Thanks Jason! I switched to Linux on several of my main machines at home that I use for ham radio... been wanting to get Winlink working on those for a while... this is a fantastic service to the ham community. Thank you sir!
@timbookedtwo2375
Жыл бұрын
I just configured my Ubuntu 20.04 laptop according to the past three or four videos, hoping to work out the kinks in my system. I did it wihout backing up beforehand. Hey, no risk, no fun. I am happy to report I had fun. Jason's instructions were as usual impeccable. Thank you. One little difference I noted. When installing direwolf the direwolf.conf file did not land in my home directory but rather in ~/direwolf/build. I copied it to my home directory, if that is important. Tomorrow I will try the whole shebang out on my HF radios (FT-891, IC-7200). I don't do UHF/VHF because there are almost no stations to contact, so I can't try out direwolf. GPS and GPS-time were already configured, so I expect to be good to go. I really appreciate all the work Jason and his assistants have put into this project. I would not have been able to do this on my own. Thank you. 73! SV0SGS
@user-gy7uz9qs7u
11 ай бұрын
Hi Jason, I've been trying for days to make this work on Mint 21. VARA and VARAFM will not launch. The problem seems to be that "vbrun6" does not download/install using wine tricks in your script. Is there a work around for this ? thanks, KA7RLM
@Kevitivity
Жыл бұрын
This is a very helpful video. Wanted to mention to any Ubuntu users out there that most of these software mentioned here can be installed via apt.
@jesi1619
Жыл бұрын
Thanks Jason for your suberb work 👍. All is working as expected on an old Panasonic Laptop 👏
@swisschiguy
Жыл бұрын
I get to where VARA HF and VARA FM install successfully, then try to run them and all I get is a spinning icon for about 30 secs and then nothing. Any ideas?
@steveshelton5884
Жыл бұрын
Thanks Jason I was able to get two Evolve III laptops converted over to LInux and working with all the tools that you presented. 73 Steve KE0VCD
@cbjessee
Жыл бұрын
In PAT MENU/Find Winlink Gateways/Download Gateway List I'm getting YAD "Grid square not set in Pat Configure File. Run 'pat configure' to fix. I do see where I've correctly entered my grid square in line 4 as "locator": "FN42fx", I tried Repair Pat Config again but no go.
@rong8955
Жыл бұрын
This is an awesome set of work. Thanks for sharing all this info. I may give it a try on my sub-$100 Asus.
@KC3WHJ
11 ай бұрын
I'm trying not to happy cry right now KM4ACK... I've been struggling with getting digital modes set up - mainly being able to send email without using the Internet. Literally wiped Windows off of a laptop, installed Ubuntu and used several of your videos to set things up. About 10 minutes ago, I FINALLY sent a Pat Winlink message over VARA HF and received 2 I'd created in my Webmail!!! Idk if you drink but I got a bottle for you if you are ever near Philly! 73!!!
@KC3WHJ
11 ай бұрын
Now if I could only get all of this to work on Ubuntu 22.04 with my G90 and Digirig... Now THAT'S a project! ;-)
@neosentry
Жыл бұрын
So, Jason, what's the recomended practice when the "a new version is available for download" button pops up in Vara HF on Wine? How does one go about properly updating to a new version of Vara on Linux?
@erikyater2215
Жыл бұрын
Came here looking for the same answer. I tried changing the filename in the vara-on-debian script, but that file must not be in the dropbox, yet. Although maybe I should leave well enough alone, patmenu2 and VARA HF have been working great for me. Looking forward to new information about this, thanks for posting James.
@Scaliad
Жыл бұрын
@@erikyater2215 I don't know, but for peace of mind, you can turn off "Allow VARA check for updates via internet" in Settings... VARA Setup...
