I've been trying to decide if I should upgrade my 10 watt to either 20 or 30. This doesn't totally answer the question I was looking for but it does help me a lot. Thanks for the video, it is very helpful despite only partially answering my question (no your fault, it's not what the video was about). Anyway, take care and thanks for the vid :D
@ProjectAnonymous_Duo
5 ай бұрын
Thanks for watching!
@humbleacres5106
9 ай бұрын
Great comparison video! You have helped me to decide what laser I'm getting. Thanks again!
@ProjectAnonymous_Duo
9 ай бұрын
Glad we could help! Thanks for watching!
@Optikification
5 ай бұрын
I have an elegoo phecda 10w and thinking of upgrading the head and psu to 20w. Was looking for a comparison video to show if its worth it. Thanks for this info.
@ProjectAnonymous_Duo
5 ай бұрын
We are glad you found it helpful, thanks for watching!
@bigmd1343
7 ай бұрын
I don’t understand what the thought process was when they designed the connector for the laser module. I change my module often because I also have the IR module. They don’t last long and I can either rewire or change the whole wire harness. So many really well thought out designs with the D1. But some I really wonder what they were thinking.
@ProjectAnonymous_Duo
7 ай бұрын
We agree it is not easy to reach the connector. We aren't sure about the longevity yet, but we definitely have to be very careful with it. We have liked the set up so far, but there is always room for improvements. Thanks for watching.
@patatebanine4278
9 ай бұрын
Hi, is it easy for you to switch the 10w for a 20w on the machine?
@ProjectAnonymous_Duo
8 ай бұрын
Yes, we found it very easy to switch...one plug, one thumbscrew, and changing the power brick. Thanks for watching!
@ssteffe2
4 ай бұрын
I think will help in my decision.. thanks
@ProjectAnonymous_Duo
4 ай бұрын
Awesome, thanks for watching!
@katranitsa
9 ай бұрын
if you change the laser and the power adaptor is the same what will be happen?
@ProjectAnonymous_Duo
9 ай бұрын
We haven’t tried that, to be honest, but, I don’t think it would be catastrophic, maybe some loss of power?
@robertballesteros1187
8 ай бұрын
hi, have you attempted to cut through metal with the 20w? will it cut through metal? i'd like to see a video of that with the results. thanks! 😎
@ProjectAnonymous_Duo
8 ай бұрын
We have not attempted to cut through metal with the 20w. We will have to do a bit of research on that. We'd imagine if it is at all possible it would have to be extremely thin metal and very low thermal conductivity. As we understand it, a fiber laser is the best for use with metals. We did use our fiber laser in a video we just posted to cut through anodized aluminum if you are interested in checking that out: kzitem.info/news/bejne/lq2vyJiAcHyJoJw Thanks for the suggestion and for watching!
@rusticbear-bp9ii
8 ай бұрын
how can i speed up engraving borders. they take far longer than the actual middle bit im doing. today one piece took 90 minutes the border took 65 minutes of the 90
@ProjectAnonymous_Duo
8 ай бұрын
The only thing we could suggest is if you haven't already tried, is to create separate layers for those parts, then you can adjust the speed and power. Thanks for watching!
@the_edge_of_time
9 ай бұрын
Have either of you tried something that would use both 10w and 20w?
@ProjectAnonymous_Duo
9 ай бұрын
We like the 10w for engraving and the 20w for cutting, but we haven't swapped them out for one project yet.
@QuiltersHandyman
4 ай бұрын
Unboxing a total waste of time....there are dozens and dozens of these types of videos. Get to the use of the machine
Пікірлер: 21