Even though this post was two year ago, I finished my job today according this video step by step. I watched many times for practicing, Thank you!
@jackbrown3298
3 жыл бұрын
Class video, never done one until today - followed it step by step. Thank you very much you got me out of the shit today and I learnt a thing or two.
@advancedboilertraining
3 жыл бұрын
Glad it helped!
@Breeman-gv5rr
9 ай бұрын
Hi, Indeed a great video, and very well put forward! ...the only thing I did notice, when handling the main body, the small valve came out and went under the boiler unit, though you did find it and placed it by your grease tin! ...if this boiler is to be used again, this will need fitting! ...again, great video.
@howard8814
6 ай бұрын
Whete does that bypass restrictor go please struggling to figure it out
@danielwilll
2 жыл бұрын
As a installer not a breack down engineer I was able to follow this video and do the job thanks again
@teachweb69
3 жыл бұрын
Thanks so much for these videos I really wasn't sure whether I could do this job as it looks quite intimidating or so many connections but with the help of your video I got it done took me about 6 hours but I got it done I did do some other pipework for a power flush so I'm going to do tomorrow
@dannybottomley3560
2 жыл бұрын
really helped me there pal thank you took me 3 hours to do before and 45 mins to do watching this thank you
@advancedboilertraining
2 жыл бұрын
💪
@vishalchain
2 ай бұрын
newly qualified as gas registered . and first job is this leaking. watching this hope i will be ok 😂. thanks for great video
@jacko2815
6 күн бұрын
How did it go
@vishalchain
6 күн бұрын
@@jacko2815 great! thanks for great help. :)
@liamh2467
Жыл бұрын
Got one of these to do tomorrow. Been told they're a pain. Ty for the vid m8 😊
@gurpreetrandhawa7853
Жыл бұрын
Changed my first one on Friday thanks to this video! Only thing I did differently was remove the cold pipe first before doing the pump clamp etc which was a lot easier, thank you again!🫡
@simonnoon8923
2 жыл бұрын
Brilliant video, my return manifold is leaking, so this is really helpful.
@johnmoore3569
2 жыл бұрын
Really great video, takes the guessing out of what to do next. Had to give a recent job over to someone else as I didn't have access to the video. Now I would be far more confident to attack a manifold replacement.
@andymholmes
Жыл бұрын
Thanks for sharing this mate. Absolute legend
@lukeframpton3671
9 ай бұрын
Legend just fixed my outlet manifold 🤟👍
@pauldavison7138
3 жыл бұрын
Hi Notice u have had a couple of criticism comments . Do not get discouraged by the ignorance of some people. The only way to learn is by some one teaching u or self learn. So get an old boiler and strip it just the way ur doing cheep up the good work My only advice is there’s always a tool which makes ur life easier to do the job so invest in that tool
@advancedboilertraining
3 жыл бұрын
Hey Paul, thanks for the support. Yeah that’s one thing I’ve learnt over the years, you’re only as good as your tools.
@leejones6579
3 жыл бұрын
Great video, wish l seen it before, don't my first r h b last week but took out left hand out aswell as one unit with pump attached, took a while to realise the orv was stopping the unit from coming out .Still got the cuts to show for my troubles 😂🤣
@advancedboilertraining
3 жыл бұрын
Oh no😂 you’ve just got to love Worcester 🤷🏽♂️
@jamesd755
2 жыл бұрын
If you remove the bypass pipe from the return manifold ( rather than the left side of the block), you don't need to remove the water pressure gauge or the expansion vessel braided hose from the pump body. Just pull the pump off the return manifold and sit the pump where the condensate trap normally sits. This came from our tech, who said you can cause damage when removing the pressure gauge and braided hose. I did my first return manifold 2 days ago and did it this way and it went without a hitch. Your video was a huge help, mate. I only had to watch it twice and was able to change the return manifold in good time. I've subscribed to your channel and will get a look at your other videos 😊
@marklegallienne6569
Жыл бұрын
Excellent video, well explained
@advancedboilertraining
Жыл бұрын
Thanks Mark!💪
@haroonali9018
3 жыл бұрын
Love these videos, keep them coming 🙌🏼
@advancedboilertraining
3 жыл бұрын
Thanks Haroon!
