Great video, thanks for posting! About to attempt a 5.3 swap on a 68 Camaro for my daughters first car, this info is exactly what I needed!
@blindguysgarage
Жыл бұрын
Your welcome and thank you for watching if you have any questions or think I left somthing out let me know and I will help where I can also I think I said already but my car had a full f body accessory drive from a 98 camaro with ls1
@myoneblackfriend3151
Жыл бұрын
I would’ve save so much money by listening to you before I bought anything.😊
@blindguysgarage
Жыл бұрын
That is horrible never good when you have to spend a bunch of extra $ but thank you for watching
@Rowdy_Bikes
3 ай бұрын
Great information brother. I’m about to ls swap my 69 Camaro. Thank you Sir! Subscribed
@blindguysgarage
3 ай бұрын
You’re welcome and thank you for watching
@highostablegarage
Жыл бұрын
Sounds real good, can't wait to see it ripping around
@blindguysgarage
Жыл бұрын
The ls did sound good just wait until you hear the blower engine you will like it even as a ford guy all is Hot router can appreciate the sound of a blower
@aredondo27
Жыл бұрын
Greater video iv seen I have a 2003 Chevy Silverado complete donor truck but I want to swap into a 73 nova
@blindguysgarage
Жыл бұрын
That would be sweet if you have any questions s let me know
@sylvainverreault7010
11 ай бұрын
Awesome info for my next project!! Thanks
@blindguysgarage
11 ай бұрын
You’re welcome we are about to do it again 6.0 build for my 67 Camaro
@markbates7199
3 ай бұрын
You are great Thank you for your help
@blindguysgarage
3 ай бұрын
You’re welcome thank you for watching
@crcor2572
Жыл бұрын
Great video! Thanks for making it seem less intimidating. 👍
@blindguysgarage
Жыл бұрын
The LS is a very simple engine and the DOD delete side is also fairly simple as you see thank you for watching any help I can give I will gladly do
@melvintuckerjr2450
Жыл бұрын
Great video 👍 Blower looking good sitting in the Camaro 👍
@blindguysgarage
Жыл бұрын
Thank you and yes it dose been wanting to do that the hole time I had the car
@ozcorr909
Жыл бұрын
Great video very informative nice build 👍
@blindguysgarage
Жыл бұрын
@@ozcorr909 thank you again the blower setup will be coming next on the channel
@rudde67ssm62
7 ай бұрын
Go to a junkyard and get a 4th gen camaro or firebird radiator and the factory dual fans. A lot cheaper then buying aftermarket and direct boltin. I only paid $50 for all.
@blindguysgarage
7 ай бұрын
This is true and does work very well just does not always look the best in a classic car that has a bolt in installation not to mention not everyone has the ability to make brackets and make things look as nice as they could
@MrYz250fman
8 ай бұрын
Great video
@blindguysgarage
8 ай бұрын
Thank you very much
@mattpiper87
Жыл бұрын
Thank you for taking the time to make the video. Very informative. I’m in the process of doing the same. I’m wondering though will those headers clear the power steering box? I’m going to call speed engineering when I get a chance too. But thought maybe you may know?
@blindguysgarage
Жыл бұрын
Yes they fit perfict I have power steering on my 67 camaro and thy fit with no issues
@mattpiper87
Жыл бұрын
@@blindguysgarage thanks man!
@blindguysgarage
Жыл бұрын
@@mattpiper87 your welcome any time
@chasehayes9276
8 ай бұрын
Rounding up parts thanks for info
@6eightss
Жыл бұрын
Now I have no excuse to not start on my swap
@blindguysgarage
Жыл бұрын
Lol this is a good starting point there may and probble will be other small thing but this will get you started if you have any questions pleas ask I will help where I can
@6eightss
Жыл бұрын
@@blindguysgarage definitely a good starting point, thanks for sharing some knowledge.