@kd6aaj
Ай бұрын
I'm running Linux Mint on an old Dell Latitude D820. I managed to "install" Pat and Patmenu2, but I can't find the Patmenu2 shortcut in the startup so I just copied it to the desktop. Unfortunately I have a small HDD so Wine won't run because I haven't installed Windows on it, so no VARA. I already have Direwolf on here. For some reason I can't find the Pat install anywhere on the HDD (I'm a little rusty with Linux), but I can start Pat in the terminal but it want's to use USB instead of serial? How do we get Pat to work with a good old fashioned TNC in Linux. I am pretty sure it works on my windows PC and the old TNC (its a PacComm Handi Packet TNC with an DE-9 RS-232 port). Thanks! July29 2024
@hitechfl
Жыл бұрын
Note for others.. When enabling and starting the pat service, use your username for your computer (that you use to login to your computer with)... If it's different than your call sign you won't get it to run without doing this. I made this mistake by replacing KM4ACK with mine everywhere.. but on the systemctl commands it's different.
@chesty1369
Жыл бұрын
great video as usually Jason....I am hoping one day i can get my Winlink gateway over to Linux,,,
@darknoizeNL
Жыл бұрын
i am trying to get Direwolf to work with my CM108 usb soundcard with PTT for my Baofeng UV-5R. I know direwolf supports CM108 and i have the config and all working. Except in linux mint 21.1 vera, when i open up pavucontrol, i can see the levels, but direwolf refuses to start the usb device. if i close pulseaudo and replug the device direwolf will see it eventually and start normally. i think because direwolf is using ALSA, rather than Pulseaudio. Any fix for that perhaps?
@ke7uia
Жыл бұрын
Jason, I am trying to install Vara FM. I get the message " The VARA Modem FAILED to Start'. What am I missing. ths
@KeepEvery1Guessing
Жыл бұрын
$USER is an option when typing those shell commands where you need to specify your username.
@berndkonemann5049
Жыл бұрын
I have an "ardop TNC initialization failed" error. It tells me that set gridsquare failed. Syntax error. However, looking at the pat menu conf file, it is clearly there. Where do I go wrong (have used patmenu to repair pat config, no improvement). What do I need to do ? Thank you.
@waldemarmarkduszyk2756
Жыл бұрын
Hi, I have ICOM M803 (a newer version of M802). This transciver has a serial port for connection with computer USB port. I dont know how to set SIGNALINK. Do I need to connect its Radio port with the microphone port of the radio and Singalink USB with another USB on my linux box? If someone knows how to do that - please respond. Thanks MarkD
@phildurall7466
Жыл бұрын
Jason, you just made my morning cup of coffee interesting Sir! Tnx, 73 - KF6IF
@bobsegrest9444
Жыл бұрын
I get a "No such file or directory" error when I start the ARDOP modem with PatMenu2. Isn't there something that has to be configured in Pat to make this work? You probably covered this in another program, if so a pointer would be appreciated. KO2F
@calvinkutemeier393
Жыл бұрын
Is there a BAP version for use on a 32bit Lenovo S12 laptop? I thought I saw something but now cannot find it. I run LMDE on the 32 bit S12.
@KM4ACK
Жыл бұрын
I recently released 73Linux to work with x86 machines. Details in this video kzitem.info/news/bejne/z2OZyX9tq6WjZ4o
@uns3cur3
Жыл бұрын
I seem to have missed the PTT for VaraHF. I have the vara software installed but I haven't run all of the pat menu steps ( which I suspect install some pat winlink cfgs) because I have a working VHF pat setup. How is PTT done for Vara? I am bailing on ardopc as I just can't get it to decode,
@KM4ACK
Жыл бұрын
Depends on your setup. Here's one example for VARA FM kzitem.info/news/bejne/yo-PuIirb5-qhZg. In VARA HF, I have it set to VOX and PTT set to True in the Pat Config file. FLRIG is configured for the radio so Pat handles the PTT through FLRIG. VOX isn't actually used on the radio. The VOX setting in VARA is more of a "dummy" setting so VARA doesn't attempt PTT.
