THIS MAN IS FANTASTIC. MAKES COMPLICATED THINGS REALLY EASY. mY 12 YRS OLD HOTPOINT WASHER DRYER IS WORKING AGAIN, FOR JUST 30€. PLEASE DON´T STOP DOING VIDEOS!!! AND THANKYOU
@eSpares
7 жыл бұрын
Thanks for the comments, remember to 'like’ the video if you enjoyed it or it helped.👍
@raegynking5153
7 жыл бұрын
thanks! I just saved myself 500 bucks by watching your video and fixing my washer myself!!
@eSpares
7 жыл бұрын
That is great to hear Reagyn. May we recommend another couple of videos you may find useful?: kzitem.info/news/bejne/ypyNsW2an2Oimpw and kzitem.info/news/bejne/1oF432Fvh3d3aHY
@BracliCreations
7 жыл бұрын
On our Duet, the F11 error was due to an intermittent 3 pin connector to the MCU. I re-positioned pins and sprayed off the terminals with Deoxit. Now it runs like new. Thank you very much for creating this video with emphasis on the harness connectors, you probably saved us $250 in repairs!
@eSpares
7 жыл бұрын
Thanks Keith for the comments, glad we helped.
@weAreNotAloneHere
9 ай бұрын
But there’s no mention of F11 on his video ? I don’t get it
@aura2407
6 жыл бұрын
I just fixed my washing machine thanks to you! It was the second error showed in this video :)))) Thanks a million for this video!
@eSpares
6 жыл бұрын
Thanks for the comments Aura, remember to 'like’ the video if you enjoyed it or it helped.👍
@hulksmash3854
8 жыл бұрын
thanks for the help man!! but we had to change the entire mother board which cost 3500/- now it's working fine!!!
@eSpares
8 жыл бұрын
Glad you resolved the problem. :-)
@gramos9115
Ай бұрын
Brilliant , this guy should be on TV ! I waited for an error code E33 but this is from a de longhi w/m , can you tell me what that would be ?
@noanyobiseniss7462
3 сағат бұрын
f01, replaced pump and it starts to pump but then stops and errors with brand new pump.
@Colocsty
6 жыл бұрын
thanks for the video, I was able to fix my washing machine !!!
@eSpares
6 жыл бұрын
Hi Colocsty! We're glad to hear this video helped you fix your appliance. We hope it’s all sorted now.
@danski723
3 ай бұрын
Thanks! 🙏 ( You didn't talk about F23 code...)
@markthomasmendoza4162
10 ай бұрын
Great video... I have a question... What seems to be the problem with my Whirpool dryer... Showi g error code F19?
@integrafreak1
7 жыл бұрын
Thanks for the quality video.Very helpful, Thanks a bunch!!!
@eSpares
7 жыл бұрын
Tanks for the comments. 😊
@jawadamkassou8235
8 ай бұрын
Hello, what does the F13 code indicate, even though a new lock was replaced and the number is still the same and the machine does not work, the door locks and does not work and the service light is on?
@miklosbenkoczy3819
8 жыл бұрын
Very good anyway through your own videos!
@sujithps6429
8 жыл бұрын
Ur video full send me
@4bangerftw
7 жыл бұрын
Thank you! Helped me solve my issue!
@eSpares
7 жыл бұрын
You are welcome Marc-André, don't know if you have seen this?: kzitem.info/news/bejne/tHyOsIl4sZ9pn34
@DEE-jz7cy
2 ай бұрын
What about FA error code. We have a dreamspace whirlpool front loader
@bbq2001it
7 жыл бұрын
Thank you so much, I will follow your advice
@eSpares
7 жыл бұрын
😊
@evelynstice6751
10 ай бұрын
What does F1 mean? I know it has something to do with the lock cause mine is locked, and I can't get it open. It's not the control lock. And I have had it unplugged for at least 5 minutes.
@ForrestLtd-yv2je
10 ай бұрын
Hi. I have an error code F23. Any idea what that relates to? Thank you 🙏
@user-pm3iy1qz1b
5 жыл бұрын
شكرا على الشرح ، عندي سؤال: أعمل في مجال الصيانه الالكترونيه للغساله ولدي غساله تعمل بشكل جيد وعند الدوره السريعه تقف عن العمل وتكتب F8
@eSpares
5 жыл бұрын
مرحبا, يشير رمز الخطأ الخاص بك إلى وجود مشكلة في السخان قد تكون دائرة مفتوحة ، استخدم مقياس متعدد لاختباره للتأكد مما إذا كان قد فشل.
