Hello, thanks for the tutorial. Do you think it's possible to add a rechargeable battery to it ? If so what is the voltage needed for this light fixture ?
@DJFrancisco
10 ай бұрын
I have never tried that, I would probably need to know where the voltage converts from AC to DJ and then measure it... That's a little more complicated than I can do
@fpvzone8522
3 жыл бұрын
If there is a transmitting light can it be wired with DMX Out to other Lights at the same time while it sends the signal? Good tutorial👍
@DJFrancisco
3 жыл бұрын
Yes, I do this all the time... I actually hook up my led uplight inside my truss so it can receive DMX, and send it up to the top of my truss to the moving head
@erickc2589
4 ай бұрын
Hi, what kind of led controller is that one on this video? looks like a sony psp
@DJFrancisco
4 ай бұрын
It's Called the Numark Orbit Controller... wireless midi device, it was really cool... www.numark.com/product/orbit
@abo7uson
5 жыл бұрын
im thinking of doing this project.. what type of moving head did u convert to wireless?
@DJFrancisco
5 жыл бұрын
chinese 90 watt generics
@djaerox7574
3 жыл бұрын
Is the also a Video Converting moving Heads? What is, if i want to go one time with dmx cable but installed the wifi module at Same time (e.g. In case my transmitter Crashs) Great Job& Video.
@DJFrancisco
Жыл бұрын
Yes
@chaliHustles
7 жыл бұрын
I have a ADJ tripar profile. how did you find 5 volts what were you looking for?
@DJFrancisco
7 жыл бұрын
I don't have an ADJ Tripar, or else I would check for you, but there are some IC chips on the broads... some will have $5v going through one of the pin... Either that or look for a 7805 transistor and that one for sure will have 5v
@djfred24
5 жыл бұрын
on the 8 feet chip you will get the 5v i have the picture i can send you for the 5v
@DHL2002
5 жыл бұрын
i want to make wireless DMX balls where thes 8 double a battiers suppling power to a DMX to led strip decoder, how would i power one of these boards with this.
@DJFrancisco
5 жыл бұрын
You can use a rechargeable battery such as the Lithium Ion 18650s or 3 AA Batteries in Series to get you to 4.5v
@visualmakersproducciones3418
6 жыл бұрын
Hi! nice video I have a query, the transmitter is a console with the wireless dmx integrated? or did you adapt an antenna of these? could you explain how you transmit? Thank you
@djfred24
5 жыл бұрын
the dmxcart cna transmit and receive itself
@DJFrancisco
8 ай бұрын
Yes
@djdnewworld
5 жыл бұрын
Can you post a link for the light on where you purchase it from?
@DJFrancisco
4 жыл бұрын
I would not suggest you buy these lights.. They are from ebay.. 4in1 RGBW led Lights..
@chaliHustles
7 жыл бұрын
also what type transmitter will pick up these receivers and type lighting program do you use for computer
@DJFrancisco
7 жыл бұрын
For the program on this video, that one is called Q+ Light show (something along the lines) I loved it but it's not 100% working with my moving heads. The other program I use now is freestyler. Most Wireless DMX receivers are transmitters as well, They are smart... if they detect a dmx signal present on the pins... they automatically transmit... if they detect a dmx signal that is already being transmitted wireless, they become receivers..
@nelsonpollard4435
5 жыл бұрын
Charlie Valenzuela
@DJBazza1968
3 жыл бұрын
do you have a link to the dmx board please?
@DJFrancisco
3 жыл бұрын
I purchased directly from china, but I can show you something similar on amazon... www.amazon.com/Wireless-Transmitter-Receiver-Modules-Controller/dp/B093FXH6W6/ref=sr_1_2?dchild=1&keywords=wireless+dmx+board&qid=1622851322&sr=8-2
@fpvzone8522
3 жыл бұрын
Can they run with Master Slave Mode?
@DJFrancisco
3 жыл бұрын
Hi FPV Zone, that depends on the light. Most lights do not run wireless dmx on master/slave. Master/Slave is not a DMX signal, but a proprietary signal. I have one company that does run Master/Slave DMX and they can control other wireless lights. But the majority do not run a dmx signal on master slave.
@nelsonpollard4435
5 жыл бұрын
The DMX pcb has a place for wire connections
@DJFrancisco
5 жыл бұрын
How do you mean?
@nelsonpollard4435
5 жыл бұрын
DJ Francisco Perez the pcb board that is attached to the DMX connectors has 3 solder pads with holes for the wire to pass through for soldering.
@DJFrancisco
5 жыл бұрын
You mean the ones pictured at 6:05 right?
@nelsonpollard4435
5 жыл бұрын
DJ Francisco Perez Yes sir
@DJFrancisco
5 жыл бұрын
Yes, you are right, I still prefer to solder to an existing contact.
@Ensoniqdude
10 ай бұрын
You need better lighting.
@DJFrancisco
10 ай бұрын
Video Is 6 Years old, I needed better Lighting, better camera, and better video editor... :)
Пікірлер: 37