@uns3cur3
Жыл бұрын
@@KM4ACK I forgot that I removed the used vara stanzas from my config so I put them back and then I set rigctld -v -m 4 and it all works!! awesome content!!
@uns3cur3
Жыл бұрын
@@KM4ACK I just sent a message via KC8ZKI!!
@ke7uia
Жыл бұрын
Jason, I completed all these steps again and found that the Patmenu2 will not start VARA-FM or VARA. Yet I am able to start VARA from the START: menu.
@KM4ACK
Жыл бұрын
Take a look at the quick stats in pat menu and verify that the pat server is running
@luckyjoe1670
Ай бұрын
I am in the process of setting up Winlink. I am at the point where I run sudo systemctl start pat@kc3vqt. I get the following error message: failed to start pat@kc3vqt.service: Unit pat@kc3vqt.service not found. Thanks for your assistance.
@BernardLelectricien
Жыл бұрын
Hello there, PatMenu... I get an error message when trying to download the gateway list. ...Grid Square not set in Pat configure file... gave my grid square in manually but still fails. How is this fixed ? Thank you
@KM4ACK
Жыл бұрын
You may have discovered a bug. I'll look into it
@BernardLelectricien
Жыл бұрын
@@KM4ACK I think it may have to do with the initialization of the grid info. set grid square failed. Maybe that may send you in the right direction, as it happens also when I am on the internet, trying the same via the patmenu. Best of luck
@lw3dtr
5 ай бұрын
Hi it is possibel to do all of this but using an KPC3 PLus TNC on linux ? instead of Direwolf ?
@KM4ACK
5 ай бұрын
VARA won’t work with a TNC.
@kenithmiller2475
Ай бұрын
I am trying to do this installation on a chromebook with no success to date. Can you help?
@KM4ACK
Ай бұрын
Sorry. I don't have experience with a Chromebook
@on2mvh937
7 ай бұрын
Hi, would this work on ubuntu mate? Doesn´t seem to have many options for ham radio in the program shop...
@KM4ACK
7 ай бұрын
It should since Ubuntu is also Debian based.
@on2mvh937
7 ай бұрын
@@KM4ACK my thought also. Will have to dive deeper into it. But in the default software shop it´s a no go. And in the software app has only some ham apps available
@W4BTK
7 ай бұрын
May I modify your VARA on Debian script to pull the latest VARA modem version from the site? I know that will change in the future, but, just for the sake of installing the latest version from the start. I will keep your callsign in the script as credit to you is due. Thank you.
@KM4ACK
7 ай бұрын
You bet. All of my code is open source. Feel free to modify for your use case.
@theodoreboyer2275
10 ай бұрын
Man I am so frustrated. I get to the pat mailbox at the end, and try to connect with telnet, and it says password does not match. When I go back to the pat configure command, my password has been changed. so I fix it and ctrl s ctrl x and it still doesn't work. It is automatically changing my password.
@KM4ACK
10 ай бұрын
That's odd. Never seen it get changed in the config file. When you change it next, try ctrl+x, then "y " which will also save and exit the nano editor. Go right back in and confirm the change saved before trying another connection.
@theodoreboyer2275
10 ай бұрын
@@KM4ACK I think I figured it out. When I exit pat configure and go straight back in, it is fine. It's the step in the video where we are in Pat Menu and click Repair Pat Config. Even though I'm putting my password in correctly, it changes it in the configure file. I just need to skip the repair config step. Also, if I try to use the Pat Login-Logout button, then firefox cannot connect. I'll just stay away from those areas and use Start Modems. Thank you so much for answering. 73 👍👍
@Siskiyous6
Жыл бұрын
So Jason how did you know the localhost number for flrig?
