Thank you great video, and you made the Nano Loco M5 so much easier to set up, rather than the crazy long manual. I was able to magnify the video a fair amount by clicking on the 3 dots (top right of browser), and selecting zoom, which will help Chuibacca below. I wonder, if on a future video, would you be able to run through what each of the modes do on the Nano Loco M5, as no one seems to say on search engines what each mode does. Having said that, the mode you showed in this video, Access Point, (where the master device serves as a router, and the slave serves as a receiver) seems to be the most versatile. Thank you again Andy Wrob (Merseyside)
@chuibacca9687
2 жыл бұрын
Recommendation: Increase the visual screen size of your browser window, to fill most of the screen...for the visually impaired, it was difficult to visually follow where each data entry point was located. Was great video otherwise, very clear and explanations were on point. Thanks!
@ForumsbyLukas
2 жыл бұрын
Thank you for the feedback.
@trashman1613
3 ай бұрын
It’s straight forward until I run into problems😂
@dekamtechsystems
3 жыл бұрын
Wow its clear and amazing
@ForumsbyLukas
3 жыл бұрын
Thanks for your feedback!
@t.a7265
2 ай бұрын
Hey there, I’m messaging from NZ and have set two of these up to get WiFi to my shed approx 30m away. I set mine up after watching another video by someone in Hawaii.. your video is also good and informative. I got mine working, but keep having the issue where it is not consistent. It stops/starts but then completely stops transmitting! I don’t know where it’s going wrong…Does the SSID and output power make a difference. I’m running off starlink internet which is great but I just need to get wifi to the shed..
@Seven-Seven-77
2 жыл бұрын
Thanks for the video. Is it OK to have a switch at each end? Just that you mentioned one end as a remote camera, any issue if the was a switch with 20 cameras?
@ForumsbyLukas
2 жыл бұрын
All is limited to the the total bandwidth. I had sites with more than 20 cameras but make sure they are not set to maximum encoding settings. Lower fps, resolution etc. to keep the low bitrate.
@nielscremer599
2 жыл бұрын
Can I connect a router to each end of the setup? A router connected to the internet to the master and a router over a long Ethernet cable to the slave device? The point being that I want line of sight between the two bridge points, but need my router to repeat the signal inside the house.... Is that a possibility? Thanks for the video! 😁
@ForumsbyLukas
2 жыл бұрын
Yes, you can. The WiFi link will be in the bridge mode, almost like a bare cable in between.
@chappie8223
2 жыл бұрын
would you recommend the nanostation mo5 or nanostation loco m5 for going 1/4 mile and using the wifi for 10 ring cameras
@ForumsbyLukas
2 жыл бұрын
Pair of loco m5's will do it no problem.
@bicak9364
3 жыл бұрын
Can yo pls give me some tips. I heave a 2 nanostation m5 and i wont conect them together from lan. I got them on ethernet, but i wont it on lan. Can you tell me how i conect them? Because when i put off a cabel from thernet they are down with conection thx
@ForumsbyLukas
3 жыл бұрын
Please check for any ip conflict.
@everythingintering221
10 ай бұрын
Hello lukas, what could cause my LocoM5 from not broadcasting wirelessly?
Пікірлер: 26