I was trying to demonstrate how fast the motor would charge a battery for very low voltage when an unexpected large back EMF killed the driver circuit.
I came for a BOOM but left with only questions and a reevaluation of my time management.
@mykedoes4099
Ай бұрын
Boom!
@simonilett998
Ай бұрын
WTF Did I just watch??🤣 👇
@markrix
Ай бұрын
Its spinning, muhahaha, me precious!! Spin!!! I have no idea wth your trying to accomplish here. 🎉 Spin on!
@make425
27 күн бұрын
@@markrix trying to make efficient motors. Thanks for watching thanks for the comment.
@ThePneumanicHunter
Ай бұрын
Hmm looks similar to Ed’s sweet sixteen.
@make425
27 күн бұрын
@@ThePneumanicHunter physical mass does change the equation.
@windpowerandmore6310
Ай бұрын
Did you have that charge controller connected to the output of the driver then to the battery? If so that's what happened because its not letting the backspike through which fried the Mosfet
@make425
27 күн бұрын
@@windpowerandmore6310 no, the charge controller is on the isolated L2s and L3s. There's no rectification on the driver circuit. But the back EMF battery.
@make425
27 күн бұрын
@@windpowerandmore6310 and it's happened before. It be pounding a battery and boom. Could the driver coil be pushing back on it's off cycle to much? I never thought of collecting half cycle from the driver circuit.
@windpowerandmore6310
27 күн бұрын
@make425 I think the gate fried if you had the resistor in that I sent in the circuit board. You have the right resistor in it now just monitor the heat on that resistor and adjust it to more resistance if getting warm or lower resistor a hair if stays cool. That resistor is key to having max efficiency with different input voltages. Seems you have it working pretty good now bud
@make425
26 күн бұрын
@@windpowerandmore6310thanks for replying buddy. Question though. If I want to run 36 volt. What do I need to do. It gets smoking hot when I do 3 battery's in series Do I need to do anything with the two wires that are twisted together?.
@windpowerandmore6310
26 күн бұрын
@make425 you just need to put a resistor with more ohms try 3k ohms
@A13tech
Ай бұрын
another perpetuum mobile crap ? jeeez youtube is drunk today or what.
@make425
27 күн бұрын
@@A13tech it's more about building a super-efficient motor. Very nice torque and power for less than 6 watts of electricity. The rotor weighs over 20 lb itself. But thank you for the comment and thank you for watching.
@A13tech
27 күн бұрын
@@make425 What is super efficient ? It is a rottary machine with a lot of looses in friction and winding impedance. Does not matter how many poles. Very close to very efficient are nowadays Xiaomi EV motors.
@zephyrlyon6678
Ай бұрын
Also lad I would recommend using some Heat shrink wrap so that your wiring is more safe for you and generally less likely to injury you and if anything was moved that touch's the bare wiring may cause a short circuit and cause a possible fire which to avoid that possibility better, which you put electrical tape on it I can see, but still heat shrink wrap is recommended for this.
@make425
27 күн бұрын
@@zephyrlyon6678 I agree, most of the wires that you see are the output coils. Not much current. The input side from the driver circuit is good. Thanks for watching and thanks for the comment.
@zephyrlyon6678
27 күн бұрын
@@make425 Of Course.
@richbl_channel
Ай бұрын
Huh?
@JamesBrown-oo8gz
Ай бұрын
It ran out of magnetic Flux fluid.
@make425
27 күн бұрын
@@JamesBrown-oo8gz I gave her all she had captain 😁
@mototola86
Ай бұрын
You ran out of electricity. What is that piece of crap
Пікірлер: 23