Great mechanic and welding skills but it seems like this is a lot of work for such a small chipper. Wouldn’t it have been better to make it about three times the size to handle large diameter branches?
@FixItYerself
5 жыл бұрын
Holy Moses. Those blades mean business; I Cant wait to see em in action
@jasonbrown7258
6 жыл бұрын
When you cut the center hole for the bearing plate you could have used a holesaw in the drill press or chucked the plate in the lathe useing the 4 mounting holes.
@tartorstyx5104
3 жыл бұрын
What do you attach this to? Electric engine by belt? Gasoline engine hooked to shaft?
@sebastiannielsen
5 жыл бұрын
Just 2 bolts per blade? you need more! Those bolts will snap, theres tremendious forces involved in a Wood chipper. Would suggest at least 4 bolts per blade.
@MPavlenko
6 жыл бұрын
сначала сверлил, потом болгаркой обрезал и в итоге выяснилось что есть ацетиленовая горелка. Вопрос А сразу горелкой вырезать не смог?
@user-hc8ow5mu1l
5 жыл бұрын
Горелка предназначена для пайки или сварки! Для резки используют резак!ЭТО РАЗНЫЕ ИНСТРУМЕНТЫ!¡!!!!!!
@user-ct7oc9zq2r
5 жыл бұрын
Иначе видеоролик коротким получится.
@spoonforthought3534
4 жыл бұрын
Hey man you did a good job on this. Why did you go for narrow design with long blades and not the drum design with staggered blades? I don’t have the eqiptnent to work on sheet thicker than 1/4” so have too gone with this arrangement but a little smaller, using pillow blocks rather than flange bearings for ease of adjusting cutting height. It seems all the drum designs are direct drive off motor.
@davidschwartz5127
6 жыл бұрын
I want see it in use.
@paulk5311
6 жыл бұрын
wanted to see more. like what powers it and how is it affixed to whatever you are putting it in or on. like it is it is just a box with a fancy spinning shaft and blades. looked for link to part two but did not find one. because of that i have to give this video an incomplete.
@bronce196
5 жыл бұрын
Saludos al amigo de Cypsmen el video esta muy bueno lo unico mal que encontre es tu seguridad usando la pulidora sin proteccion para tu nariz te recuerdo de que los pulmons no se venden en la ferreteria o en la farmacia pero el equipo para protejerte si cuidate. Te hablo por experiencia de mi padre el soldaba usaba la pulidora etc y sin proteccion para su nariz y murio victima de una enfisema pulmonar , una enfermedad muy triste sus ultimos dias los paso pegado a una maquina oxigenadora. Su mejor mensaje fue bien claro antes de morir y nunca lo e olvidado me dijo al usar maquinaria y bregar con cosas toxicas , fiberglas etc cuidate y proteje tanto tu vista como tus pulmones.
@johnvgig
5 жыл бұрын
All that great work snd you didn’t show us in operation????????????????
@marioforieri8529
2 жыл бұрын
Does it work?
@evilraccoon6538
6 жыл бұрын
Wood Chipper with 1 shaft are not really good. Just because it can cut about 2-3 cm based on wood density. Wood Chipper with 2 shafts are really better. Can cut much more, up to 6-8 cm
@mattseymour8637
5 жыл бұрын
How do the 2 shaft ones work?
@colincrooky
6 жыл бұрын
I don’t think this will work - it will probably need a shelf with blade to provide a space for the chips to shear. Otherwise it will jam! Unless you show otherwise. P.s please don’t take your shirt off again!
@benjamindemontgomery6317
4 жыл бұрын
workout schedule. you are pretty shredded.
@davecox900
Жыл бұрын
Can you do a small one that can run on 240v for a home workshop
@ionparnete1552
3 жыл бұрын
Sunteți extraordinari
@Holy_Russia_will_win
4 жыл бұрын
надеюсь вторая версия уже была с ножами под углом30-40 градусов , вместо 90 градусов на валу. в таком положении ножи будут принимать удары на плоскость а не на острие.не работай без перчаток.
@domeniconicolini1125
Жыл бұрын
Ciao volevo sapere se questo rotore di taglio è in vendita. Quanto costerebbe? Grazie!
@ВикторМалыгин-с2щ
5 жыл бұрын
где практическое применение этой поделки? Или это, чтобы было, на полке для поделок?
@djadjazhora
5 жыл бұрын
Виктор Малыгин это главная деталь в измельчителе веток на дрова! Отличная штука с бензиновым движком!
@brianquinn6597
4 жыл бұрын
Please don't wear gloves or loose clothing around rotating machinery. That is an excellent way to lose a body part.
