Who would dislike this video? Maybe it was the auto shop that will now not get my business because I can do the work myself.
@CraigMarolf
3 жыл бұрын
People may have disliked because there are better/safer ways of removing and replacing a stud. I think this is fine but for OCD types they may opt for using a less harsh method (joint separator, for example).
@Strong_UP_Calvins_zombie
2 жыл бұрын
WAKA WAKA!!!
@jordanartinial4593
2 жыл бұрын
Maybe people tried it and it wasn't as easy as it seems
@chonkyloreraccoon3686
2 жыл бұрын
Bets it has to do with tools; Either they didn’t have most of the tools used, or they used more specified tools exclusively made for this job
@CrimsonHarpLovegoddess_1
Жыл бұрын
If you add a larger washer; such as a 27mm and insert your regular washer, let's say uts a 19mm, you can Insert the 27mm backwards through the bold and slide the smaller one inside. 😉 also It works just like a replacement washer and i just used wd40 and hand cranked it with my torque wrench
@seananderson8497
7 ай бұрын
Wow, I was just quoted $1,700 to replace 10 of these, this is basic level skill required. Thanks for the helpful video.
@fourteenants
6 ай бұрын
robbery lol
@moonlander03
5 ай бұрын
I wouldn’t call it basic skills.. any skill is ez when u know it .. but not when u don’t 😂😂😂😂😂
@davidseifferleinfilm
2 ай бұрын
I just had a seized lug nut on a spinning stud. 3 hours with my buddies help. Luckily we had all the tools. Because wow. What a trip that was. Covered in metal slivers. This was not easy
@tredogzs
Ай бұрын
Thats every single mech job
@petertimpson9378
18 күн бұрын
I would!. These studs were not years old as you can see they pop out in 1 or 2 hits.
@alexbaez2478
3 жыл бұрын
Watched this video last night, woke up this morning and replaced my broken lug stud. Thanks a ton!
@tcwgaming5280
3 жыл бұрын
Quick tip! You can use a very large socket (about 30mm) and fit it over the stud backwards to act as a removal tool. Simply put a nut on the stud after placing the larger socket and ensure you have enough room inside the larger socket for a smaller socket. Tighten up the nut until you can’t anymore and you’ve installed your wheel stud!
@olial8342
Жыл бұрын
f'n genius, my guy.. didn't realize it, but I got two of 32 mil sockets!! I hope it works when I replace some studs!
@kurmit0076
Жыл бұрын
Lmao it won’t get stuck in the socket square?
@abousidi75
Жыл бұрын
Smart! Thank you
@azureblue29
5 ай бұрын
I just tried this and it works great. I had a 1 1/2" socket lying around. Thanks! 🙏🏻
@btarb242
4 ай бұрын
better than nothing, but not quite the same as the proper tool, which has a bearing on the back side to reduce friction and chance of spinning and ruining the splines/hub.
@chellechapa6524
3 жыл бұрын
Good advice but I'd like to give you a tip/trick for the next time you need to remove both the caliper & bracket. You can use a C clamp to depress the caliper pistons just enough so that you can take out the 2 bolts that hold the caliper bracket on. Doing this let's you slide the bracket, caliper & pads off the rotor all together. It saves a little time when replacing studs or hub & bearing. Daddy taught this girl well. 👍😁
@benjaminblack5888
2 жыл бұрын
And remember to protect the master cylinder by simply opening fill cap before using C clamps.
@tjsmith9449
2 жыл бұрын
@f c exploding, if the brake fluid level is high, when you compress the piston all that fluid has no where to go
@leeson6321
2 жыл бұрын
@rusty nail my understanding was always just that removing the fill cap before pressing your calipers in keeps the lines and caliper free of air getting inside, eliminating the need to bleed them. This actually does work. The brakes feel spongy as hell at first but pumping the pedal and refilling the calipers with fluid returns them to proper operation. If you were going to press all 4 calipers at the same time, common sense tells us that once your fill reservoir is full of fluid if the cap remains in place there’s going to be that point that the calipers stop pressing in at which point if you tried forced them to press something somewhere would rupture but I’d be quicker to guess this would occur at one of the other calipers. Now that I’ve typed all that i realized that @Benjamin Black is the one who this reply probably should have been addressed to. My bad, can’t just erase it though.
