I just got an XT600 less than a week ago, this video is a fantastic reference
@jh-tech5546
2 жыл бұрын
Thanks for your comment.
@amidointhisright
Жыл бұрын
@@jh-tech5546 I finally worked up the courage to tear apart my engine and replace the sheared drive shaft the previous owner welded and left for me to figure out. I used your video a LOT leading up to this moment and it really helped push me over the edge to undertake the engine rebuild. Thank you again for documenting your teardown.
@genefogarty5395
4 ай бұрын
@@amidointhisright Are you in the U.S.? I can't find quality parts anywhere here, suggestions?
@voxxxapiter4564
24 күн бұрын
Хороший справочник по разборке,Но разобрать и я могу,а вот правильно собрать не каждый сможет☝️
@zambocinquantadue6911
Жыл бұрын
Io ammiro chi fa questo lavoro e mi chiedo come si fa a non dimenticare di rimontare un rasamento o una rondella o una coppiglia o una guarnizione o un O ring. Siete dei fenomeni 👍💪🇮🇹
@TheodoreAndor
Жыл бұрын
You definitely know what you are doing! I can see you have lots of experience for sure. Wow good video Thanks
@jh-tech5546
11 ай бұрын
Thank you!
@MrDillemille
Жыл бұрын
Great video! So many parts and details that I get scared to do this alone!
@jh-tech5546
11 ай бұрын
Thanks!
@gongusdeedeetow1510
6 ай бұрын
Hey so does the top part where the valves go. Does that just not have a gasket? I’ll be tearing mine out to change valve seals and can find a gasket. Is it okay that way? Would liquid gasket work?
@jh-tech5546
6 ай бұрын
Yes, there is no gasket but you need to apply some liquid gasket (suitable for engines) to the gasket surface.
@bartconnors7695
4 ай бұрын
Great video! I have a 1984 XT600 that I love, but it has almost 50,000 miles on it now and is beginning to leak oil from what looks like the head gasket. Is it possible to replace the top end gaskets without removing the engine? Thanks!
@jh-tech5546
4 ай бұрын
Thanks for the comment. I did not have the engine in the frame but what I can see from this video it is possible: kzitem.info/news/bejne/k51jznuBbn1oepw
@sergiotish
Жыл бұрын
Gracias por el video
@stantrading4859
7 ай бұрын
Do you have a motor like this for sale?
@jh-tech5546
7 ай бұрын
No unfortunately not.
@Puntism
2 жыл бұрын
Fantastic video, thank you! If you reassemble please, consider doing a video on that too.
@jh-tech5546
2 жыл бұрын
Thank you! I disassembled his engine o get some internal parts to rebuild another engine. I is on the planning to film it when I assemble it but it will take some time.
@anasimonaityte4107
2 жыл бұрын
Thank you from Spain 🤝🤝🤝
@Lairy67
Жыл бұрын
Great video, I’m having to strip my engine down as the gearbox is knackered would I have to strip it totally or could it be done by leaving the left hand side of the engine intact ? Thanks.
@jh-tech5546
Жыл бұрын
You mean by leaving the flywheel on the crank and even maybe the cover on the case? That might be possible. I don't think there are bolts behind that hold the cases together.
@Lairy67
Жыл бұрын
@@jh-tech5546 thanks, gonna be one hell of a job !
@richardknott5846
4 ай бұрын
Please talk.
@francescosalvioli
Жыл бұрын
Hi JH-TEch, compliments, very nice and clean job! where are you located?
@Anonymous-Anonymo
5 ай бұрын
Hola amigo me gustaría comprar uno de esos, de donde se compra amigo usado
@sagevaldez5743
10 ай бұрын
Would it be possible to change the gasket on the side of the engine without taking the engine out of the frame? I’m new to fixing bikes and some guidance would be very much appreciated
@jh-tech5546
10 ай бұрын
I guess you mean to remove the clutch cover. Yes I think that is possible.
@traumhausparaguay5734
9 ай бұрын
Espero que pueda volver a juntarlos
@colefrench5896
Жыл бұрын
Just wondering what tool did you use to pull the flywheel? It looks like a harmonic balancer puller but my bolts are too short to thread into the flywheel all the way
@jh-tech5546
11 ай бұрын
Sorry for the late reply. As you could see I did struggle. The tool that did the job was the flywheel puller sold by YAMBITS.
Пікірлер: 35