@Accumulator1
5 жыл бұрын
Should have done your welding without a shirt. I found that wearing only a t-shirt leaves tan lines on the upper part of the arms after the radiation burn heals.
@Accumulator1
3 жыл бұрын
Forgot the keyway in the shaft. blades stick too far which increases vibration.
@leonunesalmeida9069
3 жыл бұрын
you look great
@qwerty29456
3 жыл бұрын
Ugye fogalmad sincs a szerszámok használatáról?
@komnata519
5 жыл бұрын
Congratulations on your work. I would like to know if I can buy a wood chipper. Thanks!
@willgodwill899
4 жыл бұрын
Home made?
@denisloughman1067
6 жыл бұрын
let us see this thing working
@rafaelgandia5957
5 жыл бұрын
un procedimiento para un buen uso, Me darias las midas ( gracias.)
@odonion1
5 жыл бұрын
Na ja, Löcher bohren um danach trotzdem mit den Winkelschleifer auszuschneiden, Acetylen Brenner kann man auch als Plasmaschneider benutzen, und ob das Zeug funktioniert wissen wir auch nicht. Maximaler Zeitverlust.
@pq1077
2 жыл бұрын
Hello, what are the dimensions of the blade?
@messenger8279
5 жыл бұрын
I think it will jamb as there is no shear plate. Plus depth of cut is extreme with no feed control. We need to see further how this performed. Its not how chippers are normally made.
@Byndy95
6 жыл бұрын
please make a video, how its works!?
@ronnieg6358
6 жыл бұрын
Yes the proof of the pudding. . . . . . . . I notice you put your shirt on before welding!
@danielramirezcruz.2209
6 жыл бұрын
Good work. thanks
@michalloz18pl74
5 жыл бұрын
Jaki odstęp noża jest od podłoża gdzie będzie przecinana gałąź? Z góry dzięki 😉
@Cypsmen
5 жыл бұрын
Jeżeli to możliwe to odstęp powinien być jak najmniejszy. Pozdrawiam.
@gabrielolichwiruk4211
5 жыл бұрын
W profesjonalnych rębakach 0.2 mm
@ПашаИзвеков-г4н
6 жыл бұрын
А тест драйв чё не удался? Зажевало ветки ?
@user-pj2ru7uw5g
6 жыл бұрын
Не сверлите заготовку держа ее в руках! у меня как то вырвало из рук при таком сверлении, разбило пальцы до кости
@user-wc5bw6gz2w
5 жыл бұрын
на уроках труда в школе видел как однокласнику пальцы распарола когда сверло закусило....Та и поделка вышла непрактичной по факту у автора
@user-mf1pf7eo3o
5 жыл бұрын
Θρυματιστης κλαδιον τσουντανης
@bucksmith9035
6 жыл бұрын
why did you cut out the center with a grinder after you drilled the four holes why not skip the four holes and cut out the center with the grinder ????
@Cypsmen
6 жыл бұрын
I had thick steel and later it was easier for me to cut off the middle, grinder is not a laser.
@bowlweevil4161
5 жыл бұрын
holes did not have to be square, just cut them out with hole saw. lots cleaner and quicker
@osipgraphman4246
5 жыл бұрын
Я вот думаю почему у нас напряженка? Просто там левшей судя по сварке, сколько у нас правшей, руки пожимать не получается.
@coburnlowman
6 жыл бұрын
What was that ,that you used for the blades? I need one of these to chew up sawmill slabs. I have some half inch x 4 inch mild steel bar stock that I thought about making the blades from but I'm afraid mild steel will bend at the cutting edge.
@damonjenkins2185
6 жыл бұрын
i think it was a leaf spring
@eCitizen1
3 жыл бұрын
Death machine waiting to be powered up. (see video #3)
@rybakrybak4020
2 жыл бұрын
Radziłbym zrobić mocowanie noża na 3 śruby.
@Gkir1
3 жыл бұрын
Whats the size of the square middle shaft
@Cypsmen
3 жыл бұрын
The size of the square shaft on which the cutting knives are mounted is 3.5 cm wide, 3.5 cm high, and 12 cm long. Greetings.
@bbglas007
4 жыл бұрын
Hey mate, where did you source the center axle piece?
@ethanelectric1024
3 жыл бұрын
lathe
@kandiahjegatheesan3906
Жыл бұрын
Super
@miltondanilomanzanomeneses5606
4 жыл бұрын
Para que sirve eso??? Para moler que??
