Great video, thank you! For anyone with dishwasher not draining issues, first thing to check is the screen or filter, then check hose and sump for blockage, I disconnected hose at sink, stuck a funnel in it and used shop vac to suck water through. Also check flow switch to make sure it's not stuck closed, it's usually visible in bottom of dishwasher. Check new garbage disposal to make sure Knockout was removed and if not draining completely google siphon gap and see if that might be your issue. Mine was a combination of issues and I just hate to see anybody buy a pump without checking these other things. Also prior to ordering, pump, you can disconnect it reconnect the power leads, select cancel or drain and make sure the impeller works. If it doesn't, use a tick tester to make sure the leads have voltage because if voltage isn't being sent, there is some type of control panel/mother board issue. Hope it helps...
@Appliancevideo
3 жыл бұрын
Great question, if you have a more technical question that our parts department cannot answer, you can search our over 17,000 answered questions free at our website www.ApplianceVideo.com under our Repair Help section. You can also call our parts department at 1-800-830-5465 and they can give you help 7-days A week ,or search at www.SaveMoreOnParts.com .
@emadr1
2 жыл бұрын
Your comment definitely help, my issue is that I'm not getting power signal from the computer!
@emadr1
2 жыл бұрын
I actually bought the pump and realized it was not the pump 🥺
@sptrsttradr4918
2 жыл бұрын
@@emadr1 Did you check the float switch? It should be able to move up and down freely to tell the machine there is water that needs to be pumped out. And or that the wires are connected to it underneath. Keep trying and hopefully you'll get it!
@maryrahmat9277
5 жыл бұрын
Thanks for sharing your knowledge! We have a similar DW (KitchenAid). A piece of glass was behind the impeller, and with your video we were able to clear it out. Very helpful video!
@Appliancevideo
4 жыл бұрын
Thanks for your response, we are glad we could help. Our library of over 5,700 videos are currently helping over 1.6 million people like you every MONTH. Please help us by subscribing to our KZitem channel, or post our website www.ApplianceVideo.com to your Facebook page, Twitter, Instagram or any other social media sites. Your support will help us keep producing more free quality videos.
@marcusdavis1609
5 жыл бұрын
Slide a cookie sheet under the pump before removing to catch all of the remaining water...saves cleanup time! If it won’t fit under the pump, place it as close as possible to the drain hose and remove it, directing the draining water onto the cookie sheet.
@Appliancevideo
5 жыл бұрын
Thanks for your response, we are glad we could help. Our library of over 5,700 videos are currently helping over 1.6 million people like you every MONTH. Please help us by subscribing to our KZitem channel, or post our website www.ApplianceVideo.com to your Facebook page, Twitter, Instagram or any other social media sites. Your support will help us keep producing more free quality videos.
@glloyd9707
3 жыл бұрын
Eat all the cookies first because they get soggy and dont taste as nice after a pump dump.
@jccarreira320
4 жыл бұрын
Piece of glass in mine. Made short work of it thanks to your video thanks.
@Appliancevideo
4 жыл бұрын
Nice work! thanks for your response, we are glad we could help. Our library of over 5,900 videos are currently helping over 1.6 million people like you every MONTH. Please help us by subscribing to our KZitem channel, or post our website www.ApplianceVideo.com to your Facebook page, Twitter, Instagram or any other social media sites. Your support will help us keep producing more free quality videos.
@hannahssong
4 жыл бұрын
great video instruction!! took me 10 min. to replace my drain pump after watching your video. thank you so much!!!
@Appliancevideo
4 жыл бұрын
Glad it helped. Thanks for your response, we are glad we could help. Our library of over 5,900 videos are currently helping over 1.6 million people like you every MONTH. Please help us by subscribing to our KZitem channel, or post our website www.ApplianceVideo.com to your Facebook page, Twitter, Instagram or any other social media sites. Your support will help us keep producing more free quality videos.
@rkolkovich
6 жыл бұрын
Thanks for the video, especially how to take off the pump. Saved me a service call. Had a small chicken bone stuck in the pumps motor.
@Appliancevideo
6 жыл бұрын
Thank you for your positive response, we are glad we could help. Please help us by subscribing to our KZitem channel or post our website www.ApplianceVideo.com on your Facebook page.
@jccarreira320
4 жыл бұрын
I had glass, don’t even know how it passed the filter in the basin. Unless it slipped in when I removed the filter screen for cleaning one time. This video was great though.