@danburch9989
2 жыл бұрын
To all the commenters about the master cylinder. It's impossible to "explode" or ruptue any part of the system unless there's a weak point already. It would already have ruptured during normal driving due to the high fluid pressures during braking. Secondly, as brakes wear, the fluid level drops in the master cylinder. When you compress the wheel cylinders, you are pushing that fluid back into the empty space in the master cylinder. The brake system is a sealed system. Unless you open a brake line, there should be no air in the system. The brakes will feel spongy after installing the calipers but it will go away after a few pumps of the brake pedal as the fluid in the master cylinder get pumped back into the lines and calipers. None of what I stated applies to cheap Chinese master cylinders. Some don't have a bladder in the master cylinder cover to take up the empty space.
@amzarnacht6710
Жыл бұрын
@rusty nail You won't 'explode' the master cylinder, but you could easily rupture a seal somewhere. Luckily, most modern cars actually have a vent in the brake fluid reservoir so overpressure has somewhere to go before damaging internal components.
@forestMog
3 жыл бұрын
Clear as day. No BS. I am so glad you included the washer/grease tip. Thank you.
@ramtek2702
2 жыл бұрын
The grease serves no purpose except to make a mess.
@Thebrothaisback
4 ай бұрын
What about making sure that the washers dont stick together?@@ramtek2702
@sed6
2 жыл бұрын
Thanks man! I was ready to pull the axle on my son's truck. This saved me tons of time and worked like a charm! I didn't have the fancy conical shaped washer so I just used the lug nut itself, it worked fine no damage. Thanks again!
@TrentBigW
3 жыл бұрын
Thanks for the video. Replacing my wife's transmission showed me that she's missing a stud. I'll be replacing that today thanks to you.
@busystuff23yearsago15
2 жыл бұрын
Wtf
@Doxxi
2 жыл бұрын
@@busystuff23yearsago15 I lawld
@spitefuljay
7 ай бұрын
Can replace a trans but not a stud?😂
@TrentBigW
7 ай бұрын
Never had to do it before. I KZitem'd the trans swap as well. 🤷
@spitefuljay
7 ай бұрын
@@TrentBigW Very well. That’s impressive for a trans haha
@robertmadueno2732
2 жыл бұрын
Great vid. You explained it well and best part you actually show what you are doing and what you did. Before and after view. Idk why more people don't do this like you did. Great vid!
@DeenoBDS
11 ай бұрын
so we had to cut the heads off the studs to remove them, the cut half the heads off the new ones to get them in. having a spacer there to get the new studs in was such a great idea it helped a lot. couldnt have done it without this video
@Leo137156
Жыл бұрын
Big thanks man. I had to stop once I removed the rotor assembly and the brake calipers because I did not know how to remove the stud. You made it so easy. Thanks a lot!
@glenishii2022
2 жыл бұрын
Wow. A lot simpler than I thought it would be. Thanks for the video!
@TheMuffinMan-wr3yb
4 жыл бұрын
A method I came up with to set the studs is just get the stud in place, slide a couple close ended wrenches over the stud and start tightening while applying pressure to the wrenches to keep pressure on the head of the stud so it doesnt spin.
@joseserna6277
10 ай бұрын
Damn I have a rounded stud head
@michaelc565
2 жыл бұрын
Thanks for the tip on the stud install tool! Last time I needed to replace a stud was about 10 years ago and I fumbled through it successfully. Your guide will make it much smoother this time.
@robertmccully2792
10 ай бұрын
Those studs came out easy, mine are extremely tight.
@nekoisme2703
9 ай бұрын
I have a project truck with a bent stud, it's not horrible but it's a little noticeable, this video is great, very in depth and good explanation, thanks
@thecapitalalliance
11 ай бұрын
Great video! Thank you. One addition: remember to chemically remove all grease from the newly installed stud.
@FernandoLopez-ph8is
3 жыл бұрын
Mr. Hines, seriously, Thank You, You made it look easy ...
@Amberdawnn76
3 жыл бұрын
But was it?
@forgotten4006
2 ай бұрын
Thanks, i dont have the right bit to get the rotor off but i managed to squeeze them out and the new ones in. Now i just need a million washers to get them fully in
@robertmulready7573
4 жыл бұрын
Thank you - so glad I found this video , made my day.
@jamesodiomu9079
Жыл бұрын
Thank you, much appreciated, so Educative,much love from Uganda Kampala 🇺🇬
@Oneffunes
2 жыл бұрын
The corn. You did good you got straight to the point and no playing around.