@KM4ACK
Жыл бұрын
The short answer is it is the default port. The long answer deserves a video :-0
@nonokodog622
Жыл бұрын
I've been learning how to set this up for normal Ubuntu install on x64 machine. Appreciate the Dire Wolf walk through ! I'm curious why you use flrig and not just rigctld ?
@KM4ACK
Жыл бұрын
If you configure FLRIG for the radio and then point all of the apps (ie JS8Call, WSJTX, etc) to use FLRIG, you only need to change the FLRIG config if you swap radios. For me, that's the easiest way if you have two or more rigs.
@TheRanger53
Жыл бұрын
Jason are there other programs that should be installed before Winlink and Vara such as hamlib. I keep getting messages that direwolf will not configure. This is one of the messages, Config file line 185: PTT is only available when hamlib support is enabled. You must rebuild direwolf with hamlib support
@KM4ACK
Жыл бұрын
Yes. Some apps do need to be installed in the correct order. If you follow the series from the beginning, everything will be in the correct order. You can also just back up and install hamlib and then rebuild direwolf.
@GhostRider1974
Жыл бұрын
Everything went smoothly until the VARAFM / VARA part. I did not get the windows-like setup dialogue boxes after running the vara-on-debian script. It just finishes and takes me back to the terminal command prompt. Any ideas?
@KM4ACK
Жыл бұрын
Try running the script again.
@GhostRider1974
Жыл бұрын
@@KM4ACK Thx. I did that and it still doesn’t have the windows-like install dialogues. Will investigate further.
@williamholtman7172
Жыл бұрын
@@GhostRider1974 I experienced the same result. Did you find the issue?
@williamholtman7172
Жыл бұрын
My install is awaiting a response (see below): "unzipping VARA files Archive: VARA FM v4.2.3 Setup.zip replace VARA FM setup (Run as Administrator).exe? [y]es, [n]o, [A]ll, [N]one, [r]ename: Archive: VARA HF v4.6.3 Setup.zip replace VARA setup (Run as Administrator).exe? [y]es, [n]o, [A]ll, [N]one, [r]ename: "
@GhostRider1974
Жыл бұрын
@@williamholtman7172 Yeah, that’s what I get. I just selected A for all and tried again. Will try again tonight.
@KB5WCK_Radio
Жыл бұрын
How do I add a HamRadio menu group? I downloaded alacarte but it won't add the menu.
@KM4ACK
Жыл бұрын
sudo apt install -y extra-xdg-menus
@curryconsult
Жыл бұрын
Any thoughts of creating a Build-a-Pi version for x86 cpus like your Evolve?
@KM4ACK
Жыл бұрын
I have toyed with the idea - github.com/km4ack/73Linux
@dgcasteel
Жыл бұрын
Jason, thanks for putting these videos out. This is a great help. I started with a clean install of Linux Mint 21 and followed all your videos to this point. Everything works except PAT will not start. I get an "Unable to load/write config: unexpected end of JSON input" error. Could not get it to start as a service so I tried "pat http" and saw this error. Any thoughts? Thanks again. David KX8U
@KM4ACK
Жыл бұрын
Sounds like the config file is corrupt. Open Pat Menu->Manage Pat Winlink->Repair Config File.
@dgcasteel
Жыл бұрын
@@KM4ACK thanks for the reply. I did try that but did not work. Seems Patmenu could not find the config.json. I had manually update the file. Got Pat working.
@charlesliebow413
Жыл бұрын
whereis ardopc_64: not on john wiseman??
@KM4ACK
Жыл бұрын
www.cantab.net/users/john.wiseman/Downloads/Beta/
@johnblaisdell2179
4 ай бұрын
As usual nothing linux ever works as simple as the video does. I got as far as "cmake .." and then got a whole screen of red error. These how to videos never work for me. I'm running Linux Mint same as this video. Oh Well!