@birgitteinsiedl726
7 жыл бұрын
Hatte Probleme den Deckel der Ablaufpumpe richtig einzusetzen.Dank Papa-E,war dies kein Problem mehr.Super!!!!!
@Appliancevideo
7 жыл бұрын
Thank you for your positive response, we are glad we could help. Please help us by subscribing to our KZitem channel or post our website www.ApplianceVideo.com on your Facebook page. We want to let your friends & family know how our FREE videos can help them. Or you can support our parts department at 1-800-830-5465 and our parts website www.SaveMoreOnparts.com . This is the only way we can continue to post free videos and help over 1-million people per month like you repair their own appliances. We also have thousands of more quality videos on all major appliances made by our factory trained technicians at www.ApplianceVideo.com .
@Sandylowlead-x7r
Жыл бұрын
Thank you, very informative, 10 min fix!
@dawidcooper7788
2 жыл бұрын
You are incredibly clear!
@MechsDelCarribe
5 жыл бұрын
man you really helped me out, great video straight up exactly step by step what I needed to know
@Appliancevideo
5 жыл бұрын
Thanks for your response, we are glad we could help. Our library of over 5,700 videos are currently helping over 1.6 million people like you every MONTH. Please help us by subscribing to our KZitem channel, or post our website www.ApplianceVideo.com to your Facebook page, Twitter, Instagram or any other social media sites. Your support will help us keep producing more free quality videos.
@raybohn7
3 жыл бұрын
Best instruction I have seen. Thanks
@Appliancevideo
3 жыл бұрын
Thanks for your response, we are glad we could help. Our library of over 5,900 videos are currently helping over 1.6 million people like you every MONTH. Please help us by subscribing to our KZitem channel, or post our website www.ApplianceVideo.com to your Facebook page, Twitter, Instagram or any other social media sites. Your support will help us keep producing more free quality videos.
@jackholland7627
2 ай бұрын
Not sure i understood the comment on putting vegetable oil in dishwasher? How does this help? Why not rinse dishes in sink ?
@MOstix13
5 жыл бұрын
Awesome video! Thanks very much for the help!
@Appliancevideo
5 жыл бұрын
Thanks for your response, we are glad we could help. Our library of over 5,700 videos are currently helping over 1.6 million people like you every MONTH. Please help us by subscribing to our KZitem channel, or post our website www.ApplianceVideo.com to your Facebook page, Twitter, Instagram or any other social media sites. Your support will help us keep producing more free quality videos.
@e30m31989
4 жыл бұрын
Fixed mine! Yay!! I replaced the pump and it still would not drain. No blockages and the machine (Maytag) ran through it's cycles, just would not drain. **Here's the fix for: Maytag Model MDB4949/plus many other brands Remove the exterior door cover not the entire door, there are roughly 8 screws. The selection (buttons) panel clips in; unfasten. Be careful not to break the tabs that hold it in place. It's a rather tight fit. Simply disconnect the selection panel harness which connects to the control unit (the brains/computer). Note, only need to disconnect from the selection panel. Wait a moment and reconnect. BINGO! Up and running just like day one. That is all it took. Turns out my old pump was good after testing it on the bench. These machines are like computers and sometimes need a reset, nothing more. I sure hope this helps a lot of you out there in a similar bind. P.S. Maytag/Whirlpool know nothing about this. Spoke to tech support and got no where. They offered to send a tech for $115 just to look at it. Ha!
@Appliancevideo
4 жыл бұрын
Thanks for your response, we are glad we could help. Our library of over 5,700 videos are currently helping over 1.6 million people like you every MONTH. Please help us by subscribing to our KZitem channel, or post our website www.ApplianceVideo.com to your Facebook page, Twitter, Instagram or any other social media sites. Your support will help us keep producing more free quality videos.
@raybohn7
3 жыл бұрын
I used all the tips and eliminated everything except a clogged hose. A 10 ft snake took care of it. Yuck, must have been a 6 inch clog based on what came out. The filtering system seems to be capable of eliminating most particles. Not sure what built up in there- mostly grease?
@Appliancevideo
3 жыл бұрын
Great question, if you have a more technical question that our parts department cannot answer, you can search our over 17,000 answered questions free at our website www.ApplianceVideo.com under our Repair Help section. You can also call our parts department at 1-800-830-5465 and they can give you help 7-days A week ,or search at www.SaveMoreOnParts.com .