@blindguysgarage
Жыл бұрын
@@6eightss your welcome
@johnlow4949
Жыл бұрын
Awesome info. Does that oil pan sit low to the floor and how close was it to the cross member? Im doing a swap on a 71 nova. Thanks for your time
@blindguysgarage
Жыл бұрын
The oil pan fit perfect as long as you use all sbc fram stands and engine mounts with LS adapter plates if you use big block frame stands and motor mounts you will have to put spacers behind the motor mount or under the frame stands so it won’t hit the lower crossmember
@johnm7265
Жыл бұрын
Does that wiring harness manage the charging system also? Doing a ls swap on a 68 nova trying to figure out what wiring ill need to keep and what I can get rid of
@blindguysgarage
Жыл бұрын
Yes it does it that’s another reason why I like doing the harness that way
@customjrod
8 ай бұрын
I'm going to do this swap on my 72 nova. A question I've got for you is, would you do a after market front subframe kit with new suspension and a rack and pinion, or would you just swap the manual steering for a power steering box and run after market control arms. Thanks for the video btw
@blindguysgarage
8 ай бұрын
I’ve done it both ways however I like factory subframe with aftermarket suspension such as ride Tech really good stuff
@customjrod
8 ай бұрын
@@blindguysgarage thanks man
@blindguysgarage
8 ай бұрын
@@customjrod Anytime any questions let me know
@walkerm4904
2 күн бұрын
should i update my rear too? its stock modded to posi track
@blindguysgarage
2 күн бұрын
It really depends on how you are going to drive the car and use it if just a toy that you drive every now and then and you just play and spend the tires here and there it will probably be fine if you’re going to put some sticky tires on it Wide tires as well it might be worth upgrading
@user-xd1ps9io3r
Жыл бұрын
Thanks so much great job I’m doing 69 Camaro my 2005 LS2 corvette is in the frame rolling ,not under body New Tremec T56 Mag ready to go in do you know how long stock drive Line will be and part numbers for radiator hose’s
@blindguysgarage
Жыл бұрын
I don’t how long the stock drop line would be I’m sorry however radiator hoses are used are these Radiator Hoses Upper Gates 24409 Will not work with truck water pump this car had a f body water pump from 98-02 camaro or firebird ls1. The hose come with a plastic Quick disconnect on one end cut it off close and it will fits perfectly Lower Continental D71244 It must be cut to fit as well I installed on radiator and then cut to fit on thermostat housing Heater loop Dayco 87653 If you don’t have a heater core This hose comes shaped as a J cut it to a U and install
@nacx_outburst8448
2 ай бұрын
Hey man are you using the stock ecu that came with the engine and it’s wiring harness with the harness you linked and also do you have another link or no where I can find the harness the link is no longer good :(
@blindguysgarage
2 ай бұрын
Yes, I will post you a link and yes, I use the factory ECU red and blue
@@blindguysgarage awesome man I really appreciate you thank you if I have any more questions I’ll be sure to ask you keep up the great content your helping a lot of us out man 💯‼️
@blindguysgarage
Ай бұрын
Thank you will do
@Mixer-uj9ik
2 ай бұрын
What about a t56 to 5.3? Flywheel clutch bearing?
@blindguysgarage
2 ай бұрын
They make a sbc/lt1 conversion, bushing, and clutch to just drop in place with or change the bell housing and use LS stuff
@tuukkakotipelto5056
9 ай бұрын
Apologies for what might be a dumbass question but are there exceptions when doing this to a 68 firebird and what should i keep an eye on. Also big thanks for taking the time to make this video
@blindguysgarage
9 ай бұрын
The first GEN Firebird 67 to 69 are basically the same as the camaro. if doing the swap my way use small block Chevy frame stands and stock small block Chevy engine mounts with the LS adapter plate. There is also a company called dirty dingo that makes a bolt in engine mount kit it just is a few dollars more than doing it this way. Either of these ways works great. As for headers oil pan transmission all works perfect and are the same for Camaro and Firebird. If you have a automatic transmission from the factory keep all the factory transmission shift linkage. It will bolt to a 4L 60 E or 700 R4 with just a minor adjustment in shift linkage. Hope this helps and if you have any other questions I am do my best to answer.
@tuukkakotipelto5056
9 ай бұрын
@@blindguysgarage holy shit didnt expect an answer so soon, thanks alot and all the best from Finland, this helps a ton
@blindguysgarage
9 ай бұрын
@@tuukkakotipelto5056 your welcome anytime
@cedricdeoan1214
Ай бұрын
I just swapped a 1968 Camaro and I got not crank no start what do you think is the problem
@blindguysgarage
Ай бұрын
If you have a no crank condition on a older car like that, it’s probably not getting power to the starter therefore it’s probably either a bad ignition switch or something is wrong in the main starter circuit possibly a neutral safety switch
@cedricdeoan1214
Ай бұрын
@@blindguysgarage it’s gotta be a neutral safety switch because the starter and ignition switch is new. So do I connect the 2 purple wires together to bypass the neutral safety switch. Its a 1968 Camaro ss
@blindguysgarage
Ай бұрын
@@cedricdeoan1214 to bypass the neutral safety switch take a 12 gauge piece of wire and loop it at the purple two pin connection should be under the dash either on the steering column or closer to the shifter in the floor
@darinr8895
8 ай бұрын
Could a Holley 12-300 EFI in tank conversion fuel pump be used instead of buying the whole tank kit?
