I would request the engine turned off first before stepping close to these blades 😁
@rich.trails
4 ай бұрын
Serious machine
@skuresture
4 жыл бұрын
Is that a jenz chipper? I am pretty sure we manufacture those exact knifeholders at my shop. If you want good price on spare parts contact me
@Jimo225
3 жыл бұрын
that screen seems most ingenious to me. it looks like its designed so that each layer is raised on one another to create a new anvil at each level. or am i wrong in thinking that's the purpose of the design>?
@RODALCO2007
8 жыл бұрын
Expensive exercise when rebar hits the blades. Nice machine.
@bodders1029
5 жыл бұрын
re bars are not that bad...100mm bar is very different!
@user-dv6sj2tg1b
4 жыл бұрын
Цікаво з якої сталі ножі були зроблені..?
@aperson9456
7 жыл бұрын
No maintenance needed. That shit should remain that way.
@user-bu7ty3yz8n
5 жыл бұрын
Жаль нет магнитного датчика... :(
@alexanderdraws6593
8 жыл бұрын
Warum ????? Der Kumpel fährt halbe Belegung und hat statt der Abdeckplatten bzw auch Blindmesser genannt , die Messerhaler für volle Belegung drinnen. Ist doch rausgeschmissenes Geld ! Der Verschleiß an den Haltern is doch Wahnsinn !
@leonardomigot4165
5 жыл бұрын
hell what a mess on the chipper
@cditzler6313
3 жыл бұрын
thats awesome easy fix very little down time looks like can be replaced with cut blades from motor grader
@MC-pg2ko
10 ай бұрын
No way would I be near that drum with the motor still running! 😱☠
@blondewoman1
4 жыл бұрын
Une barre à mine se cachait parmis les bouts de bois.
@MAXIPlywoodLilydale
6 жыл бұрын
How come not all blades are being used, there are several pockets empty?
@bodders1029
5 жыл бұрын
i would imagine the video was edited in such a way that it looked like he left them out but in fact probably didnt?
@verteup
5 жыл бұрын
Don't need em all. Some are spares.
@samkom33
3 жыл бұрын
@@verteup its not just spares. if you add all the knifes thats possible you cut shorter-smaller chips but use more fuel on same logs
@mattseymour8637
4 жыл бұрын
Those blades are quite chewed up
@onedayagogo
Жыл бұрын
aha! so this is where rebar comes from. i knew it...
@cantororeidagambiarra
Жыл бұрын
Top de Mai's essay markina
@juergen07091973
5 жыл бұрын
Tja, jetzt stelle man sich mal vor, da wäre richtig Eisen reingekommen und nicht so Puddingeisen.... Mal so ne 200mm Schraubenwelle zwischen die Stämme schmuggeln....
@michalkotulak4948
6 жыл бұрын
Hello,where i can buy this impact wrench?
@bodders1029
5 жыл бұрын
Ingersol Rand i think was the brand
@craigschiller1599
5 жыл бұрын
Doppstadt AK430 eats metal all day long.
@bodders1029
5 жыл бұрын
yes because its a shredder not a chipper!
@oleksiy.tryfonov8
8 жыл бұрын
The fittings, not good for scrap metal shredders too)
@anniehegon9470
7 жыл бұрын
Oleksiy Tryfonov faire un faut plafond avec poutre apparante
@user-vz9yr7wc7k
3 жыл бұрын
Belarus 2020 Zabudova
@user-ko6iw2mn3f
4 жыл бұрын
Если б это случилось в России-я бы не удивился.)
@realstrannik
4 жыл бұрын
Святой валежник уничтожают ироды.
@user-bl3xi2bi6w
4 жыл бұрын
@@realstrannik 😄😄😄😄
@MrJeff832000
7 жыл бұрын
BBBBZzzzzzzzzzzzzzzzzzzzz in he goes lol
@scottpecora371
5 жыл бұрын
Ok perhaps I'm naive and ignorant but for the obvious cost of this machine not even factoring in the cost of repair and down time I think it's absolutely redictculess there isn't a metal detector to detect and stop this very thing from happening. I would think it's a given that you're going to encounter metal bars, brackets, spikes and God knows what else when shredding this type of mixed material. To not have some form of metal detection that will automatically stop the machines feed mechanism and alert the operator so that the shredder can be stopped and the feeder reversed so the operator can then wand the material to find the metal is stupid. Theres no reason you can either create a non ferrous passage, or utilize xrays, or other options where any metal will stop the feed and alert the operator. Hell, the first couple times it alarms it will have paid for its self. Oh an you might want to consider editing out the idiot with the cigarette dangling from his mouth yelling "Rebar!" Great company image, probably the founder!
@bodders1029
5 жыл бұрын
there will be a reason. those blades are only a fiver and takes about 30mins to do whats hes just done. i have a very similar Jenz machine myself. on a forage harvester the area before the knifes is stainless steel. i wouldn't want my machine stopping for a nail if it did it would be creating exactly what you are trying outline above. just a thought
@blondewoman1
4 жыл бұрын
Scott you are right, you are naive and ignorant
@henrikaki5883
4 жыл бұрын
Steel is really not that big of an issue. I mean most of the time you hit rocks or any kind of unclean wood, which the metal detector cant get anyway.
@Jimo225
3 жыл бұрын
i been saying the same thing for years. These guys will spend a half mil on a machine but wont' spend an extra 20,000 for some sort of metal prevention.
Пікірлер: 43