@furiousjumperfan7622
6 жыл бұрын
Thanks you vidéo wirpool error [ HELP HOTPOINT ARISTON ERROR F05
@hanyman2009
5 жыл бұрын
Thank you , you save my life
@eSpares
5 жыл бұрын
Hi hany Man, great praise indeed we are glad we could help.
@ForrestLtd-yv2je
10 ай бұрын
Great video by the way
@letsdoithandymanletsdoitha9747
5 жыл бұрын
Thanks for excellent video... please one question, is same error codes for all whirlpool? Thanks
@eSpares
5 жыл бұрын
Hi Let's Do It Handyman Let's Do It Handyman, newer machines may have different error codes but generally, they have stayed the same.
@juliang.7963
8 жыл бұрын
This is a good video thank you guys 👍👍👍
@eSpares
8 жыл бұрын
Thanks Julian, if you have a problem remember we also have loads of 'diagnosis videos' for all most appliances like this: kzitem.info/door/PLZopaZU-UQSHj1noiwEJ99JjXWcEcSAbZ
@hughesgaragedoorsystems5893
7 жыл бұрын
Well. I checked the connections of the water supply and cleaned them out. Then checked the dispenser compartment for clogs.Massaged the hose just in case a blockage was there. None. I didn't check the solenoids because I don't have a meter. Pressure is ok but still getting 3 beeps. The major is filling up to proper level of water. Water pressure sounds good. I cut down the hose on the back so water would drain properly. Still no good results....HAve anymore Ideals?
@eSpares
7 жыл бұрын
The information you have given suggests you may have a pressure switch problem. For information on this see another video: kzitem.info/news/bejne/k6Z_vJ93sYmEi5w
@denisestearn5563
6 жыл бұрын
My son just moved into a beauriful town home on the water but so many things are not working properly such as his whiirl pool side by side washer and dryer. The washer works horrible. Everytime he attempts to wash a load of clothes an area code A-09 comes on. He cant open the door and the only way hes able to is if he puts it on the rinse and spin cycle. Which is time consuming and not only that the electic and water bill is going to kill him. Thats one of the issues here that the electric bill is so high tenants have actually moved out.
@eSpares
6 жыл бұрын
Hi Denise, error code A09 is the machine saying there is a water inlet problem, your son needs to check the water supply and make sure there is water getting to the machine.
@AyushKumar-oh8pv
7 жыл бұрын
thank you for your help
@eSpares
7 жыл бұрын
:-)
@pearteddwards4172
5 жыл бұрын
How to fix a f3 problem
@emilfranciscastro1717
9 ай бұрын
If the error code is Ed2?
@SolangeWaithe
6 жыл бұрын
Thank you so much
@pcno2832
7 жыл бұрын
I'm getting an E01/F03 on a new USA-made Whirlpool, which isn't listed here. I notice that many of the unanswered questions below pertain to US-made Whirlpool products. Is it possible that the error codes on EU or UK sold WP machines are different from those of their US counterparts? I know WP bought out Indeset/Hotpoint, so the design of the machine here may have little in common with mine. Thanks for the information anyway.
@eSpares
7 жыл бұрын
There can be different codes even for machines made for the same 'markets' but the codes quoted are the 'commonly used'. E01 can be a draining problem and F03 can be a pressure switch related error so if you are getting these it suggests the machine is 'expecting' the water to be completely drained but the pressure switch is 'reporting' water in the drum. The usual cause would be a partial or complete drain blockage so watch another video for more information: kzitem.info/news/bejne/x6h7sJyOcoWho6w
@user-qq7jl6xx9p
4 ай бұрын
How about E d1 , ??
@ashokdobariya6567
6 жыл бұрын
Thank you sir
@cdfarah
4 жыл бұрын
Hello, I have a whirlpool sports 6th sense. It's washing fine but lately I have noticed that loads are going on for far too long. For example there will be 1 minute left on the screen then it goes back to 30mins rinsing over and over again. Eventually I will manually reset and do a rinse cycle to finish off. Please help!
@eSpares
4 жыл бұрын
Hi cdfarah, start by checking if it is draining the water correctly and this may interrupt the programme, also test the heater as that may be a issue.