@blindguysgarage
8 ай бұрын
That might work I have not done the swap using this setup
@darinr8895
8 ай бұрын
@@blindguysgarage Holley claims the pump is regulated at 58psi, does not require a return line and the sending unit will work with factory fuel gauge. I will be doing an LS swap over the winter and going over all of my options. Great video by the way.
@blindguysgarage
8 ай бұрын
@@darinr8895 thank you very much if this is the case it would be a good set up for someone with a nice factory tank or even aftermarket replacement
@ronaldrey8474
Жыл бұрын
Is there a brake pedal sensor for (2 plug or 4 plug) something for lock-up on torque converter ?
@blindguysgarage
Жыл бұрын
What I do is wire in a 5 pin relay if I don’t have a 4 pin brake switch and use the center pin on the relay end it out pin on the brake switch as the trigger power that way when not on the brakes The computer sees power when on the brakes it slips away from the center pin in the relay and the computer no longer sees power this is just one way of handling it but it works well
@ronaldrey8474
Жыл бұрын
@@blindguysgarage Holly smokes that's amazing thinking & I understand those directions better than 4 prong blah blah brake switch type. Does the voltage matter for the signal ? And I promise no more questions but sincerely THANK YOU.
@blindguysgarage
Жыл бұрын
@@ronaldrey8474 The voltage really doesn’t matter too much also if you are just working the system and don’t have the time to set up a relay just run that wire to power for the short term and all will work you just won’t have lock up until that is fixed yet it will run and drive OK. Also I don’t mind the questions anytime I can help just let me know and you’re very welcome
@geewitit185
10 ай бұрын
What about intake injectors and fuel rails throttle body
@blindguysgarage
10 ай бұрын
The factery ls1 ls6 and ls3 fit nice I have also used the fabricated aluminum intakes however you have to notch the hood for those to fit if you look at my more recant videos you will see a 69 camaro I just finished up with the aluminum intake set up
@hectorcervantes5462
Жыл бұрын
Question, are the LS engine mounts bolt on to the original mounts?
@blindguysgarage
Жыл бұрын
I’m not sure I understand the question but I will try and answer what I think you are asking. The ls swap adaptor comes with new bolts it is very simple and bolts to the block with 4 Allen head countersunk bolts. Then the standard sbc/bbc mount for your car will bolt to to the adaptor plate. There is multiple passions you can set the mount in. The most foword holes are for stock location if I rember right. I try and and use the second hole back to move the engine foword about 3/8 of a inch. Makes it nice for firewall clearance. I hope this helps answer your question. If not let me know and I will try again
@YoAdrian209
Жыл бұрын
Hey im new to the LS world but jyst purchased a 68 firebird with a 350. Would this also apply to my bird?
@blindguysgarage
Жыл бұрын
Yes make sure you are using camaro sbc engine mounts and sbc frame stands and you will be good to go
@denverfreeman7505
Жыл бұрын
Do you know what headers will fit with the Z Bar on the factory 4 speed cars.
@blindguysgarage
Жыл бұрын
I don’t but I also don’t thank the ls has a way to use the z bar without some aftermarket brackets
@denverfreeman7505
Жыл бұрын
@@blindguysgarage I have an aftermarket bracket. And the z bar is set up, I can use stock manifolds but wanted a set of long tube headers. I may have to have them built.
@blindguysgarage
Жыл бұрын
@@denverfreeman7505 I see I will post a short tomrrow with the header bolted to a ls engine so you can see it I think the speed engineering headers I was running would clear a z bar If used with aftermarket z bar bracket I will post vid and add a link to the comment here
@blindguysgarage
Жыл бұрын
@@denverfreeman7505 Z bar work wjth speed engineering swap headers??? #shorts #camaro #ls  kzitem.infoVTVdeeivCvs?feature=share
@1234Stocktrader
Жыл бұрын
Rear end swap?