@WiPri0371
4 жыл бұрын
Just bought the Lisle tool. Hard to believe there are kits that cost over $200 to do this. But if you have bad aim, use a soft metal hammer to remove the stud. Like a brass hammer.
@micamckay9719
10 ай бұрын
Thank you so much for this video. So straight forward and concise. You could teach anyone to work on vehicles.
@JohnnysSpeedShop
5 жыл бұрын
Mate...found your channel a few week ago...great stuff...very well done.....👍👍👍👍
@AaronHinesAuto
5 жыл бұрын
thank you!!
@ElBrodito
4 жыл бұрын
I just want to say THANK YOU !! The past three years I have been looking for a permanent solution without success. Apple told me that they cannot do anything because my MacBook was a vintage model (2011), although it is s great computer. With your help, it is working just fine. Again, thanks. All the best !!!
@mikehd3904
3 жыл бұрын
Be replacing 8 tomorrow... hope they come out that easy.
@Username-ng8jy
3 жыл бұрын
Use mapp gas. Don’t get to crazy on the hammering. May damage wheel bearings. Just FYI.
@Username-ng8jy
3 жыл бұрын
I’ve made a rig with a c clamp. Basically use the old lug nut. Seat it all the way possible with a gap. Then take a piece of wood and place it on the nut. Use two c clamps and tighten. It should gently pus the stud out.
@mikehd3904
3 жыл бұрын
Ah dude take the axle right out and pressing them out was real easy, bro has a truck shop so the right tools made the difference👍
@mikehd3904
3 жыл бұрын
@Bones McGillicuddyhe sure the fuck didn't do it,I did , it's called right tools and work smarter ,not harder so whose the idiot here?
@km-gi4lw
5 ай бұрын
Well done , quick work , all tools and pieces prepared for the job thanks
@mikelisowski7619
5 жыл бұрын
If there was video I needed to see more this would be it. Thank you!
@askaboutRudyV
2 жыл бұрын
Thanks Aaron, I will be doing this tomorrow, as today Indid an oil change and tire rotation.
@noeunkim7451
4 жыл бұрын
Thank you for your teaching!
@cosmicbrambleclawv2
3 жыл бұрын
Thank you for this, I have 2 busted studs on my 76 El Camino driver side front wheel, they broke off almost clean with the hub annoyingly enough
@trevorgriffith8994
3 жыл бұрын
Gud video gud advice. i have one stud to replace will do it myself. Easy n simple but garages always make out the job is harder than what it is.
@NeverEnoughPyro40
Жыл бұрын
Some cars are a lot harder than the smart ass, Try replacing a front wheel stud on a front wheel drive import! Also it is harder on his El Camino because you have to remove the front bearings and rotor, All vehicles are different that is why prices can vary by $100s
@Meche697
3 жыл бұрын
How do you keep the new stud from stripping when your installing?
@randymiller3583
Жыл бұрын
Nice job, Thank for the cool video, we just broke one today changing our struts on the Ford Expedition and this really helps with question I had
@marcgascoigne3896
2 жыл бұрын
Please tell people to take the grease off the new stud. Seems obvious but not to everyone.
@merlinnwolffe8534
3 жыл бұрын
I had to completely remove the axle to replace the studs on my 2003 F-150. Then the studs had to be pressed out on a 12 ton press because They wouldn't budge with a few hits from a hammer. This guy is lucky.
@CaptainThirdGen
2 жыл бұрын
rust also complicates things. to get the front studs out of my rusty 2002 sierra it took many hits with the sledge for the studs to finally come out. Had to remove them so I could use a bolt to pull the old wheel hub off.
@joshowens2062
8 ай бұрын
Doing the good lords work. Great video. Well done!
@Hebsparks
4 жыл бұрын
Awesome! Thank you for making this seemingly tough thing easy.
@whitney3277
3 жыл бұрын
I feel confident that I can do this myself and I'm a girl.. 🙄 he explained this beautifully 🥰
@AJ-nw8vk
9 ай бұрын
Thanks for the quick and easy method
@crittixisme
6 ай бұрын
This video is so well put together but anyone else notice the Ubolts on the truck
@tibob69
5 күн бұрын
Great video. Quick question : do you absolutely need power tools to replace the stud or just a ratchet with a long bar might do the job ?
@ironman1518.
