Really love the detailed logic and reasoning behind your actions, when I know why something is done it helps me understand what the final result should be.
@chrisE815
3 жыл бұрын
Great video! Mueller-Kueps 460 202 Thin Brake Caliper File works great too! Has a "chisel" end too for getting under the scaled rust.
@stephen6640
3 ай бұрын
Wow, who says you don't learn something new every day. That was a great illustration of how not doing something as "simple" as cleaning your hubs can cause you to fail runout by X7.
@maxcarter3413
3 жыл бұрын
Great video. It would be nice to have links to the tools demonstrated.
@jareddiamond6607
2 жыл бұрын
Google using words
@linadsenoj
2 жыл бұрын
OTC 8342 hub resurfacing Roloc sanding discs (usually use 80-100 grit brown). 3M ones work and seem to hold together well. I buy mostly 2", but always have 3" for certain hubs and calipers The purple strip and clean are good too. To save on shop supplies use a steel bristle brush (straight and cone) and a fine burr bit (Careful not to take any core material off!) with either a drill or die grinder to work most of the rust off, saving the rolocs for final finish.
@BobBlarneystone
Жыл бұрын
Great job, and quality service to your customer. That's how business always should be done.
@johnjoseph7382
2 жыл бұрын
This is a great video. I think only half of the mechanics out there even bother cleaning the hub face and less than 25 percent check for run out and do a finishing on-car lathe to get it within spec.
@Casket_Music
Жыл бұрын
What is run out?
@philtheheaterguy951
Жыл бұрын
@@Casket_Music😂😂😂😂😂😂😂😂
@gearheadautomotivel.l.c.5476
5 жыл бұрын
Great video y'all. Such an important part of a quality brake job. Could you also take a torch and run an oxidizing flame to help get that heavy scale to just pop off or at least loosen up? Being careful of course not to cook the bearing or fatigue the spindle itself mind you. Perhaps that's too risky but I thought it might be another option. Thanks as always for your time making these videos!
@jankuyper8353
Жыл бұрын
Take an old file and grind the end flat ...makes an awesome scraper
@matthewwithey5859
5 жыл бұрын
Super great video, great work on the hub there. Great info. Have a mighty fine day.
@johnboyjr21
3 жыл бұрын
Sounds like it could just use a new hub altogether
@chevalierdeloccident5949
Жыл бұрын
Right... hahashahahahah
@zolox3525
3 жыл бұрын
Agree with everything he said. I'm lazy, I would look to change to a new hub and use a nice thin layer of synthetic paste to prevent the issue.
@disturbator
10 ай бұрын
Can u use silicone-teflon paste?
@mikeeustice4452
4 жыл бұрын
When dealing with scale like that as we have in new york warm it up with a torch just to the point where the rust will pop off on its own . don't heat it to much but at the right temp it will pop then go in with your disks
@porkstamina
4 жыл бұрын
Thanks for the video, was considering using a needle scaler but wasn't sure if that was safe on the hub.
@soyews
3 жыл бұрын
Thanks for the video. I had never thought to clean the hub to improve braking performance. I have the rims off for power coating. Guess I will be using the needle scaler and a thin coat of high heat paint.
@cameronduff884
9 ай бұрын
...thanks Ray, you're the bestos...
@buddyboy4x44
3 жыл бұрын
Interesting you said it was one of the worst you have seen. I see lots of Jeep models with what looks like lots of premature rust. I long since decided Jeeps (Chryslers?) are rust buckets.
@bladder1010
11 ай бұрын
Excellent. What he said makes a lot of sense.
@darrenporsch
Жыл бұрын
An air angle grinder is much better spins at much higher RPM than those drills. That's what I use and I live in New York we get plenty of rust and road salt
@NhoyBarangay
4 жыл бұрын
I would have those studs removed by a Pneumatic Hammer. Grind the entire Hub with a Hub Grinder. That's how I would do it.
@jacklumbar7061
2 жыл бұрын
And all the makers had to do was galvanize the thing and none of this would be necessary.
@barrysmith8078
2 жыл бұрын
Is it worth painting these hubs with heavy duty heat resistant paint for added protection or is that not an option?
@johnjoseph7382
2 жыл бұрын
just use a slight coat of Fluid Film and you'll be good to go
@nemo5335
5 жыл бұрын
could you put some sort of grease or anti-sieze on the hub to prevent this from happening again?
@mustangenthusiast
4 жыл бұрын
3M copper anti seize brake lube
@escottn
4 жыл бұрын
Antiseize or a small amount of marine grease.
@johnjoseph7382
2 жыл бұрын
Fluid Film
@jeff2385
3 жыл бұрын
Total noob here, but what type of tool uses roloc disc's? Also what grit number should you use? Thanks!
@johnjoseph7382
2 жыл бұрын
3m hub cleaning kit
@kayleedavenport5052
3 жыл бұрын
I never heard any mention of replacing the hub....
@owengune
2 жыл бұрын
Great video
@rubbertoea8088
3 жыл бұрын
Great video!!
@Eger118877
5 ай бұрын
What color of roloc should I use?
@Romulan112
Жыл бұрын
I removed the cv joint and there was a lot of rust inside the hub, all around the perimeter. Anyone know what kind of tool to get the rust off inside that circle?
@Kobayashhi
4 жыл бұрын
Oddly satisfying.
@kikigem2952
9 ай бұрын
Why not refinish the hub with a high temp caliper paint at that final stage to since its so cleaned up? Is that not something recommended?
@SincerityAF
5 ай бұрын
With the tight seal needed between metal, having a painted surfaces might compromise that. Plus when it scratches that's going to cause other problems
@AppalachianPatriot
Жыл бұрын
Clean the hub and spray OSPHO on it. Personally I would have replaced the hub.
@rikunaskali7408
3 жыл бұрын
I haven't seen hubs that clean on any of my cars I've owned :D Road salt and proper winters aren't cool.
@viplegaleducation1292
4 жыл бұрын
What book do I use for runout specs, please, if you do not mind ? I donot see specs for a lot of vehicles on Mitchel1.
@user-bp3we5tz1o
3 ай бұрын
two thousandths runout is excessive in my opinion.
@stephenyoutubin4476
3 жыл бұрын
Plot twist, the hub bearing was toast and had to be replaced anyway.
@garrettguffey2195
2 жыл бұрын
needle scaler still peens the surface of the hub flange, i use a carbide scraper, its tedious, but works well.
@golightly209
Жыл бұрын
Links to the brushes
@ASEWorldClassTech
9 ай бұрын
Rip to whoever has to do that Wheel Bearing.....
@colombo0413
2 жыл бұрын
Good video but very biased on the sanding tool you barely used the first tool and then gave a tiny cut away then started with the second tool and did a longer cut away as you worked that one for longer to get that scaled rust
@JamesNathanielVlogs
4 жыл бұрын
How does it even happen
@mikejenniferaloisi788
3 жыл бұрын
What kind of roloc discs would one use for this?
@johnjoseph7382
2 жыл бұрын
3m has a hub cleaning kit, you just have to buy the disks seperately, it's the most popular, you can use a drill or an angle grinder
@Dangerkiller-D
4 жыл бұрын
What happens if all your wheel hubs are like this?
@kyhamoge
Жыл бұрын
You clean them all! 🤷🏻♂️
@philtheheaterguy951
Жыл бұрын
The other option is to refrain from buying a JEEP!
@KobaBlack113
5 жыл бұрын
Some guys have never ever did a proper brake job.
@Bigshoots86
3 жыл бұрын
Couldn't you just soak it in some gas or some shit?
Пікірлер: 65