@muhammedyusuf5448
2 жыл бұрын
Nice one haroon
@ispearo
2 жыл бұрын
What a Brilliant vid....Top Job! Helped me out loads.
@chrishay8385
Жыл бұрын
Good oh I will be doing this today,thanks for that sir
@advancedboilertraining
Жыл бұрын
Good luck!!
@salam238
2 жыл бұрын
Thanks for your help and efforts.
@herrklamm1454
2 жыл бұрын
I had an absolute nightmare with one of these earlier today. I found it almost impossible to get everything lined up again. When I finally got everything back in position and tightened up again, I turned the mains water on and water was still coming out of the heat exchanger/return unit connections. I had to leave it till tomorrow. Absolute pain in the hole.
@HarveySanderson-uv3sz
7 ай бұрын
Do you not need to take bypass restrictor out of old manifold and use in the new manifold
@jockster5525
2 жыл бұрын
Top man..much appreciated 👍👍👃
@richardhodgson7443
3 жыл бұрын
Great video 🙏 thank you
@neliusgribben4738
2 жыл бұрын
Brilliant video!
@dazl7954
2 жыл бұрын
Later type unit as the longer syphon, new type fan fitted, overall that visually looks in good condition still, no visible excessive heat damage to the heat cell, and easier when they are dry too. good vid tho. Nice dark orange staining on the inside of the pump connection part of the return unit, and rear lower seal, defiantly a water quality issue on that system it was fitted on.
@nathanm6577
2 жыл бұрын
Not a bad example. You did miss a few tip points in my eyes. But I suppose that's because it was a scrap boiler that's not going to be water tight again. But not a bad reference for someone who hasn't done them before. Just to say, I've changed hundreds and hundreds of these. So I do know what I'm talking about
@rickjohnson8782
2 жыл бұрын
Can you do mine . Based in Manchester
@frosty_soda
Жыл бұрын
Whats the tips? Haha
@vishalchain
2 ай бұрын
tell up plz.
@Morecocksthanhands
Жыл бұрын
Your solenoid looks really high.. mine looks really low.. I commented on yoir other video just. I replaced the right hand unit/turbine, refilled and I've got a mostly off blue light and a 2 flash red. No ignition. Its locked off... i followerd everything you said.. Any ideas, Sir?
@asay88
2 жыл бұрын
Like the video mate. Subscribed waiting for more videos
@15blueian
3 жыл бұрын
Brilliant vid helped me out so much👌 after fitting new manifold flow on central heating gets hot when run dhw the pipes hot but not radiators. Had new diverter on new manifold could this be sticking?
@IteNifalip
Жыл бұрын
The most disastrous boilers to challenge a part
@charliewillis8527
9 ай бұрын
It's just a case of the more you work on them the easier it gets I love working on them and know them inside out
@lostinthoughtscalminsilenc8167
2 ай бұрын
I don't see much reason to take gas pipe out? Can make can of worms
@damirhusic1366
3 жыл бұрын
how on earth did you put that return pipe back in so easily, the one under the drain off, took me a lot of sweat, after about 30 mins I gave up and used the original o ring and still it was a right pain
@advancedboilertraining
3 жыл бұрын
Did you use grease? Sometimes fairy (not ideal) can make it easier
@damirhusic1366
3 жыл бұрын
@@advancedboilertraining used all that stuff, no joy, in the end I used the original o ring and used that retaining clip to keep one side down whilst I pushed the other one in. Right pain.
@teachweb69
3 жыл бұрын
I have problems with this as well full stop for a start it wasn't easy at all to get the metal bit back into the right-hand block and then when I did and I mounted the right-hand block when I tightened the bolt onto the frame it seems or it looked as though it was pulling the o-ring back out again so worried it was going to leak
Пікірлер: 52