@billzhang709
Жыл бұрын
I have the same problem here. Just have some water left at the end of cycle. But if the pump has problem, wouldn't it stop draining completely? How come only left the last bit of water in the unit? Please help me understand.
@shamsahsan9251
9 жыл бұрын
Very helpful, thank you.
@Appliancevideo
9 жыл бұрын
+Shams Ahsan Thanks for your positive comment. We are glad we could help resolve your issue and hopefully saved you money. Please help us provide more videos to our site by subscribing to our KZitem page or posting our www.appliancevideo.com/ website on your Facebook or Twitter account. Our factory authorized technician’s also daily provide free professional Repair Help to people like you to help solve their appliance problems. You also have the option to email a factory service technician with a question at www.appliancevideo.com/repair-help/ . If you need of parts for your major appliance, we have over 5-million parts in stock at savemoreonparts.com/ . Thanks in advance for supporting us. So email us if you have any other questions our videos cannot resolve. Thanks for your support in advance. Matt, Ace Appliance service technician.
@gervilleharlequin994
6 жыл бұрын
Great video. I got the same dishwasher. Not sure what the problem is. It won't drain at the end of the cycle but when I press the cancel/ drain button it drains. I do have to press it 2 or 3 times for it to drain completely.
@Appliancevideo
6 жыл бұрын
Great question, if you have a more technical question that our parts department cannot answer, our technicians are answering all questions at our website at www.ApplianceVideo.com under our Repair Help section. You can also call our parts department at 1-800-830-5465 and they can give you help 7-days A week Mon-Sat . You can also search at www.SaveMoreOnParts.com 7- days a week.
@buckster2575
Жыл бұрын
Probably the blades on the pump that help get the water out broke. Mine does the same thing you have to hit it a couple times for its empty. I have a new pump coming that's probably what happened.
@heathermcgowen2890
5 жыл бұрын
What would be the next thing to look at if we replaced the drain pump. It still is not draining
@Appliancevideo
5 жыл бұрын
Great question, if you have a more technical question that our parts department cannot answer, our technicians are answering all questions at our website at www.ApplianceVideo.com under our Repair Help section. You can also call our parts department at 1-800-830-5465 and they can give you help 7-days A week Monday -Sunday, or search at --www.SaveMoreOnParts.com-- 24 hours 7- days A week.
@mkd3b
5 жыл бұрын
clogged drain hoses
@e30m31989
4 жыл бұрын
I hope you didn't spend money on this! Fixed mine! Yay!! I replaced the pump and it still would not drain. No blockages and the machine (Maytag) ran through it's cycles, just would not drain. **Here's the fix for: Maytag Model MDB4949/plus many other brands Remove the exterior door cover not the entire door, there are roughly 8 screws. The selection (buttons) panel clips in; unfasten. Be careful not to break the tabs that hold it in place. It's a rather tight fit. Simply disconnect the selection panel harness which connects to the control unit (the brains/computer). Note, only need to disconnect from the selection panel. Wait a moment and reconnect. BINGO! Up and running just like day one. That is all it took. Turns out my old pump was good after testing it on the bench. These machines are like computers and sometimes need a reset, nothing more. I sure hope this helps a lot of you out there in a similar bind. P.S. Maytag/Whirlpool know nothing about this. Spoke to tech support and got no where. They offered to send a tech for $115 just to look at it. Ha!
@zachbolinger6963
3 жыл бұрын
I just did a drain pump replacement and it's leaking. It's a European brand but the pump looks similar to the one in this video. I've seen recommendations to apply silicon grease, dish soap, or rinsing agent to the O-ring before installing the replacement. Any thoughts? The replacement part is not the exact same, but I ordered it from the manufacturer after supplying my model and serial number.
@Appliancevideo
3 жыл бұрын
Great question, if you have a more technical question that our parts department cannot answer, you can search our over 17,000 answered questions free at our website www.ApplianceVideo.com under our Repair Help section. You can also call our parts department at 1-800-830-5465 and they can give you help 7-days A week ,or search at www.SaveMoreOnParts.com .
@gotacopy821
9 жыл бұрын
Very good videos. How do I know after taking out my water drain pump is actually no good. Mine doesn't seem stuck. It moves but seem springing when it moves . Just doesn't free flow. Is that normal
@ThePatriotsBrother
6 жыл бұрын
Yup
@msaeed72
6 жыл бұрын
Yes, that’s normal, magnet in motor is preventing the free motion.
