Your system is amazing. Feels like there is always a new layer of functionality to discover.✌️ Thank you for the work you put into this👍
@Latvian3Dman
2 жыл бұрын
Your works are impressive. Love and dedication, I guess. Respect.
@TheDIYGuy999
2 жыл бұрын
Thank you!
@tejastatte3982
2 жыл бұрын
Good job man 👍🏻. Impressed by your work. And I have a request - "Can you make the sound system with accurate sound of wheel loader, backhoe loader, etc? Because, these vehicles sound different than truck and truck sound doesn't suit on them. So please what's your answer please reply...
@meatman9570
2 жыл бұрын
Hello, I have a problem with the micro rc transmitter in the serial monitor, it says Nrf24 disabled, how do you solve that?
@bambangst1680
2 жыл бұрын
mister, may i ask about my micro rc remote there is a problem, i want to ask for help, when the light mode on the micro rc remote turns on the engine sound up and down by itself and the horn turns on and off by itself. thank you
@TheDIYGuy999
2 жыл бұрын
You need to use momentary push buttons according to: github.com/TheDIYGuy999/RC_Transmitter/blob/master/3buttons.jpg
@bambangst1680
2 жыл бұрын
@@TheDIYGuy999 I've used the push button for a moment according to the picture, but when I turn on the headlights, the engine starts to go up and down irregularly, and when I program the auto light, the engine sound is irregular. Does the push button momentary value have to be reset in the program? thanks mister🙏
@cwpt2004
2 жыл бұрын
Thanks for sharing this system. I'm having a little trouble with my three buttons. (pulseWidth[5], 1000) seems to be button 2, (pulseWidth[5], 1850) button 2 and (pulseWidth[5], 2000)... but what triggers (pulseWidth[5], 1150) to change lightsState? I couldn't find the answer myself, but I didn't need button 2 to stop the engine ( I am using momentary button) so I change 1150 to 1800... Funny thing is now I can cycle through light states but the system goes a bit crazy at about light state 5 (servos twitching and horn on/off like a car alarm! I am sure I will work it out eventually but if you read this and have any ideas I would be very grateful. [It's about line 3285 in main.cpp if anyone else is curious]
@cwpt2004
2 жыл бұрын
I have rebuilt the system using your instruction for the Arduino IDE (i.e. v1.04). Everything is working fine now and above fix for three buttons works fine. It looks like you intended this channel to operate with four buttons, but the wiring diagram shows three?) Anyway, it works! I suspect that there was a problem with my board definition, or associated settings, in Visual Studio Code. I'm new to PlatformIO, although my efforts with the Rx/Tx arduinos worked fine in VS Code. Which board definitions are you using for VS Code/ Arduino at the moment ( I notice v1.05 is quite old now, do any newer ones work?) I added a trim function to the Tx menu and moved vehicle select onto a second level menu (away from my fat fingers!!)... this has freed up two buttons on the top level menu which I think I'll use for indicators.
@yuby985
2 жыл бұрын
Good job…
@frenkkotarigan
2 жыл бұрын
Can we activate hazard on automatic indicator mode?
@TheDIYGuy999
2 жыл бұрын
You can use CH11 as adjustmentsRemote.xlsx says
@frenkkotarigan
2 жыл бұрын
@@TheDIYGuy999 tq🙏
@frenkkotarigan
2 жыл бұрын
in as adjustmentsRemote.xlsx ch11 is not available hazard its not working when in "auto indicator"mode is there i must change in the main code?
Пікірлер: 18