@jacquimcalinden-wall8868
7 жыл бұрын
Hi, I have a Whirpool HDW 1011WG, halfway through the program the window flashes H then F, then H then F continously. Then select pause reset button and time comes up 21 mins and pump runs continous and won't move on from there
@eSpares
7 жыл бұрын
The FH error is indicating the machine has a problem with filling. Check the water supply is correct .
@katefleming2287
7 жыл бұрын
I have a Duet steam model wfw8640bw1 about 3 years old. The power button no longer works and when I try to start a load the delayed start is displayed after holding start buttons for at least 30 seconds. I have to try several times for the cycle to begin. Suggestions?
@eSpares
7 жыл бұрын
Hi Kate, you need to watch another video to help identify the problem: kzitem.info/news/bejne/so-G16SghYhopmk
@s11039858
6 жыл бұрын
What does error 551 or SS1 indicate? Please advise
@eSpares
6 жыл бұрын
Hi Ashneel, we do not have either error codes listed on a whirlpool washing machine, you will need to contact the manufacturer but please let us know how you get on.
@ShabbirAhmad-xp1km
5 жыл бұрын
Hello my whirlpool washing machine Giving F 26 Error how i solve?
@ViZor_edits
5 ай бұрын
How to solve error code e6c ???
@themimis435
5 жыл бұрын
Great video. I had f01 issue which got fixed by replacing the control panel, and it worked for 1 day and then start showing me error f31. any guidance?
@eSpares
5 жыл бұрын
Hi The Mimi' s, F31 means the machine has detected the motor control unit has overheated, check the connections from the motor to the central control unit and test the motor to determine if it has failed.
@themimis435
5 жыл бұрын
@@eSpares I did and they are fine. now it is showing me new error f-28. Did I burn the motor?
@eSpares
5 жыл бұрын
Hi The Mimi' s, F28 is a communication error between the boards, try this Unplug washer or disconnect power. Check wiring harness connections to the MCU, the motor, and Central Control Unit (CCU). - Check connections of the CCU board within the housing. - Make sure all grounding switches are engaged. Check that the serial harness at the MCU is not mounted upside down. The wires should be to the left when facing the MCU connectors. Check the drive system for any worn or failed components the plug in the washer or reconnect power.
@micheljubran3427
4 жыл бұрын
hi, thanks for your awesome video! I have a WFW9050XW03 but it doesn't have a LED display, how can I decipher the error code ?. it is stuck on Wash, beeping 3 times, and the LED on the WASH flashing 8 times and then once and then repeat. thanks a lot!
@eSpares
4 жыл бұрын
Hi Michel, the code is generated because the fill sequence is taking too long, check the pressure switch hose that runs from the tub to the pressure switch as this can cause the problem.
@micheljubran3427
4 жыл бұрын
@@eSpares Thank you very very much! will give it a shot and update ! really appreciate the quick response and help! you totally rock!
@pankajkhurana5772
6 жыл бұрын
Hi, I have a ifb front loading washer, its showing an error code AC HI. Please help, Thank you very much.
@theaaleol2868
4 жыл бұрын
I have a front loader washer whirlpool energy saver. When I press the start button, door locks but then that’s it. No water and no spinning. Timer works but machine is stuck
@eSpares
4 жыл бұрын
Hi Thea Ale Ol, check the inlet valve with a multimeter which will determine if it has failed.
@JM-ml9xw
5 жыл бұрын
Hi I have a whirlpool duet front load washer the code disappeared however the red door locked but is lit up. And it sounds like it’s draining but not unlocking even after minutes please help what should I do?
@eSpares
5 жыл бұрын
Hi J M, let's start by getting the door open this video kzitem.info/news/bejne/q22s4It9hqiXgoI&t shows you how to release the door then check the door lock and the electrical connections between the lock and the board.
@AyushKumar-oh8pv
7 жыл бұрын
my washing machine shows de error and sometimes Fe error please help
@eSpares
7 жыл бұрын
Hi Ayush, you did not give a model so I can only give general advice. DE usually indicates a door error, check the door closes correctly and if it reoccurs suspect the door lock. Error FE is usually a filling error. Check the machine fills to the correct level in the right time (about 1 Minute), check the water supply tap is turned fully on.
