Xs750 triple it a great sounding bike, i know i have one and a cafe racer too. 👍🏻
@FjordHunter
11 жыл бұрын
Yeah it's getting there. I'm getting the seat upholstered now, gonna pick it up tomorrow.
@leroyborrego3671
6 жыл бұрын
FjordHunter where did u get that seat, looks good
@RTLEE1
11 жыл бұрын
nice and thank you for the help !!!
@Mars_tial
6 жыл бұрын
Hi man, I contacted some time ago about fairing, now I would have another question for you if you don't mind. I see you are running pod filters, I'm trying to fit them on my bike and lately I've been having a trouble with rpm not coming down, I'm suspecting lean mixture. Can you tell me if you've had to change the main jets/change needle level, or something else when you've done it ? Regards
@FjordHunter
6 жыл бұрын
Yes I went up 1 or 2 sizes on the main jets. You need to have pods without that inner lip that covers the air passages in the carbs. All cheap pods have that so you need K&N or the ones from Mikes XS.
@Mars_tial
6 жыл бұрын
Hi there, I was wondering if you remembered the tuning you had to realize on the carbs when installing these POD filters ? I'm about to do it and there is a lot of conflicting information on the internet, some say it's just a matter of raising the needle, some say it's about increasing the size of the main jets, some say it can't be done, etc etc. It's complicated to discern the good from the bad so if you have any informations I'd be very thankful Regards
@FjordHunter
6 жыл бұрын
I have Mk1 carbs and I used 147,5 main jets which are 1 size larger than original. The needles are in the middle position. Make sure you buy pods that don't have the internal lip that blocks the air jets, most chaep pods have that and I would never use them on vacuum carbs. I use the ones from Mikes XS that are designed like K&N pods.
@Mars_tial
6 жыл бұрын
Perfect thanks :), it's nice to find somebody who is in the same situation, I assume yours is also a 2D like mine if you're equipped with MK1 and 3-in-2 exhaust. There is a good chance I come back to you soon if you don't mind ;) Thanks again !
@FjordHunter
6 жыл бұрын
You're welcome! Yes mine is a 2D also. If you have more questions I'm happy to answer them.
@Mars_tial
6 жыл бұрын
Hi, Could you tell me where you found the rear fairing you used ? I can't find original fairing like this one, probably not looking it the right places Regards
@FjordHunter
6 жыл бұрын
I found it on a Dutch site called Ruig's Polyester. It's for a Ducati.
@exia00z57
8 жыл бұрын
I just got this as my 1st bike... still has some work to do but is there any tips you can give me when riding this bike??
@FjordHunter
8 жыл бұрын
Swap the petcocks and do the 2nd gear fix. Read a lot on the dedicated forums.
@PlisPlassuply
8 жыл бұрын
l m looking for ignitor test triple, can you help me.
@TheDeichboxxer
9 жыл бұрын
How tall are you?
@FjordHunter
9 жыл бұрын
I'm 182 cm. I have fitted rearsets now so the riding position is much better than in this video.
@balmoralpjk
7 жыл бұрын
😡😡😡😡😡😡😡
@SaddamPoopStain
9 жыл бұрын
How card rom the end did you cut it?
@FjordHunter
9 жыл бұрын
I don't really remember but roughly 10 cm maybe. Just enough to cut away all the rust.
Пікірлер: 24