@charlesliebow413
Жыл бұрын
found it..just dumb i guess
@CWO4Mann
Жыл бұрын
Hello Neighbor, glad to see your channel and this Pat Winlink video is outstanding. 73's de N4CVX
@KM4ACK
Жыл бұрын
Thanks David. Glad you found the channel 😀👍
@TheRanger53
Жыл бұрын
Jason when running the cmake in the direwolf/build directory I get the following error; CM error at CMakelists.txt:3 (project): No CMAKE_CXX_COMPILER could be found. Tell CMake where to find the compiler by setting either the environment variable "CXX" or the CMake cache entry CMAKE_CXX_COMPILER to the full path to the compiler, or th the compiler name if it is in the PATH. No idea what this wants.
@TheRanger53
Жыл бұрын
I failed to include that this is on an old HP laptop that I loaded the latest version of Mint on. Here is the error log. Scratch that I guess it is too large to paste in here.
@KM4ACK
Жыл бұрын
try running "sudo apt install build-essential" and then try the build again.
@muisudad
Жыл бұрын
I am trying to install on ubuntu 2204. When I do the cmake I get the same 2 error you also got. One is Make Warning (dev) at /usr/share/cmake-3.22/Modules/FindPackageHandleStandardArgs.cmake:438 (message): The package name passed to `find_package_handle_standard_args` (HAMLIB) does not match the name of the calling package (hamlib). This can lead to problems in calling code that expects `find_package` result variables (e.g., `_FOUND`) to follow a certain pattern. Call Stack (most recent call first): cmake/modules/Findhamlib.cmake:55 (find_package_handle_standard_args) CMakeLists.txt:260 (find_package) This warning is for project developers. Use -Wno-dev to suppress it. When I run direwolf -p I get Dire Wolf version 1.6 Includes optional support for: cm108-ptt Reading config file direwolf.conf Config file line 185: PTT with RIG is only available when hamlib support is enabled. You must rebuild direwolf with hamlib support. See User Guide for details. Any suggestions ?? What should I try. Thanks for your get information. PTT works fine in my wsjtx config using either flrig or Hamlib Net rigctl KD9JQR
@artolson118
Жыл бұрын
Jason GOT A FAR AS VARA install however the gui doesnt present from the windows key. Here is the error 0108:err:richedit:ReadStyleSheet skipping optional destination 0108:err:richedit:ReadStyleSheet skipping optional destination 0118:err:module:import_dll Library MSVBVM60.DLL (which is needed by L"c:\\VARA FM\\VARA Install.exe") not found 0118:err:module:LdrInitializeThunk Importing dlls for L"c:\\VARA FM\\VARA Install.exe" failed, status c0000135 ^C0150:err:richedit:ReadStyleSheet skipping optional destination 0150:err:richedit:ReadStyleSheet skipping optional destination Art N2AJO
@KM4ACK
Жыл бұрын
Try running the VARA install script again.
@russharmon6635
Жыл бұрын
Jason. trying to follow your steps and when installing direwolf i am fine up to the point: "/direwolf/build$ make -j 4 error of make: *** No targets specified and no makefile found. Stop." this happened for the sudo make install also .
@KM4ACK
Жыл бұрын
double check your work. it sounds like you might not be in the direwolf directory. There's also a direwolf forum that can be helpful groups.io/g/direwolf/topics and their documentation is pretty good as well - github.com/wb2osz/direwolf/tree/master/doc
@curryconsult
Жыл бұрын
I've been following along with this series, enjoying it immensely, and busily installing everything. I'm using an HP EliteBook 840 running Debian-based ElememtaryOS. Everything was installing perfectly until VARA. Everything installed but the VARA setups don't run. Any suggestions? de VE1GU
@KM4ACK
Жыл бұрын
Try running the vara install script again. It was written for Mint but it should run on any debian based system. Also, if you take a look at the script itself, there's a link to the website that I used for reference when writing the script. That page might be useful. github.com/km4ack/pi-scripts/blob/master/vara-on-debian#L7
Пікірлер: 91