@RahanComhaltas
4 жыл бұрын
How about an answer for the E 11 code i have on my Whirlpool Washer/Dryer AWG 349/4
@eSpares
4 жыл бұрын
Hi autocuntversions, it means the machine has detected an error with the dryer sensor, we have an article to help on this www.espares.co.uk/advice/symptom/hoover-washer-dryer-error-code-e11
@rowenaflorendo2382
5 жыл бұрын
My wash mach always dispalys e1 during the process
@eSpares
5 жыл бұрын
Hi Roen, error E01 refers to a drain issue, check the filter and pump.
@eleonoravitanova8127
4 ай бұрын
F 26 ? What can i do ?
@lisarenfro1188
7 жыл бұрын
Ok, I've watched this video twice now because the first time I didn't hear my problem.......or the second time. I have a Whirlpool Duet washer and am getting a F13 error. Please advise.
@eSpares
7 жыл бұрын
Hi Lisa, although we have tried to make this a comprehensive list manufacturers will occasionally add another code. We believe this code is related to a motorised dispenser. The detergent dispenser has several compartments to allow pre-wash wash and conditioner to be loaded at the correct time. To do this it will 'divert' the filling water to the correct compartment. If the motor is jammed or if the control board is not receiving the feedback it will show this error. Check nothing is jamming the motor or flap.
@jponyboyace
6 жыл бұрын
Whirlpool duet f21 code could be a problem other then drainage?..
@eSpares
6 жыл бұрын
Hi, we recommend checking the drain hose for kinks, check the condition of the drain pump and the electrical connections and check for any blockages inside the drain pump filter,.
@schakal325
6 жыл бұрын
Hello there eSpares! I too get an F23 faulty code on my top load Whirpool AWE 7516. What should i check? The pressure switch,the heater or the heater sensor? Thank you !
@eSpares
6 жыл бұрын
We believe this could be due to a couple of reasons. If the error occurs when filling with water it may be a blocked or failed pressure switch so see this video: kzitem.info/news/bejne/k6Z_vJ93sYmEi5w
@schakal325
6 жыл бұрын
eSpares my problem is that i fill the washer with clothes, pick the program and start it. When i start it, there is NO water coming in, the motor goes twice for a couple of seconds and puff.. the f23 comes on.
@eSpares
6 жыл бұрын
Hi schakal325, first test the element because if that has failed it may cause the water valve to stop, if that is ok then suspect the pressure switch.
@schakal325
6 жыл бұрын
eSpares what element? You mean the heater element?
@eSpares
6 жыл бұрын
Hi schakal325 sorry yes the heating element
@pauledan9934
8 жыл бұрын
checked the heater and senser,working normal Is there any issue in main control board (model no. AWO/D 8712) Whirlpool
@eSpares
8 жыл бұрын
All modules and PCB's can fail. Before suspecting this just confirm the machine is filling and starting a wash cycle?. Also try a spin cycle. If F08 appears immediately before the cycle starts suspect the sensor or the board.
@kathyhaggard6287
5 жыл бұрын
My Whirlpool front loading machine, Model GHW9150PW4, starts to wash as usual but clicks off after a few seconds and locks the door, with Error Code F11. The manual and you did not mention Error Code F11. What is going on with my machine?
@eSpares
5 жыл бұрын
Hi Kathy, F11 is a communication error between the control board and the motor board, try checking the connections to both boards are making direct contact.
@kathyhaggard6287
4 жыл бұрын
Thank you for your quick response. I will have my husband do what you suggested.
@emmanueltorrente3128
7 жыл бұрын
I have bought a washing machine it is 50hz, will it runs properly to 60hz power supply? please help me solve my problem...
@eSpares
7 жыл бұрын
Hi Emmanuel, This will depend on the machine and as you have not given a model number I will try and give information that may help. Generally if the machine can work it will show the following (50/60hz) on the 'rating plate' where the model, serial number and voltage information is listed. If the machine uses a 'mains voltage pump' it is likely to be upset by supplying the wrong mains supply.
@ravenj4068
5 жыл бұрын
I wish my machine showed a code. All the lights just light up and it just beeps nonstop. Any thoughts?
@goma5699
3 ай бұрын
What about H?
@beatrizchenzhou9603
4 жыл бұрын
Error F18. The drum doesn’t spin. What can I do?🙏🙏🙏
@eSpares
4 жыл бұрын
Hi Beatriz Chen Zhou, it is in the video F18 means the machine has detected an internal data error, try unplugging the machine for at least 3 minutes, reconnect and wait 30 seconds before trying again but if it happens again suspect the PCB.
