One step at a time...stuff like this can get ya thinkin! How did the designers , ever...come up with this stuff..n did they eeeevvveeerrr think that some " DIY " mechanic, would be tearing into the guts of their creation?? Lol! Ya got this??!! 👍🔧🧙♂️🪛👍!
@heyyoubuddy6749
2 жыл бұрын
Good morning buddy how are ya? Looks like an sm420. Great old tranny super low gears! I will be doing the same thing to my bell housing behind my 225 v6. But will use a sm465 due to shorter over all length with a adapter. I can’t wait for the next video. Thank you so much for all you share. God bless you and you wonderful family.
@redeyecafegarage7484
2 жыл бұрын
Thank you! Yessir it’s a 420. I’m sure you’ll love the 465. That’s an awesome transmission! Thanks for watching! We really appreciate it!
@davedegan12
3 ай бұрын
Is there enough meet for the larger hole sm465? I see the sm465 adapter is less than an inch. Might be a better swap for the flat finder
@187manowar
2 жыл бұрын
Nice work again. Do you just do this as a hobby or were you/are you a machinist for a living?
@redeyecafegarage7484
2 жыл бұрын
I have a small machining and fabrication shop.
@cubanstyle6643
8 ай бұрын
Ohhh man I just got my 1946 , and I would to know if are available to the swap on my CJ-2 ?
@redeyecafegarage7484
8 ай бұрын
Anything is possible With enough time and money
@brandonfuchs3499
Жыл бұрын
Awesome content! I’m getting ready to swap an sm420 into my 3a with the L134 and was wondering if you had to alter the main shaft to accommodate the pilot bushing? Thanks!
@redeyecafegarage7484
Жыл бұрын
Thanks! I’m running a cj5 flywheel with the stock sm420 input shaft and a custom pilot bushing I made.
@brandonfuchs3499
Жыл бұрын
@@redeyecafegarage7484 Awesome, thanks for the info on this swap.
@jashann
2 жыл бұрын
Hey Seth, amazing work! I'm working on a sm420 swap myself. Which adapter are you using to mate to the D18? I know advance adapters has a kit but yours looks a bit different.
@redeyecafegarage7484
2 жыл бұрын
Thanks! Mine is a custom made piece based off of the advanced adapter kit.
@jashann
2 жыл бұрын
@@redeyecafegarage7484 good stuff man! Love all your videos/posts
@redeyecafegarage7484
2 жыл бұрын
Thank you!
@davedegan12
2 жыл бұрын
Great video. Are you still using the willys throw out bearing? I see you welded the clutch fork ball stud to the sm420.
@redeyecafegarage7484
2 жыл бұрын
Thanks! Yessir. The stock willys throwout bearing is used in this application. That makes it. Nice for booking up the stock clutch fork and cable.
@davedegan12
2 жыл бұрын
Which adapter did you use from the 420 to D18? Also some videos of the floor mods. Thanks!
@alanafbaker
3 ай бұрын
Did you use any of the original sm420 bell housing mounting holes? Looks like all 4 bell housing holes had to be drill and tapped in the trans case to fit the Willy’s bell housing
@redeyecafegarage7484
3 ай бұрын
This is a full custom conversion. Nothing lines up. lol. The Willys and GM do not share any holes.
@alanafbaker
3 ай бұрын
@@redeyecafegarage7484 Thank you for the reply! I’m sure I’ll have a lot more questions
@alanafbaker
2 ай бұрын
@@redeyecafegarage7484 could you provide more details on the flywheel and starter that you used for this setup?
@adhityamulyaandhika
2 жыл бұрын
I have a question, can I use an amc sedan gearbox or a toyota rwd sedan / pickup instead of a Willys gearbox? Thank you 🙂
@PedroCalderón-s5t
Жыл бұрын
This gear box Is sm465?
@redeyecafegarage7484
Жыл бұрын
sm420
@PedroCalderón-s5t
Жыл бұрын
@@redeyecafegarage7484I from Costa Rica. No speak inglesh.Can I change the t90 for sm465? swap sm465?
Пікірлер: 27