7 ай бұрын
Thank you for advice on the tool!! Had Never seen one of those!!
@jesseswan5598
2 ай бұрын
Awesome video! Thank you.
@ILoveChanelLynn
Жыл бұрын
Thank you so much for your video!!!!
@and7976
3 жыл бұрын
Two questions: 1- Why didn't you remove the entire brake (two bolts holding the bracket) instead of removing it in two pieces? 2- Why don't you just put the studs in place and put the rotor+wheel and tighten the nuts? since it will automatically pull the studs into place without the adapter? Thank you
@odubb45
3 жыл бұрын
I would want to make sure the studs are fully seated too, before I put the rotor and wheel on. I think it would take more than 100 ft. lbs. of torque to pull those studs in. I don't want to puts the wheel on, then have the wheel start wobbling because the studs were not fully seated.
@mattstivers1683
2 жыл бұрын
I wish I would have watched the whole video before pulling the threads on 2 of my spline type lug nuts. I watched the first half thinking it wasn't for my 2015 GMC sierra. Live and learn lol
@bertodj4814
3 жыл бұрын
you and chrisfix have the same voice and the same skills i like your channel
@AaronHinesAuto
3 жыл бұрын
Thank you for the support!
@CP-sh4qv
9 ай бұрын
Great video, clear and concise. Thank you
@Prince.Prince1999
6 ай бұрын
Complete! Excellent! Thanks!
@ballstoyou33
2 жыл бұрын
Lol holy shit a great KZitem video !! I was scared of using the washers and didn’t want a 30 min job to turn into a day long thing but that shit really worked !!! Got my moms jeep nice and fixed back on the road they didn’t even realize I had the car apart loll
@AaronHinesAuto
2 жыл бұрын
Awesome! It’s a good feeling when it all works out! Glad to hear u got it fixed and thanks for the compliment.
@NeverEnoughPyro40
Жыл бұрын
The only part you didn’t show and edited out was when you pulled the stud through using the washers and it got stuck because your washer wasn’t quite big enough!
@douglaswesserling6378
7 ай бұрын
Thanks man. This was super useful. Well done. Subscribed.
@davidjsouth231
2 жыл бұрын
2013 Ford Escape Titanium. Really don’t want to have studs replaced but I can’t get the lug nuts off because they’re pretty roughed up. Didn’t realize that when we bought the vehicle
@julianc.6589
2 жыл бұрын
fantastic work brotha appreciate it
@amzarnacht6710
Жыл бұрын
Question: I encountered a vehicle where all of the lugs spun freely while on the studs (i.e. the studs were no longer secure in the hub). How do you get the lugs off in such case?
@richardmcelroy6574
3 жыл бұрын
With all the loose socked out there at garage sale why not use a 50 cent snap-on. Dont know how it will work as i just came in frim the cold but will try and your washer method and see how it works. Thanks for the ideas
@maddog88
3 жыл бұрын
I assume I can replace the calipers as they were without the need to bleed them?
@darnellwillis4450
Ай бұрын
Great job
@ajr9914
3 жыл бұрын
Would using anti-seize on wheel studs cause the lug nuts to come off?
@JohnBradydoesstuff
Жыл бұрын
This has been super helpful. Thank you!!
@thapelorashilo8032
3 жыл бұрын
Very easy and understandable..tnx man
@jesusmejia1334
2 жыл бұрын
Good video and awesome tips I will be using this information at work.
@petertimpson9378
18 күн бұрын
How about old ones that won't pop out like the new ones you show here??
@KoiAquaponics
3 жыл бұрын
Nice video, simple and straight forward
@rcthomas6925
Жыл бұрын
Thank you. My Chevy Aveo does not let me back out or insert the new stud.
@charlesw3120
Жыл бұрын
Excellent video.
@ianhutchinson3635
2 жыл бұрын
Thanks Aaron, very helpful
@ttrapp6303
3 ай бұрын
Common reason why is some people put the lugs on with the impact inside of hand first then impact or 4lug wrench
@cd5781
3 жыл бұрын
Good video with some grest tips. What's missing is what to when one stud snaps off while tightening a lug nut on it, but will Not pull out from the hub. On the rear left of my 08 RAV4, one stud is somehow caught in the hub. I can rotate n jiggle it, but not pull it out, and now have a lug nut on it enough that I can only see ~1/4 inch of the bolt, so no angle to cut it. And no access from behind, of course. Any suggestions?