@RCS-ONE
5 жыл бұрын
How did you remove the front ? The rubber won't come loose from the front panel
@eSpares
5 жыл бұрын
Hi Richard, use a flat blade screwdriver to lift the retaining band off the door seal then you can pull the seal away from the cabinet, there should be screws at the bottom of the panel holding it on and just lift it up to release and take off.
@RCS-ONE
5 жыл бұрын
@@eSpares the rubber is stuck on the fron panel. That comes loose. There's a screw on the machine part but I'm afraid that when i take that of i never going to put it back anymore. The rubber is to tight.
@eSpares
5 жыл бұрын
Hi Richard, if this is the first time the seal has come off the front panel they can be very tight to remove but they are designed to come off, try putting your fingers on the inside of the seal where it joins the front panel and push down and it should move the seal watch this video to help with the technique kzitem.info/news/bejne/r6Ga3X2NgKSAi6Q&t
@shinedeva9553
5 жыл бұрын
Whirlpool white magic 6th sense...the wash light s showing a warning..red colour with a beep sound..what to do..
@golo5000
7 жыл бұрын
Can you tell me what a F08 and E01 error means and how to solve it. TIA.
@eSpares
7 жыл бұрын
This is a 'water supply error' where the machine does not think it has filled enough in the allowed time. For more information see our video: kzitem.info/news/bejne/t4lqnnuVnKl0i6Q
@asiasmith5511
7 жыл бұрын
Hi I'm getting a code Lf. I've had someone come to check it bit that didn't do Me any good just lost money. I would rather learn how to fix it myself. ..
@eSpares
7 жыл бұрын
The code LF means long fill so check the water is filling the machine correctly and the water supply is fully on.
@asiasmith5511
7 жыл бұрын
eSpares how would I know if the water is filling correctly? These machines don't really put out much water, so I really don't know what would be a good amount. I had someone come out, but that was just a waste he's telling me other things that's the opposite of my problem. .. is this something I can fix on my own or would I have to purchase another washer. my machine starts a whole new washing cycle on its own. Once a cycle is finished it comes up with the error code Lf and then it'll rewash the same load if I don't power it off in time. I'm very concerned especially concerned about what my water bill will be like next month.😓
@denniemcbrayer2740
6 жыл бұрын
What part did you say f06 was? Thank you.
@eSpares
6 жыл бұрын
Hi Dennie, F06 on a whirlpool washing machine refers to a door lock fault.
@promochamaker
6 жыл бұрын
I dont get any power in whirlpool awo/d 4731 what to do???
@samuelboone1603
4 жыл бұрын
What does f33 mean
@eSpares
4 жыл бұрын
Hi Samuel, error code F33 means the machine has detected an issue with the drain pump circuit, check the filter and test the drain pump with a multimeter.
@shamayabryant2963
5 жыл бұрын
I have a whirlpool cabrio washer and when it first cuts on the the water runs for about 5 seconds or sometimes longer then it beeps and stops the displays “du”
@eSpares
5 жыл бұрын
Hi Shamaya, we believe the error code may be related to the lid locking mechanism as the module board cannot determine if the door lock is locked or unlocked.
@arjeanvillodres7420
5 жыл бұрын
Whirlpool 6th sense has U4 error code, what does it mean?
@eSpares
5 жыл бұрын
Hi arjean, we don't have U4 listed so hopefully somebody has come across it and can put i on here.
@suziemarie5617
9 ай бұрын
What about F70?????
@ardysuareztv
8 жыл бұрын
I've done everything in the video f21 error is still there . Resetting this model mhn30prbwwo commercial type without coin or card dispenser ,is very hard to find out . I did what you said to unplug the washer for 2 minutes and put it back again .i made several times . No reset is happening washer is not running . What should i check next Ccu or mcu ? Is there any handheld device to reset this .thank you !
@eSpares
8 жыл бұрын
Sorry we do not have information on commercial machines. The only suggestion we can offer is to watch one of our diagnosis videos that will give areas to check to help identify where the problem may be: kzitem.info/news/bejne/so-G16SghYhopmk
@zorbasmiling5981
6 жыл бұрын
Whirlpool professional 7.0kg Giving HE1 Error code . Machine Stop Within 4minute when we start the machine.