@blindguysgarage
Жыл бұрын
My car has a 12 bolt in it now I am planing a 9 in for it but the 12 will be great
@seanschofield3391
Жыл бұрын
Any contact with power steering with that pan?
@blindguysgarage
Жыл бұрын
No all was good I used it on camaro and chevelle and both where fine
@seanschofield3391
Жыл бұрын
@@blindguysgarage how low does it hang? I’m doing a 6.0 swap into a 69 Firebird
@blindguysgarage
Жыл бұрын
@@seanschofield3391 it did not hang below the sub frame but if I rember Right it was just above it
@aredondo27
Жыл бұрын
Great video Do you have a instagram? This is going to help me do my 73 nova. I have a complete 2003 Silverado 2 Wheel donor truck. Im pull the motor n tran out of
@abennett56
Жыл бұрын
I can’t seem to find that lower hose anywhere. Who carries it?
@blindguysgarage
Жыл бұрын
I buy most of my parts through autozone lower hose d71244
Here is the link the hose is kinda wonky shaped but the bins make it nice around transmission lines and other things
@abennett56
Жыл бұрын
@@blindguysgarage Just picked it up. Thank you so much!
@blindguysgarage
Жыл бұрын
@@abennett56 your welcome any time
@Jp68camaro
Жыл бұрын
What about a Muncie 20
@blindguysgarage
Жыл бұрын
I am not sure let me see I will get back with you on that but for the trans it will bolt up fine not sure what you have have to do about the clutch
@blindguysgarage
Жыл бұрын
I here is a article on how to do so I know most people use a t56 with no issues but if I remember right the clutch release z bar is one of the biggest obstacles
Will a 4l60e fit without modifications to trans tunnel ?
@hectorcervantes5462
Жыл бұрын
Question, i have a running LS2 coupled with a T56 going into a 69 camaro. Can i install the whole thing together or do i split them apart? Im guessing i need to fabricate new whole for shifter? Can i still use the OE ECM? This is my first LS swap so i am trying to use what i have. Im not going high performace. I will be spending the money where i need it as far as parts. I appreciate your knowledge.
@blindguysgarage
Жыл бұрын
You should be able to go in from the top with no issues all togather make sure you have the right Oil pan and all sbc mounts and frame stands. it will drop right in as if it was a sbc I use the stock ECM in most cases and a aftermarket harness as it looks nicer and it’s easer to work with
@blindguysgarage
Жыл бұрын
Also do you have the throttle pedal and tech module from the car the engine and TRANS came from
@blindguysgarage
Жыл бұрын
Here is one of the harness that may help if you have the thrattle pedal and tac module www.ebay.com/itm/334533638265?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=iiksmpyeskw&sssrc=4429486&ssuid=8gTdxxS-TzS&var=&widget_ver=artemis&media=COPY
@hectorcervantes5462
Жыл бұрын
Not sure at the moment. I need to verify if the pedal and module were included. Will i need to cut a new hole for the shifter to fit or will i able to use the stock one?
@blindguysgarage
Жыл бұрын
@@hectorcervantes5462 every trans is a little diferant so it’s hard to say but I think you will have to move the hole back about 3 in but don’t know for sure
@marcanthonysuazo
Жыл бұрын
Everyone just forgets 5.7 alluminum block smh
@blindguysgarage
Жыл бұрын
Saves some weight but still fits the same I like the iron block tho just my preference gues it left over from the sbc days
@Jp68camaro
Жыл бұрын
You over heat a aluminum block and it’s trashed. Iron block can support boost better
@marcanthonysuazo
Жыл бұрын
@@Jp68camaro not everyone trying to boost
@Jp68camaro
Жыл бұрын
@@marcanthonysuazo true.. but iron handles head a little better that aluminum. But you are right aluminum is lighter but just keep your eye on the temp!
@blindguysgarage
Жыл бұрын
@@Jp68camaro I agree in both cases don’t overheat it and not everyone is hunting boost as I said I happen to be an iron block guy
@R-W-Germany
Жыл бұрын
Compared to you, WE are blind
@blindguysgarage
Жыл бұрын
I am legally blind and unfortunately have absolutely terrible vision not saying anything about who’s worse just know mine is really bad The reason the name BlindGuysGarage cam up is I am legally blonde as I said and my stepfather is blind in one eye so there it is BlindGuysGarage but thank you for watching
Пікірлер: 134