For anyone having issues getting the lens to turn and break the glue free, take off the front cover and then run a blow dryer across the front of the camera in a circle motion. Then try to turn the camera with some pliers. This worked for me since I had a stubborn lens.
@nihonsuki
2 жыл бұрын
Thank you for these excellent instructions! I got a refurbished camera from Wyze which was actually set the way you wanted it but distant objects were out of focus. Rather than go through the hassle and delay of sending the camera back, I followed your instructions and adjusted the focus myself. Plastic jawed pliers slipped on the lens mount so I used a hair dryer and a pair of lineman's pliers to gently unscrew the lens mount. When putting things back to together, just remember to mount the rubber gasket on the front cover first before snapping it back in place.
@rickymedina7563
4 жыл бұрын
So just out of curiosity, with the lens screwed all the way in would you say it's focused on the foreground or the background? And about how far down is it screwed in from the factory?
@nicgibbens662
2 жыл бұрын
This is such a brilliant solution to my exact issue using a WyzeCam V2 in my enclosure- thank you so much for this!
@suivzmoi
2 жыл бұрын
2:45 just my input here but it is not a direct access to the sensor when you remove the lens assembly. there is a wafer thin piece of glass covering the sensor at that point. i know because that piece tends to fog over time with oils (long story,known issue, see forums) and i have had to remove it for cleaning on all my Wyze cams..
@jimmyjames1031
4 жыл бұрын
Will this help with closer then or farther then standard? I'd like to have something of a zoom like effect to keep an eye on my son's car down the street.
@graywoulf
3 жыл бұрын
You sure made this look easy. Thanks for the easy to follow directiona! 👍
@JasonTurcotte
3 жыл бұрын
The internal design of the latest Wyze cam has changed a bit with a larger rubber grommet. Also, there is a cap that screws onto the lens that comes off (was glued) and the lens is also glued into the unit. Used a small metal pick to remove the glue around the base of the lens and then it screwed out by hand.
@leighann5308
3 жыл бұрын
Where can I buy one of the focus ring? What is the min focus distance without doing anything without being blurry 2ft maybe?
@coffeeaddictgaming2883
Ай бұрын
Will this work for the new wyzecam V3?
3 жыл бұрын
Cool! What is the shortest distance you can focus on with this method?
@nihonsuki
2 жыл бұрын
When I was adjusting mine, it only took a very small turn (less than 1/8) to bring objects a few inches away into sharp focus, so I would guess it could focus very close with the lens screwed all the way out.
@dosdont
Жыл бұрын
It worked, thanks, hopefully it's just as easy with the V3's also
@thescinema
2 жыл бұрын
Thanks for the presentation and the file! Printed mine out, but I think I heated it a little too much because it wouldn't grab the ring. All good, though! Once I got it to grab a little bit, I set my focus, pulled the focus ring part off, put the rubber seal and cover back in place, and now it just looks like a Wyze Cam again :) Bonus, there's a little notch in the original ring, so if I ever need to make a quick adjustment, tiny flat head screwdriver for the win :D
@light-master
3 жыл бұрын
The cap came off the lens on me, and I tried to put it back together. Now it's stuck with a focus range of 4 in and less. Actually focused on since writing with the text basically touching the screen. Anyone know how to fix this?
@jayphilbin2871
4 жыл бұрын
Great idea! Went ahead and printed up the ring. I found that the lens had virtually no glue holding it. After going through the process I didn't like the vignetting created by the ring around the lens. I ended up pulling the ring off and with the face plate off, mounted the camera and turned the lens barrel to obtain focus. Afterward I replaced both the rubber gasket and the face plate allowing the camera its full field of view with perfect focus to boot.
@CannabisTechLife
3 жыл бұрын
Yeah this is what I ended up doing as well since I don't have a 3D printer and it worked beautifully!
@ideaxtruder
3 жыл бұрын
Hey Don, Great job. Have you thought about selling these on Etsy or something. I have had a few people reach out to me to print them. I have done it a couple times but in general I don't like selling other peoples designs. Also my own designs keep me busy enough.
@UrbanBirdsCLT
3 жыл бұрын
Thank you! This is exactly what I was looking for. Do you know if this would work for the new Wyze Cam v3?
@isaiahsdad
3 жыл бұрын
I have no idea, I am still waiting to get one to try it out.
@mattneidert
3 жыл бұрын
Just wanted to comment and say that you can do this with the Wyze Cam v3. I picked a couple up over the weekend. The procedure is a bit more invasive on the newer model, but it’s not too bad. I will say that there was quite a bit of glue, but I was able to pick it away and it will twist freely now.
@kyleeaton1709
2 жыл бұрын
@@mattneidert Did you use his Thing file to print the focus ring? I want to do this with my V3
@mattneidert
2 жыл бұрын
@@kyleeaton1709 I didn’t. Unless you need to constantly adjust it once modified and put back together, you can simply twist it with your fingers and then reassemble.
@dosdont
Жыл бұрын
@@mattneidert Can you elaborate a little with the V3? Did you just pop out the front, twist the lens and remove glue, then replace the lens and front? Or do you have to remove screws and take apart like other videos show?
@BartThomasTech
3 жыл бұрын
Can you share the 3D print file/info?
@isaiahsdad
3 жыл бұрын
www.thingiverse.com/thing:4322148
@jerrygrenoble
3 жыл бұрын
Anyone ever have an issue with the camera reading a qr code after? I couldn't get my camera to reconnect so I hard rebooted it. Going through setup now it won't read the qr code to set it up. Any advice out there?
@JulioPlasencia
3 жыл бұрын
This is genius! Thanks for sharing.
@ct810
8 ай бұрын
Doing this tomorrow! Thanks!!
@brucebutkus1251
4 жыл бұрын
went through the front eh, probably a lot easier than my method for replacing the lens.
@Hchris101
2 жыл бұрын
Is that from wall-e?
@Valrog_RC_3D
2 жыл бұрын
Thanks very much! It works great!
@patrickrenschler
3 жыл бұрын
thanks for sharing!
@TerryThomas812
4 жыл бұрын
very cool, thanks
@grumpymissblysdroneadventu7224
4 жыл бұрын
I knew you were more than just a pretty face!😮😁👌
@Eat_More_Possum
4 жыл бұрын
Nice!
@traveltrailerlife
4 жыл бұрын
Nice....
@kenhuffman7247
3 жыл бұрын
Great work with no lag of boring i gota be a star bullshit!
Пікірлер: 38