@eSpares
6 жыл бұрын
Hi Zorba, the only thing we could find on the HE error codes for whirlpool relate to problems with the drain cycle, check the drain hose and filter before suspecting anything else.
@AttilaAntal
6 жыл бұрын
Hi, I have a Whirlpool Supreme Care FSCR70414 and when power on it displays a code "dEn" (that "n" is like an "U" upside down, so maybe "dE17"). The only option that I have is to touch the start (play) button but in this case I have a random program shown and It happens nothing. At this moment the only functionality is the power of, for any other it just beeps. Do you have a hint what is happening?
@eSpares
6 жыл бұрын
Check the door lock first, if this seems OK watch this video: kzitem.info/news/bejne/so-G16SghYhopmk
@giuliopoli69
7 жыл бұрын
Please!! I wish I could disassemble the electronic principal board on my whirlpool awo-d6126.. Where is it exactly located?
@ayoubyacine731
5 жыл бұрын
ال
@bommaritohawaii
6 жыл бұрын
When you say F9 error code check for leaks inside the machine I'm not sure how you would do that? I'm getting the F9 E1 error code and the system is not draining. I took it apart and there are no clogs or plugs at all
@t3m0tj93
5 жыл бұрын
How do you fix it?
@KL-ie4xm
5 ай бұрын
Thx
@pablos5332
6 жыл бұрын
I get F33 error code on my Kenmore Elite HE4t, what could be de cause?
@eSpares
6 жыл бұрын
Hi Pablo, error code F33can suggest to multiple issues related to it, check the water supply first then the pressure switch for holes in the hose and the flow meter is functioning. test the pump with a multimeter and if all that is ok then it is likely to be control unit, good luck.
@Cv5527
7 жыл бұрын
I have a new washer with codes E01 and F03, what are these?
@eSpares
7 жыл бұрын
F3E1 error can be a blocked pressure switch hose stopping the machine identifying the water level in the drum. For more information see our video: kzitem.info/news/bejne/k6Z_vJ93sYmEi5w
@beczijohanna569
6 жыл бұрын
Chris Velez dtdfcdyrgdfdfffdggfgfvgh
@maria.doloresmendoza363
6 жыл бұрын
Chris Velez
@maria.doloresmendoza363
6 жыл бұрын
Tengo un código F 28 wilpoo .duet th por favor si puedes darme respuesta cuando es el problema gracias por anticipado una vez gracia.
@furiousjumperfan7622
6 жыл бұрын
Chris Velez help it's Hotpoint Ariston no spin HELP !!!
@hydro2668
5 жыл бұрын
What do I do if I get two codes. The codes are F05 and E02. Don't want to spend a lot of money for no reason
@eSpares
5 жыл бұрын
Hi Eclipse Hydro, on some models whirlpool use 2 error codes which reads F5 E2 which refers to the machine has detected an error with the door not locking correctly so check the door is closing properly, make sure the connections to the lock are OK before suspecting the door lock.
@hydro2668
5 жыл бұрын
@@eSpares thank you so much
@jack310111
7 жыл бұрын
Hi how do I access the pump on my Whirlpool duet front loader with a solid front and no access panel. Thank you in advance.
@eSpares
7 жыл бұрын
Hi Chris, without a model number we can only give general advice. It is usually easier to lower the machine on its side and access from beneath as shown in some of our other drain pump videos.
@drakausdromgatti58
4 жыл бұрын
What about F28?
@hughesgaragedoorsystems5893
7 жыл бұрын
This is an american model and has no display. How can I put it into service mode to check codes?
@eSpares
7 жыл бұрын
Sorry we do not have information on this.
@hughesgaragedoorsystems5893
7 жыл бұрын
I have a whirlpool Dual Tumble Fresh 4.0 and normal load goes through to last rinse cycle then shuts down and three beeps continuosly. Put it on Rinse Spin Cycle and the beeps came up during a fill cycle. Machine is level front sensor at kick/front panel is pressed. Don't know what to do from here. Please help.
@eSpares
7 жыл бұрын
This sounds like a filling or pressure switch problem, check the water flow is fast enough (turn tap fully on) and see the following videos: kzitem.info/news/bejne/t4lqnnuVnKl0i6Q and kzitem.info/news/bejne/k6Z_vJ93sYmEi5w
@koreyprest3821
7 жыл бұрын
J.C. Hugh
@biologybyarpita
6 жыл бұрын
my whirlpool automatic washing machine 6.5kg is showing E1 and water is flowing continously
@eSpares
6 жыл бұрын
Hi Arpita, according to the whirlpool website E1 refers to no water has been detected so check the water valve before suspecting anything else.