@lindsayday770
5 жыл бұрын
Yes that is normal. Saw it on another video.
@Appliancevideo
4 жыл бұрын
Thanks for your response, we are glad we could help. Our library of over 5,700 videos are currently helping over 1.6 million people like you every MONTH. Please help us by subscribing to our KZitem channel, or post our website www.ApplianceVideo.com to your Facebook page, Twitter, Instagram or any other social media sites. Your support will help us keep producing more free quality videos.
@Kthutton1
6 жыл бұрын
Question: Before taking old pump out, the cycle was running. I found a jam in the rotor which I took out and re- installed old pump. Not only did it not work, the dishwasher won't run now.
@Appliancevideo
6 жыл бұрын
Great question, if you have a more technical question that our parts department cannot answer, our technicians are answering all questions at our website at www.ApplianceVideo.com under our Repair Help section. You can also call our parts department at 1-800-830-5465 and they can give you help 7-days A week Monday -Sunday, or search at --www.SaveMoreOnParts.com-- 24 hours 7- days A week.
@Kthutton1
6 жыл бұрын
ApplianceVideo.com thanks. i have a jam in the line!the electric pin to the washer itself poppedout!
@pboix68
3 жыл бұрын
Great, do you know the part number of the clips?
@Appliancevideo
3 жыл бұрын
Thanks for your response, we are glad we could help. Our library of over 5,900 videos are currently helping over 1.6 million people like you every MONTH. Please help us by subscribing to our KZitem channel, or post our website www.ApplianceVideo.com to your Facebook page, Twitter, Instagram or any other social media sites. Your support will help us keep producing more free quality videos.
@edcicoria
6 жыл бұрын
Why did he leave the bottom rack in while he sucked the water out?
@Appliancevideo
6 жыл бұрын
Great question, you can call our parts department at 1-800-830-5465 and they can give you help 6-days A week Mon-Sat . You can also search at www.SaveMoreOnParts.com 7- days a week. If you have a more technical question that our parts department cannot answer, our technicians are answering all questions at our website at www.ApplianceVideo.com under our Repair Help section. We have over 6,000 common questions and answers that you can easily search through by your model number, appliance make, problem or error codes, and It’s completely free to search through our question & answer library. There is a very good chance you question is already answered there.
@allenpurdybayvalleyrealest7939
7 жыл бұрын
I have exactly the same DW and everything is good EXCEPT removing the pump. Are there some tabs or locking parts which require depressing first, or do I just "muscle" it counter clockwise?
@Appliancevideo
7 жыл бұрын
Great question, you can call our parts department at 1-800-830-5465 and they can give you help 6-days A week Mon-Sat . You can also search at www.SaveMoreOnParts.com 7- days a week. If you have a more technical question that our parts department cannot answer, our technicians are answering all questions at our website at www.ApplianceVideo.com under our Repair Help section. We have over 4,000 common questions and answers that you can easily search through by your model number, appliance make, and problem or error codes, and It’s free to search through our question & answer library.
@petertimpson9378
7 жыл бұрын
Allen Purdy Bay Valley Real Estate I have the same DW also and have the same draining problem. When I took my pump off, yes, you just turn it counter clockwise, it moved fine, meaning no pieces of broken glass or anything else keeping it from moving. Don't forget that clip holding the wire. My problem is with float valve and I'm just looking for something on that.
@stainless0521
7 жыл бұрын
On Maytags you have to press a locking tab!
@ThePatriotsBrother
6 жыл бұрын
There is always a locking tab you must depress before turning it
@e30m31989
4 жыл бұрын
I replaced the pump on my 2 years old Maytag. It still will not drain. Goes through full cycle but will not drain. Checked for blockage, there is none. What is the next thing that could be considered the problem?
@Appliancevideo
4 жыл бұрын
Great question, if you have a more technical question that our parts department cannot answer, you can search our over 10,000 answered questions free at our website www.ApplianceVideo.com under our Repair Help section. You can also call our parts department at 1-800-830-5465 and they can give you help 7-days A week Monday -Saturday, or search at --www.SaveMoreOnParts.com-- 24 hours 7- days A week.
@lecovio
3 жыл бұрын
What can cause it to drain manually but not automatically at the end of the cycle???
