Good to know about the yellow terminal. I've been wondering what it was for
@27kmoreno
3 жыл бұрын
If I wanted to use 3-12volt LED bulbs, would i still use a 12v transformer? I'm trying to bring my grandfather's pachinko machine back to life, so I'm having to learn everything! Thanks!!!
@MagicPachinko
3 жыл бұрын
Yes, you just have to observe polarity when you use LED bulbs.
@theOutpost420
24 күн бұрын
Would you be able to show or tell me more about a Ginza's wirings , i feel like im missing something.
@MagicPachinko
24 күн бұрын
All the wiring is the same. Two DC circuits. One for ball out and another for the jackpot. They usually have power going to each circuit with a common return. Watch my wiring videos even though they are for Nishijin. Think of each circuit as a circle broken by a switch. Call me if you need more help. 585-760-9104
@theOutpost420
23 күн бұрын
@MagicPachinko thanks so much ill be working on it over the next week or so, its been tough finding any info on my exact machines so i appreciate all the tutorials and info 😊 👍
@celinasalinas8612
Жыл бұрын
This is an amazing video but could you like the wiring/ converters purchased to get the lights to work?
@MagicPachinko
Жыл бұрын
I got everything on Amazon. E10 12V bulbs and 12VDC power supplies.
@user-vi6pd6zj9q
3 ай бұрын
Hey Dan, I have 2 orange wires coming off the switch by the jackpot. They are cut or chewed into. Where do they hook up to?
@MagicPachinko
3 ай бұрын
You will have to give me a call sometime and I’ll explain it to you. Too hard to do via text. I have made a number of videos about wiring. Check my KZitem channel also.
@bstache6103
Жыл бұрын
Hey Dan! I got a kyoraku in 2019 and have been off and on fixing it up. I originally had it hooked up to a 9v with way to big gauge wiring. (Didn’t know what I was doing) where did you get the adaptor and wiring for the 12v wall transformer?
@MagicPachinko
Жыл бұрын
Amazon! 18ga wire, A10 bulbs (12v), 2A fuse and the 12VDC.
@bnihockey1425
2 жыл бұрын
Hello! I recently found a 1973 Nishijin Super Deluxe while cleaning out a basement and it is fully complete expect for the power supply. I read that you use a 12V wall transformer, do you have a link you could post for me? Thanks!
@MagicPachinko
2 жыл бұрын
www.amazon.com/dp/B07C8BD773?ref_=cm_sw_r_cp_ud_dp_4KPS40BAKE3CAQJ4YFFN This is what I use. You can buy them single. I cut the connector off and wire direct into the machine.
@jeffbattenberg2394
2 жыл бұрын
Hi Dan. Thanks for the video! Restoring a 1960's vintage Nishijin. It has no buss. Currently, all bulbs have power when the leaf switch is NOT activated (leaves not touching), and turn OFF when the leaves touch. Also, there is no leaf switch for the low ball indicator. Are you aware of a place that I can purchase a leaf switch for this machine?
@MagicPachinko
2 жыл бұрын
Sounds like something is wired incorrectly. You can use micro switches in place of leaf switches for the ball out circuit. If you want to talk about it, visit the website and leave your contact info.
@alexandergreco3474
2 жыл бұрын
Mine is broken where do I buy this? Thank you
@MagicPachinko
2 жыл бұрын
Do you mean your lights don’t work? I can help with that. Contact me directly.
@markwendell1328
2 жыл бұрын
Hey Dan. Working on a 70s nishijin rebuild. I have power keeping the low ball light on, which is weird because it doesn’t go off even when the leaf switch isn’t touching .The jackpot lights won’t come on at all, even when leaf switch is touching. I’ve tested all the bulbs, they all work. I’m wondering if it’s the buss or cables that have gone bad? It’s a pretty dusty machine, but functions as it should aside from the lights. Any advice would be much appreciated! Thanks
@MagicPachinko
2 жыл бұрын
Sounds like you have a short somewhere. Go to my website and leave your phone number on the contact page. I’ll call you right away and we can figure it out.
@brianscollon6023
2 жыл бұрын
Hey have this pachinno machine can you put a list up or get me a list on what i need to order to rewire the machine to get in workin order has all parts you work with in your video i would like to replace all wires and bulbs the machine is in great shape but wire and bulbs are not in great shape
@MagicPachinko
2 жыл бұрын
Contact me via my website. Leave your phone number and I’ll give you a call. www.magicpachinkorestorations.com
@markgreco1962
2 жыл бұрын
Wouldn’t it be better if the screw area of the bulb be negative and the end tit be positive? New subscriber
@MagicPachinko
2 жыл бұрын
It’s a DC circuit so it can be wired either way.
@markgreco1962
2 жыл бұрын
@@MagicPachinko thanks
@chameleoned
3 жыл бұрын
Hey Dan love your videos! Finishing up a single shot Heiwa rebuild, my first machine, and one of the three lights stays on all the time. The center jackpot and lowball light work just as they should but this other light at the bottom right of the machine is always on. I don't know what the purpose of this light is so I can't tell if it's a bad switch or that it just is to indicate power on? Kinda hard to describe without showing you a photo- but ever seen this in your restoration practice? Thank you!
@MagicPachinko
3 жыл бұрын
Send some pics to magicdan@aol.com
@theOutpost420
24 күн бұрын
Are all your leaf switches open they get bent quite easy and can cause a light to contantly stay on. Best of luck!
@chameleoned
23 күн бұрын
@@theOutpost420 I don’t remember the issue but think it had something to do with the wiring. This post was from 2 years ago!. I ended up replacing light sockets and adding LED tape on the inside. Looks great and no issues since. Thanks for your idea
@theOutpost420
23 күн бұрын
@@chameleoned nice to know you found a solution that works for you.
@alexandergreco3474
2 жыл бұрын
Where could I buy the wiring layout
@MagicPachinko
2 жыл бұрын
Go to my website and leave your contact information. I can call you and send you some info about wiring. www.magicpachinkorestorations.com
@user-mq7bs9bl7p
3 жыл бұрын
Have a 77 Monako Okumurayuki with a simple circuit board that hasd 3 bulb sockets and a jackpot leaf connecter soldered through. 2 lights are wired to the jackpot but only 1 appears much dimmer than the other. The low ball lights up as expected. You can view the video here: I'm wondering if that problem bulb is somehow in series, rather than parallel. kzitem.info/news/bejne/uYOe3JmbsWqImKQ
@MagicPachinko
3 жыл бұрын
Kinda hard to tell , but I e never seen series wiring on a machine. One light should be “low ball” and the other two would be “jackpot”.
@user-ky4fd9ok4g
2 жыл бұрын
На сколько вольт лампочки ? Потому что их 4 штуки , я хочу подать 12 v
@MagicPachinko
2 жыл бұрын
Translate?
@user-ky4fd9ok4g
2 жыл бұрын
@@MagicPachinko how many volts did the bulbs use.lwant to supply 12 volts to 4 bulbs , may l need a current limiting resistor?
@MagicPachinko
2 жыл бұрын
@@user-ky4fd9ok4g When the machine were in the parlors, the lights ran on 10VDC. I use 12VDC wall transformers on all my restored machines. I also replace the original bulbs with 12V E10 bulbs. Unless you change the wiring, you won’t need any resistance, unless you switch to LED’s.
Пікірлер: 38