@loreatherton1474
7 жыл бұрын
am getting a flashing f27 on my AWOE 9140
@eSpares
7 жыл бұрын
We understand this is an overflow error indicating the water has filled too high in the drum. Reset the machine and watch a cycle to confirm the water is filling to the correct level.
@bukkyakala9257
6 жыл бұрын
I'm getting f9 E2 what problem is that?
@eSpares
6 жыл бұрын
Hi Bukky, F9 is described in the video at 3.43 which refers to a leak has been detected so check for a leak.
@CAZNTUBE
6 жыл бұрын
Hm good guide but what about a non signal machine...desk stays black ?
@eSpares
6 жыл бұрын
Hi CAZNTUBE, if your display is blank you need to check you have power so unplug the machine and plug something else in the socket to see if it works, test the fuse and use a multimeter to check from the plug to the board.
@CAZNTUBE
6 жыл бұрын
tnx, I had contact with a repair-store and they told me its the input electric board or something that's out of order' costs derectly 150 a 200'euro need to repair this...
@jitinkochhar9956
6 жыл бұрын
If there is no display screen on the machine? Hi .. I have Kenmore He2 with no display screen to check the error code. What it does is ... When I start the machine nothing happens and it unlocks and then it locks back in after few seconds .. Then the water fills into the drum to an appropriate level and then the drum spins once and stops for a minute or 2 then all lights starts flashing after few minutes it drains the water and unlocks the door. I cleaned the drainage filter and also could hear a little squeeking noise when I rotate the drum by hand although the drum is rotating freely. My Machine vibrates like hell when on high spin. Kindly share your expertise.
@pembs1
8 жыл бұрын
The door seems to open and close fine. The end light is now permanently staying on and won't let me select a programme. Is there anyway of resetting the system please?
@eSpares
8 жыл бұрын
When the power is turned back on the system should reset. Check the motor brushes are not worn out and see our other videos: kzitem.info/news/bejne/pWt33Wt5e3d4g34 and kzitem.info/news/bejne/so-G16SghYhopmk
@dranoelwillas6829
6 жыл бұрын
Hello! I have an whirlpool washing machine AWE6317 and work only the motor! I habe doing the reset ine the first the machine takes the water when goes to the second the motor works very fast 2 times and the washing machine stops and 3 light are on! The service light and anothers 2 in program! What problem has?
@eSpares
6 жыл бұрын
Hi Leonard, we have not found any information and the error codes for your machine, we do not have top loader in the UK.
@navigatorsumit
6 жыл бұрын
What is tsc error in whitemagic 123 top load ??
@eSpares
6 жыл бұрын
Hi Navigatorsumit, we do not have a list for your model so contact the manufacturer for the details if the error code.
@arkudamon
6 жыл бұрын
So I tested the element and had no reading on the meter. So I decided to buy a new element and replaced it today ...the washer is heating up again and it works however I still get F08 as an error code even tho it heats up the water. Do you have any idea why? Please don't tell me it's the thermostat that will take another 4 days for delivery and it's more expensive then the bloody element 🤦🏻♂️
@eSpares
6 жыл бұрын
Hi Arkuda, the board is still recognizing the error code, try to unplug it and leave it to try to reset the electronics.
@arkudamon
6 жыл бұрын
eSpares but when I was changing the element it was unplugged? (Of course)
@eSpares
6 жыл бұрын
Hi Arkuda, try this we found 1. turn off the washing machine and unplug 2. press the start/pause button for at least 5 seconds 3. plug the washer back in and hopefully, it has reset, if not it could be a malfunction in the board.
@arkudamon
6 жыл бұрын
So I took it apart again checked for continuity and it all seemed perfect. Managed to get into service mode and then it said F13 🤦🏻♂️as if I don't have enough problems lol. However F08 was gone from the service mode ... Test was successful door did look and unlock without a problem tho ... So decided to do an empty 15 min cicle and what do I see at the end of it ... F08 flashing with the service light 🤦🏻♂️ I am so frustrated
@eSpares
6 жыл бұрын
Hi Arkuda, you have obviously tested the components correctly so we can rule out the element, it does suggest that the only thing left is the board.
