I"m a old lady and did as you said about unplugging and push cycle button it worked. Have a Blessed day.
@franciscosunworld
10 жыл бұрын
What is the point of showing that if you don't show how to fix it?
@roxy310ful
8 жыл бұрын
Do you know what causes it to blink and beep over and over
@supadigga
10 жыл бұрын
I held the "End of Cycle Signal" button for a couple of seconds and it fixed the problem. Now everything is back to normal. Hope this works for everyone else too. I think this all began from me leaning against the machine to push it back some and I might've pressed the buttons while doing so.
@mjbromack0917
9 жыл бұрын
You are the man it worked me also.
@chrisdarden206
9 жыл бұрын
H
@glenomary
9 жыл бұрын
C_Double_4 This worked for me as well. Thank you very much.
@kristenshepherd3291
9 жыл бұрын
You are a life saver it totally worked! Thanks!!!!
@supadigga
9 жыл бұрын
+Pamela Andres I'm glad it worked for you too! That service guy was a total rip off! Smh
@carynadzak8100
4 жыл бұрын
pressed end of cycle button for a few seconds and it worked!!!!! thanks
@ScreenPrintR
8 жыл бұрын
Thank you. Removed the bottom panel. Reached in and pulled the door tab. The door opened right up.
@washinton2008
10 жыл бұрын
Thanks man I have checked the manual I was about to spend 175 just in the control unit it self save me a bunch of hussle it worked for me
@candicabaniss2560
10 жыл бұрын
Thanks. I have a newer one, but the problem was the same. I did not look forward to calling my husband to work on this. I did not realize it was a button, but once I read this and realized I had been leaning on the machine it made sense.
@jamesmiara6248
8 жыл бұрын
Hold in the "end of cycle" button until "Controls Lock" light goes off. Simple as pie. To put the Controls Lock on, press the end of cycle button until it comes on.
@stanleyjones2085
8 жыл бұрын
it didn't work
@memokills1
8 жыл бұрын
it worked for me thanks
@Fopeneitor
8 жыл бұрын
I hav the same problem, how i can fix that míster jones???
@barbcage603
7 жыл бұрын
THANK YOU! Worked for us too! (Though we had both tried holding that button down before, maybe just not long enough.)
@nukhfiyanto2246
6 жыл бұрын
thanks.its work
@starburst5470
13 жыл бұрын
Thank you for this video, you helped me alot!!! I had been reaching behind the dryer to pick up something that fell behind it and thought I triggered a switch on the back...looked up troubleshoot, your video came up and what a relief to know how easy it was to fix. Thanks again! :)
@vibartmartins6052
11 жыл бұрын
Thank you. Had this problem for two weeks and finally decided to check here. Thanks again. My wife will think I am a genius.
@phillupweber
11 жыл бұрын
Dang!. My control panel was dead and I was ready to buy a new one. Saw this, went down and smacked righ front of panel a few times, hit control on button and she lit up and is all better! Thank you!
@MrNugga123
9 жыл бұрын
i UN plugged mine... UN did the water lines, pulled the drain line , rolled it out back, then ran it over with my bulldozer, until it was nice and flat. then sat it out by the curb, problem was solved immediately .. i then called brands mart and ordered a new one, had it delivered, re installed the new water lines and drain hose .installed new electric line ,it works just fine now .. and has a 2 year warranty. now my cloths are clean once again ...
@sintapride
9 жыл бұрын
I as well have a duet whirlpool dryer I've pressed END CYCLE BUTTON for more than 3 minutes and it still doesn't UNLOCK any other way PLEASE HELP
@roxy310ful
8 жыл бұрын
did you figure out problem
@sintapride
8 жыл бұрын
Yes thank you
@saraht28r
6 жыл бұрын
Tammy Shanafelt Hi, what was your solution? I am having the same issue :( thanks!
@saraht28r
6 жыл бұрын
Oops wrong person sorry !
@saraht28r
6 жыл бұрын
Sock Sowachowski Hi, did you find a solution? I am having the same issue :( thanks!
@626Opal
11 жыл бұрын
Mine is doing the same thing. We unplugged it many times...even had it unplugged for a week. It did turn on a couple times but stopped a minute in. Even held down the start button a long time. Looking on KZitem to see if we can fix it ourselves. Let me know if you find something.
@ricktheisen3108
9 жыл бұрын
I tried to start the dryer after someone used it. I couldn't get any of the buttons to work. Then I saw the control lock button. I thought maybe this button had been engaged and then never disengaged, so I pressed it again. Now it works. I wonder if it works as a toggle switch; that is, pushing it once engages it, and pushing it a second time disengages it.
@bernierodgers9409
9 жыл бұрын
this is exactly what is happening to mine... I have to unplug it for a few days and then hope it will work when I plug it back in. I push the control lock button each time, sometimes it works, most times now it doesn't. it has gotten worse now.. if I leave it plugged in after I get it working, when it is on standby for a period of time it will automatically start the beeping and then not work for weeks. what can I do to fix the problem? please help.
@appliancealliance4444
6 жыл бұрын
You can try pressing and holding the "end of cycle signal" button for 3 seconds or you can visit whirlpool's website at www.whirlpool.com or call 1-800-253-1301
@appliancealliance4444
5 жыл бұрын
What year and retailer did you buy this? Whirlpool discontinued these in the end of 2006.
