May God bless you! It's been a few weeks since I subscribed to your KZitem channel, and I've been following your videos. I'm delighted to see people like you making educational content that reaches 10 million individuals globally. I truly appreciate your hard work and the way you share your knowledge with us. To be clear, I've learned more in these few weeks than during my time at university. Thank you for your excellent teaching, and I look forward to seeing more of your videos.
@hugoballesteros3929
Жыл бұрын
I loved this video. It clearly teaches the difference with overload relays and MCB's which I was struggling with.
@mmysticmann
2 ай бұрын
Well explained! You should upload more and more.
@danielteyehuago1633
5 ай бұрын
Wow! This is video very informative and the best tutorial on the topic for me so far. I really appreciate it. Thanks for sharing it with us. Your ability to add the circuit diagram to your work makes you a top notch...
@danielteyehuago1633
5 ай бұрын
Wow! This is video very informative and the best tutorial on the topic for me so far. I really appreciate it. Thanks for sharing it with us.
@altavibration3602
9 ай бұрын
Thanks a lot ! great video and explanations ! from an electricity student from France
@erkaerdenebat9858
Ай бұрын
very thankful for your videos.
@sameedansar3552
11 ай бұрын
May God reward you
@youngmastersbeats
7 ай бұрын
These videos are great easy to understand keep them coming
@zackbryan3195
Жыл бұрын
Thank you. I have been studying to get my license by myself with study guides. I get some of the questions right but I didn't understand what the difference was.
@iskconbang
5 ай бұрын
Superb explanation in this video thank you sir.
@Tobirama-UchihaDestroyer
23 күн бұрын
What will be the result if i make it on a holding???
@user-vf7bt7un6z
9 ай бұрын
Thank you for your teaching us
@freelife9103
Жыл бұрын
Great video. Good job.
@PharmaEngineeringMech.Elec.
5 ай бұрын
Good Explain 👌
@FredHernacki
3 ай бұрын
What type of animation software you used to make this awesome video. Thanks
@Sevenhillssiri
6 ай бұрын
Wonderful
@lookingupwards8652
4 ай бұрын
I have a hotdog stand that im installing a on demand 120v continuous run water heater. It has a shutoff float for when the water supply tank gets low. How do I wire the float in?
@amirulnazreen1518
28 күн бұрын
Use contactor, connect the float switch in between phase and terminal A1 or A2 of the contactor, and your auto water pump is done to use
@MrMariobalotelli45
2 жыл бұрын
Thank you sir
@kowitikongili6077
Жыл бұрын
Great lessons,,,I learn alot,,,keep it burning
@ummachi4707
Жыл бұрын
Next vedio... Fully aoutomatic single phase motor with flote switch (including :protection divaces and manuval and hand switch)
@abderrahmaneadam6144
Жыл бұрын
well explained , orgonized m thank you very much
@Zulfiqar_786
Жыл бұрын
Very informative and learning video
@bigboykris2630
11 ай бұрын
This video is very well made👍
@amosmomombi5644
Жыл бұрын
Good analysis
@daltondelaney9534
9 ай бұрын
At 7:00 why can’t you just open the mcb to turn power off to the contractor coil? Why is an auxiliary contact block needed?
@chandrashekarazad23
Жыл бұрын
Thank You Sir.
@alessioschiavone3898
Жыл бұрын
very good. But I would had merged the buttons and hold contact start/stop in the cirquit
@sebastianovergara2443
10 ай бұрын
Great video, what 3D software was used to do the animation?
@llVIU
8 ай бұрын
no, they're all real components in a real room
@manikantavangavolu3201
Жыл бұрын
But we have already MPCB is available..then we can set amp settings
@paulmabeti9183
Жыл бұрын
What is the meaning of the symbols on the overload relay and those buttons
Пікірлер: 40