@bizzobrigante1588
7 жыл бұрын
I have a F06 Error and it's not a motor brushes ( they are practically new! ). I've hear in your video @ 4:23 that there is a "Tacho Coil" that might be damaged? Should I check electric resistance of a coil? Thanks in advance.
@eSpares
7 жыл бұрын
F06 error is no feedback from the Tacho coil. When this normally occurs the drum would start spinning very fast as the motor is powered then slow and stop as no feedback was received. If the drum does not spin that is the reason why no feedback (F06) is displayed and that would be a drive problem.
@bizzobrigante1588
7 жыл бұрын
eSpares funny thing is that the motor won't start at all?! After taking water the machine just stalls and F06 error pops up. That's why I'm worried that it could be MCU or even CCU which is in my opinion not worth fixing.
@eSpares
7 жыл бұрын
As previously described no motor rotation no feedback so ignore the F06. If brushes are OK it must be either a connection or a faulty power board.
@bizzobrigante1588
7 жыл бұрын
eSpares I'll check connections first and then will see from there. .. thanks for help...
@gouthamvinu2645
5 жыл бұрын
HE2 Eror in whirlpool front load
@eSpares
5 жыл бұрын
Hi Goutham, whirlpool don't list error code HE2 can you please clarify the model details.
@cobix2057
8 жыл бұрын
Hello, I have a Whirlpool machine also and i got a F 05 error. What can i do ? To fix it or repair ?
@eSpares
8 жыл бұрын
Run a short cycle on a hot wash and check if the water is showing signs of heating. if it is suspect the temperature sensor if it is not check the heating element.
@mistyhensley9609
7 жыл бұрын
hi I'm getting an f7 e6 also f5 and e1 not sure about this one but it's an f0 and e0 please please help
@eSpares
7 жыл бұрын
We believe F7 E6 error is a motor drive problem and F5 E1 error suggests a lid switch problem so check there areas.
@ShabbirAhmad-xp1km
6 жыл бұрын
Siemens washing machine gives E 003 error what the problem plz tell
@eSpares
6 жыл бұрын
Hi Shabeer, we do not recognize the error code E0003, can you give us some more details of the fault and model and look at this video for help kzitem.info/news/bejne/sayA0qWFo3lniJg
@harkeshkumar4552
5 жыл бұрын
Hi i have whirlpool wasing machine its showing error 7 pls tell waht the isssu how to fix
@eSpares
5 жыл бұрын
Hi Harkesh, we talk about it in the video at 4.26 Mat says that F07 which is the same as your F7 relates to the motor so start there.
@joebillingsley6663
7 жыл бұрын
My washer dont have thedigatal display how do. Do i know whats wrong it just beeps three times
@eSpares
7 жыл бұрын
Many machines bleep three times to either indicate a problem or that the cycle has finished. If you do not have an error code check what works by following this video: kzitem.info/news/bejne/so-G16SghYhopmk this will help show what is going wrong.
@7venteenth
3 ай бұрын
Nothing say about F13????
@hone148
7 жыл бұрын
hi, I'm getting a 5d error code, I cleaned drain out an found some debris. ran the machine in quick cycle an still 5d error code at the end of cycle, I repeated 2 more times same result, I then proceded to run the clean cycle with bleach and still 5d error code at end of cycle. I have the model WFW-8410. in your opinion is it the Pump failing or maybe a sock clogged in hose behind pump??
@eSpares
7 жыл бұрын
Error SD is usually indicating suds or excess foaming in the drum. This is usually caused by to much detergent so if it occurs run another rinse cycle and try reducing the detergent. If you suspect a drain problem watch our diagnosis video: kzitem.info/news/bejne/x6h7sJyOcoWho6w
Hi, I have a whirlpool awz 512/s e and the start button just keeps flashing on it and then it goes onto start delay but it won't enter into any wash programmes. Any ideas what the error might be please?
@eSpares
8 жыл бұрын
Check the door switch is working correctly.
@luiszaserbu7453
3 ай бұрын
F22 ?
@alesiapeshku3777
7 жыл бұрын
Hello! i got a f12 error. could you please tell me how to fix it? thank youu so much in advance
@eSpares
7 жыл бұрын
Check the heater with a meter as it is likely to have failed.
@eSpares
7 жыл бұрын
F12 is usually a heater error so check the element. If this is ok the problem could be the control board.
Пікірлер: 483