Does anyone have any specific struggles with rigging?
@franogracin2326
3 жыл бұрын
hopefully not aymore :)
@theylive1999
11 ай бұрын
First part, probably because it's an old sail (rigid) so I'm struggling to get the mast through, the battens get twisted around the mast. Any suggestions?
@willnicholls5
11 ай бұрын
@@theylive1999 With old sails it can be tricky. I try to make sure to line up the luff tube with the mast (as much as you can). So that means you’ll have to bunch the sail up near the top of the mast and carefully hand feed it from there and then go back to the cutout and pull the sail down from there. You might have to repeat that process a few times but should get the job done without damaging the sail. For the battens do your best to keep them on one side as you thread the sail. If they end up on the wrong side you should be able to force them to the other side by pushing on the batten close to the mast and pull the mast up to get them to flex and move to the correct side. Hope that helps :)
@superisaful
3 жыл бұрын
Best rigging tutorials I’ve found on KZitem. Please keep doing this!! ❤️
@willnicholls5
3 жыл бұрын
Thanks Isabel, appreciate that :)
@michaelkilgore9271
4 жыл бұрын
Great information that I’ve been looking for months to find basic things to know before paying for a lesson 👍👍👍👍👍
@willnicholls5
4 жыл бұрын
Thanks Michael glad it was useful
@mikethezipper
2 ай бұрын
Awesome video, straight and to the point. Love it, thanks for taking the time to make the video
@willnicholls5
2 ай бұрын
Thanks Mike
@CutBackTvChannel
4 жыл бұрын
Great tips Will :) Love from Portugal! Subscribed
@willnicholls5
4 жыл бұрын
Thanks guys!
@henrycartwright7124
3 жыл бұрын
Crystal clear!
@daanhendriks2606
3 жыл бұрын
this is fantastic. Much Thanks!
@willnicholls5
3 жыл бұрын
No problem Daan. Thanks for watching
@Ilias.12345
3 жыл бұрын
Thank you so much bro for this value information
@willnicholls5
3 жыл бұрын
No problem, glad it helped :)
@MartiA1973
4 жыл бұрын
Solid beginner info'. Who d'feck gives this guy a "thumbs down"?
@willnicholls5
4 жыл бұрын
Thanks dude appreciate it :)
@MartiA1973
3 жыл бұрын
Bought a new U/J recently and at 8:10 where the pin pops into the mast foot, mine is now a really tight fit so has to be "coaxed" in with a rubber mallet and then attached to the board. Hope it gets easier as the rubber U/J compresses.
@willnicholls5
3 жыл бұрын
Hope it gets easier, make sure the mast base is properly cleaned out there may be something stuck inside? The fit shouldn't be too tight. Feel free to send me an e-mail if you need me to take a look
@cheepchoop6402
4 жыл бұрын
Hi mate, great video. I allways use the duct tape on the connection, however two weeks ago my mast broke while just surfing in very light wind 12 knots. I'm sure the mast was properly together and it was also taped. Would this just be unlucky? Or should i contact the manufacturer? Thanks
@willnicholls5
4 жыл бұрын
Thanks dude. It depends where the break is and how it broke. If you were just sailing along in 12 knots and it just snapped then definitely contact the manufacturer. It may also be under warranty as windsurf gear usually has around 2 years. tbh it may be worth contacting the manufacturer anyway just to see what they say. hope that helps and you manage to solve it :)
@thernsa
4 жыл бұрын
Very helpful, Thank you!
@willnicholls5
4 жыл бұрын
No problem, thanks for watching :)
@nelsonenaccion4x424
Жыл бұрын
Niiiiiiiiiiiiiice
@simonparker4992
3 жыл бұрын
Good detail about the battens. Can I just ask, are extensions universal or are there separate RDM and SDM extensions?
@willnicholls5
3 жыл бұрын
Hi Simon, The extensions are separate. You can either get an RDM extension or an SDM extension.
@awaywidya
4 жыл бұрын
Silly question, but to de-rig do you just do everything in reverse, ie loosen the outhaul first? Also, do you recommend complete disassembly between use or is it ok just to take out the uphaul and outhaul tension and keep the sail rigged? thanks
@willnicholls5
4 жыл бұрын
Yeah loosen the outhaul first and take the boom off then the downhaul. I’m using my kit pretty much everyday so I leave my kit rigged just without the boom and the downhaul on. But normally at home I fully de rig my kit to get it in the car. It is better to disassemble the kit because when the sail is ender tension it can be deforming slightly and stretch.
@wimsaelens7673
3 жыл бұрын
you can put your uphoul trou the hole on the buthom of your sail so your buttom is nicer
@willnicholls5
3 жыл бұрын
DUDE! That's amazing, I never knew that hole was there. My mind has been blown, that makes so much sense. Thanks!
@wimsaelens7673
3 жыл бұрын
@@willnicholls5 i also now it for a short time
@seanhoskingbiofieldmyother812
9 ай бұрын
You lost me at 6:16, way too fast to figure out what you were doing.
@willnicholls5
9 ай бұрын
Thanks for the feedback Sean, noted for future videos.
@willnicholls5
9 ай бұрын
In reference to 6:16 I was trying to explain how I have my outhaul line setup so that it’s easy to setup each time I rig up. Not all booms are the same but if you have a boom similar to mine then the screenshot shows a good outhaul setup where a loop is made by making a knot at the fixed end (arrow 1) and at the cleat end (arrow 2). This makes it easy to put on the outhaul because all you have to do is pass the loop through the eyelet of the sail and then put the loop over the plastic knob where possible and then all you need to do is pull on the rope from the cleat end to complete setting up the outhaul. Hope that helps :)
Пікірлер: 36