locked at 1000mm i CANT SEEM TO CHANGE VALUE
@briancampbell1413
4 жыл бұрын
With the stamp command, is there a way of determining what volume of material is either removed or added to the landscape?
@AaronMakingStuff
4 жыл бұрын
Brian Campbell If you Group the geometry and close it off (make a solid) the Entity Info will display the cubic size.
@briancampbell1413
4 жыл бұрын
Thanks Aaron
@2002makki
4 жыл бұрын
Hello Aaron How do you make the road stay level from side to side but following the curves of the valley (up and Down).
@stuartbillings2589
4 жыл бұрын
Yes, good question. Aaron?
@donsmith3167
4 жыл бұрын
that would be the Stamp command. it will leave your object flat and cut mesh to connect. Like the foundation he did on the left side where he cut down into the ground.
@peterthinks
4 жыл бұрын
Quads with three sides? Am I missing something?
@kbwfgg6400
3 жыл бұрын
Would have been helpful if you show how to draw in Plan view "how to get the road in the first place" instead of just quickly referring to it. So the search continues.
@SketchUp
3 жыл бұрын
Check your spam folder. If you subscribed, you can likely just log into SketchUp using the email and password you created when you purchased.
@AbhishekRana-kk4we
4 жыл бұрын
Sir, please give some tips for climbing wall design in skp. how I can make a profile in skp.
Пікірлер: 30