@sabrinamcewen1981
9 жыл бұрын
Nothing is working, not even the. end cycle button. The control lock light is beeping non stop and is unresponsive to holding any button. I thought if I unplugged it for a while, it would reset. Still no good :(
@roxy310ful
8 жыл бұрын
did you figure this out mine is doing the same exact thing
@eddiefarrington6029
8 жыл бұрын
OK I have a whirlpool duet HT my lock/ unlock button is lit up and is locked how do I get it unlocked to wash my clothes
@TimothyFerris1687
9 жыл бұрын
Rebooting worked here. If the AC cord is hard to reach, consider cutting power at the 'fuse box.'
@JavonneNesmith-xy9lk
3 ай бұрын
What if nothing happens after holding it for 3 seconds
@celesteomealy5080
10 жыл бұрын
Thank you. At first I didnt' know what was going on and then I just did what you did. I pressed a few buttons twice each and it turned on :) I was losing it!
@washinton2008
10 жыл бұрын
Apparently the troubleshoot is the console unit where all the bottoms are mine did not meet the manual specifications but worked and I know for sure that will take care of the problem
@globalfaith1
12 жыл бұрын
Just did it and it worked. Thanks for posting this video.
@strokeofirish1
14 жыл бұрын
hold down the cycle control button for 3 seconds , it worked for me
@alfredoalvarezOR
8 жыл бұрын
removed AC power (with breaker box), then pressed the end cycle button (all the way to the right on my machine) for 5 seconds and we are back in business
@optimuz08
11 жыл бұрын
Mine keeps the locked control light on without beeps, what is the problem? Thxs
@sunset6610
8 жыл бұрын
Thank you. The end cycle button worked.
@marimar7270
9 жыл бұрын
I unplugged the machine for 10min. and then plugged it back on and held the" end of cycle button" at the far right bottom for a few seconds and it went back to normal.
@JusticeGirl
6 жыл бұрын
Your two-year-old dryer is FILTHY! No wonder is doesn't work properly.
@Boggie100s
11 жыл бұрын
"End of Cycle Signal" button for 3 secs worked for me! I wonder what causes this problem...
@ALeotta70
11 жыл бұрын
Accidentally hitting the 'End of Cycle' for 3 locks it. Doing it again unlocks it. There's even a small explanation of this under the 'End of Cycle' button
@djohnston1977
11 жыл бұрын
thank you ... I pushed end of cycle and its working.. thank you!!!!
@rickfrazier5284
11 жыл бұрын
I hit the right control panel out of frustration and mine went away which leads me to believe its a panel connection it may be related to how much vibration the dryer gives when in use
@treyl9636
5 жыл бұрын
I slapped the shit out of my dryer after reading your comment and it started working again so thanks!
@MrNguyen9999
12 жыл бұрын
@strokeofirish1 It happened the same to my duet whirpool washer and I tried it and it worked. thanks for your video.
@geosfullerjr666
8 жыл бұрын
I wasted 1:43 minutes of my time
@buellwinkle69
11 жыл бұрын
Press and hold the end of cycle signal button for more than three seconds.. the machine will beep and your problem will be fixed...
@heart4ace
14 жыл бұрын
IT WAS A GREAT HELP THANK YOU SO MUCH
@eddiefarrington6029
8 жыл бұрын
and I don't see control lock anywhere
@Dhtibab
7 жыл бұрын
Thank you, you son of a birch
@sofiagarzavargas518
10 жыл бұрын
Thank you!!! You saved my day!
@caseyswanson951
11 жыл бұрын
THANK YOU SO MUCH!!! TALK ABOUT HOW TO MAKE SOMEONE CRAZY!
@fisherjbf
12 жыл бұрын
Thanks Strokeofirish1! It worked!
@iamjames2
14 жыл бұрын
@strokeofirish1 like I said, holding down the button did nothing
@macarenamartinez8318
2 жыл бұрын
THANK YOU!!!
@kenwilliams5361
11 жыл бұрын
Pushed end of cycle button for 3 seconds and it was back to normal. Thanks You tube?
@jorgea.arellanes7514
10 жыл бұрын
Thanks I just unlocked mine...
@pegasus510sr2
7 жыл бұрын
this helped !! thank you
@jands0903
12 жыл бұрын
just imagine what his house looks like... gross
@luciaharo6083
9 жыл бұрын
THANK YOU........ Jeremy Page (Sloth) It work with mine model WGD94HEAW2.......
@DjassoTijbc
9 ай бұрын
Gracias
@youmnanaboulsi3607
11 жыл бұрын
thank you thank you thank you
@ayoprophet2646
9 жыл бұрын
Thank you!
@notmyrichieee
12 жыл бұрын
thank u ever so much! ;)
@eddiefarrington6029
8 жыл бұрын
I mean end cycle
@ronaldpatricia2
9 жыл бұрын
Thanks a lot also
@sennybe94
7 жыл бұрын
thanks a lot
@lucynation7961
9 жыл бұрын
Thank u so much ♡♡
@alomarbda1
12 жыл бұрын
thanks!
@andresitocasanova
7 жыл бұрын
presione end Of cycle signal varias veces o tenerle sostenido
@tinabraccioforte8894
3 жыл бұрын
That was a waste of my life
@kamizubi
5 жыл бұрын
What in the world was that???? Total waste of time
Пікірлер: 96