@ScreamingEagleFTW
2 жыл бұрын
no danger in just pounding them out? isnt there a tool or way to press them out? Im afraid I will brake the hub flange. Is that realistic for me to be concerned about that?
@just_your_localguard9612
8 ай бұрын
alot easier then expected tbh
@crazycowdogs9830
4 ай бұрын
Anyone watching this : Make sure you get all grease and oil off lug studs or you will over torque them and possibly snap them off again!
@nneo100
2 жыл бұрын
I love you man!!! Thanks for the video!!!!
@tammiebeckwith6558
2 жыл бұрын
Thank you very much for your time and help
@ThealaSildorian
4 жыл бұрын
Awesome. My ex-mechanic damaged one of my studs to get me to pay for work I didn't need. I'm going to save the hundred bucks or so and do it myself.
@azlan856
4 жыл бұрын
Yes. Helped lots. Thanks
@kelsteaart9363
2 жыл бұрын
I have to replace my studd, and this helps a lot. But I think I have to replace the hub too because the stud is stripped and spinning. Do you have a video on that?
@nightmarishhappenings
Жыл бұрын
Very informative video! Only one more thing to say, Hold on to your lug nuts it's time for an overhaul! 🤣🤣🤣
@axelbonilla5181
Жыл бұрын
Loads of help thank you bro
@Alexander-rn7mw
2 жыл бұрын
Great tips never knew about the washers and grease trick thank you for sharing that you get a like
@larryclover9809
3 жыл бұрын
great video, thanks for helping the ignorant
@chrispittman4042
Жыл бұрын
Thanks for the video! Do you have any suggestions if the tire is still on?
@artdogg50
9 ай бұрын
Great work!
@bubblehead7680
2 жыл бұрын
That socket set isn't available anymore. Any other suggestions?
@meshachfoster749
Жыл бұрын
Love the content man subscribed
@pedrominaya8400
8 ай бұрын
nice video
@Ilovemetalworking
3 жыл бұрын
Car we just bought day of the tire blew out so as we where taking off the lug nuts to put the spare on we found someone had impacted the piss out of 3 of the nuts practically welding the lug nuts to the studs. They snapped immediately as soon as pressure was applied to remove them
@w0rm45
7 ай бұрын
Who else was eyeing that caliper at 4:42? Dude almost had to replace a brake line and bleed the system.
@hdwnzjurncusmnfk
2 ай бұрын
Dude my balls shriveled up and went back into my body when I saw that
@wellnessotr
6 ай бұрын
Awesome! Thank you!
@TheGaryNinja
Жыл бұрын
Hey will this work on any car? I might need to do this on my Nissan car
@michaelbell8347
Жыл бұрын
Love how the rotor just falls off. My dodge 2500 they are seized on lol
@davycornell8715
6 ай бұрын
Why wont my studs spin? Like to get it lined up with the hole thats there to pull it out. I can almost get 1 out, but its not spinning to get the other 4...
@WH6FQE
Жыл бұрын
I have to replace the rear wheel studs on a 1990 Chevy K3500 1-ton dully and I can not find instructions anywhere for the rear. I was able to get the front replaced but I dont even know where to start on the rear as this rear end doesnt look like anything anyone has made a video for.
@NhoyBarangay
4 жыл бұрын
Is it true that using a Pneumatic Hammer on those studs could damage the wheel hub bearing assembly?
@kennethgilbertdds7249
4 жыл бұрын
I was wondering if that's what happened with the Chevy stud. Broken due to air hammer placement strategy.
@danytrejo7930
4 жыл бұрын
Nhoy Barangay we use them all the time, its absolutely fine as long as you know how to use them
@MurderSheWrote-
2 жыл бұрын
2 of my studs got pushed in. And everytime i drive it makes a really loud screeching noise. Is the wheel bearing fucked? Do i need to replace it or just replace the lug nuts?
@chrisjason6546
Жыл бұрын
What about your rotor screw holding it down
@michaelbright1569
Жыл бұрын
Thank you
@thusoselebi1608
2 жыл бұрын
wow that was easy, I will do it myself. Thanks
@pekomsmink
4 жыл бұрын
Good work very explanatory
@paulhojnacki1287
3 жыл бұрын
How would you do this if you can only jack up one tire and can’t spin the bearing
Пікірлер: 300