@user-ns1hs4kq9c
5 жыл бұрын
Мне кажется или на самом деле нож один не той стороной стоит
@ton-cta1270
6 жыл бұрын
ลองเครื่อง ..ให้ดู ด้วย ครับ นายช่าง 😅😅😅
@user-vt3bc9bw7k
6 жыл бұрын
Супер! Молодец!
@antoniolamonica520
2 жыл бұрын
E possibile sapere le misure ???
@jasonjohnson6216
2 жыл бұрын
Good thing u took ur shirt off. Now everybody knows u work out
@JeanPhilippeRamassamy
5 жыл бұрын
Great ! Good job !
@gordonkirby3259
5 жыл бұрын
Good Luck
@solinjosecarreno3141
5 жыл бұрын
Oye donde comprastes esa mascara para soldar .. jajajajajajajaaj
@JeanPhilippeRamassamy
5 жыл бұрын
Hello... Can you send me the sketchup project please ? Thank you for advance
@craighanson2983
6 жыл бұрын
Dude use the vise
@davidllamodelgado497
5 жыл бұрын
Según tu q cargada isistes
@edilbertovarona4062
6 жыл бұрын
Para que sirve esa herramienta
@AOZMONSTER
6 жыл бұрын
9 minutes of "2x playback just isn't fast enough"
@ranukkhan6626
2 жыл бұрын
Membuatnya beneran. Sayangnya tidak diuji kerja.
@luisgamarra8836
5 жыл бұрын
cuanto esta molino de granos
@Pileits
6 жыл бұрын
That darn music just ruin's an otherwise good video...
@26548372
6 жыл бұрын
а в работе
@NghiaLongkb
6 жыл бұрын
Tuyệt vời quá
@joaoqpapelaocoisavelhapidi6175
5 жыл бұрын
Ai bombado gostei do seu trambalho bastante extrovertido parabéns. manda um alo ai, te dei um joia,e vou me inscrever no seu canal Manaus AM brasil
@szabolcskun6616
6 жыл бұрын
Szia.működéséről nincs video?hogy dolgozik?
@miauuuu5987
5 жыл бұрын
Szabolcs Kun van róla videó
@jeanpierredupont9051
3 жыл бұрын
Met des gants quand tu soudes
@mariusz3468
Жыл бұрын
Masakra 😮 Tam BHP to nie istniało,takie wiertło by mogło dużo krzywdy narobić...dobrze że ci nie obruciło i łap nie pocieło,śruby zamiast wzmacniane to zwykłe i to bez podkładek sprężynowych he i jeszcze to trasowanie pod otwory......oś zmierzona na pałe🤦
@kobusklaassen8943
4 жыл бұрын
Plans? Anybody?
@timeaczene4369
Жыл бұрын
Madein kokler
@daviddanielacunabautista7117
5 жыл бұрын
Para que sirve
@leventdogan3762
6 жыл бұрын
Kardeş bundan banada yaprmısın
@matzigalarce4982
5 жыл бұрын
Me gusta el pico y era
@НиколайСердюк-ф7б
5 жыл бұрын
Инструмент есть-ума нет.
@spaceape3292
4 жыл бұрын
this is no home made. no regular home has that kind of equipment.
@ramilekis-ing8987
5 жыл бұрын
you don't wanna show us that it won't wo.. .
@Shitflicker
6 жыл бұрын
Working?
@kootvanzyl8250
3 ай бұрын
Nobody is interested in how quick you work or fast forward. Useles video without measurements and parts specs.
@user-wv5iv4jd2c
6 жыл бұрын
Зачем большие отверстия сверлил?
@dusicamihailovic2316
2 жыл бұрын
Moze neki kontakt
@tasheeralam2186
6 жыл бұрын
Won't work.
@user-zn6mc9qe5p
5 жыл бұрын
Tasheer Alam Х
@daviddanielacunabautista7117
5 жыл бұрын
Pero que hace
@user-lk6gm4us9p
6 жыл бұрын
Что это?
@juliovera3826
5 жыл бұрын
Y que hace esto ?
@oscarpedrozo6013
5 жыл бұрын
julio vera picar ramas y hojas de árboles
@LDCBIG1
6 жыл бұрын
Haha, a twig chipper, maybe?
@databang
4 жыл бұрын
(╬ಠ益ಠ) You can’t even fit a human skull in it, pointless!
@deletethis5489
2 жыл бұрын
too much side clearance
@mirob5743
5 жыл бұрын
facet nie pokazuje tego co jest istotne :/
@shannonamend
4 жыл бұрын
My husband used these plans from woodprix and he's very satisfied. However. I love Yours !
@user-pc6tc3ti3i
5 жыл бұрын
вот продолжение kzitem.info/news/bejne/t31jqICccKuApYY
Пікірлер: 122