@Appliancevideo
3 жыл бұрын
Great question, if you have a more technical question that our parts department cannot answer, you can search our over 17,000 answered questions free at our website www.ApplianceVideo.com under our Repair Help section. You can also call our parts department at 1-800-830-5465 and they can give you help 7-days A week ,or search at www.SaveMoreOnParts.com .
@Airmeddriver
Жыл бұрын
Why didn’t you show what was wrong with the old one
@petertimpson9378
7 жыл бұрын
My Whirlpool DW drains some of the water out. I can hear it draining under my sink. When I removed the pump, it does spin freely and when the power is connected it does spin when it is put in "drain" mode. Could there be a problem with the float valve? I have moved that around and it would drain fine for a couple of cycles but then that stops and it won't drain again.
@Appliancevideo
7 жыл бұрын
Great question, you can call our parts department at 1-800-830-5465 and they can give you help 6-days A week Mon-Sat . You can also search at www.SaveMoreOnParts.com 7- days a week. If you have a more technical question that our parts department cannot answer, our technicians are answering all questions at our website at www.ApplianceVideo.com under our Repair Help section. We have over 6,000 common questions and answers that you can easily search through by your model number, appliance make, problem or error codes, and It’s completely free to search through our question & answer library. There is a very good chance you question is already answered there.
@ThePatriotsBrother
6 жыл бұрын
The float valve has nothing to do with the draining sequence. Just because your drain motor is spinning doesn't mean that isn't the problem. Make sure the impeller BLADES are all attached (and not broken or missing) on your drain pump. But most of the time a drain pump will still spin, but if there is a blockage in the drain line, it wont be strong enough to break through the clog. It'll just spin and spin. You have to find the clog.
@dtony1964
5 жыл бұрын
Question. There is water at the bottom of the DW at the end of the cycle I can get the water to drain manually be pressing cancel, however. Is this still a bad pump or something else??
@Appliancevideo
5 жыл бұрын
Great question, if you have a more technical question that our parts department cannot answer, you can search our over 10,000 answered questions free at our website www.ApplianceVideo.com under our Repair Help section. You can also call our parts department at 1-800-830-5465 and they can give you help 6-days A week Monday -Saturday, or search at www.SaveMoreOnParts.com 24 hours 7- days A week.
@Lord-of-the-Noble-throne
2 жыл бұрын
I replaced the pump and still there is water at end of cycle.
@lindseystyles5232
4 жыл бұрын
How did you know it was the pump that was bad?
@Appliancevideo
4 жыл бұрын
Great question, if you have a more technical question that our parts department cannot answer, you can search our over 17,000 answered questions free at our website www.ApplianceVideo.com under our Repair Help section. You can also call our parts department at 1-800-830-5465 and they can give you help 7-days A week ,or search at www.SaveMoreOnParts.com .
@doodar21
3 жыл бұрын
Replaced both Drain Pump and Diverter in a whirlpool and still doesn't drain ????
@Appliancevideo
3 жыл бұрын
Great question, if you have a more technical question that our parts department cannot answer, you can search our over 17,000 answered questions free at our website www.ApplianceVideo.com under our Repair Help section. You can also call our parts department at 1-800-830-5465 and they can give you help 7-days A week ,or search at www.SaveMoreOnParts.com .
@ryanlavine1405
7 жыл бұрын
Maybe could've ff through the vacuuming...
@Appliancevideo
7 жыл бұрын
Anyone can FF through it .
@LightningSpeed64
5 жыл бұрын
The vacuuming was the best part! I think he sucked up a dead mouse at 6:15, and didn’t even mention anything about it! 😂
@gotacopy821
9 жыл бұрын
How to I test drain pump.on this video.? kzitem.info/news/bejne/uJ95y6V8Zp-AqHY
@Appliancevideo
9 жыл бұрын
John Peck Please help us provide more videos to our site by subscribing to our KZitem page or posting ourwww.appliancevideo.com/ website on your Facebook or Twitter account. Our factory authorized technician’s also daily provide free professional Repair Help to people like you to help solve their appliance problems. You also have the option to email a factory service technician with a question at www.appliancevideo.com/repair-help/ . If you need of parts for your major appliance, we have over 5-million parts in stock at savemoreonparts.com/ . Thanks in advance for supporting us. So email us if you have any other questions our videos cannot resolve. Thanks for your support in advance. Matt, Ace Appliance service technician.
Пікірлер: 81