50% speed, 60% power on black for anyone fresh asking, I get varying results with different colours sometimes so be mind full, I cooked a white one once at 100% power so if you are going a steak house “branded” look it’s actually pretty cool!!!
@DanMurtagh-e6s
6 ай бұрын
Thank you
@mojav3dlab739
Жыл бұрын
Awesome, Chris! Thanks for a quality video once again!
@brentjohnson6654
Жыл бұрын
Loved the video. Might have to look into getting that etcher or laser.
@SisterGraphics
Жыл бұрын
Amazing work and great video THANK YOU
@Xan-zh5ni
8 ай бұрын
Hi great informative video. I have a question if you could help ... I've seen ppl use the galvanised spray using stainless steel preset setting for glass. What settings would I use if I used tempara paint instead of galvanised on a glass? Would I have to go less aggressive on the settings? Cheers 😊
@SerendipitySue
8 ай бұрын
I've used the same setting for CarMark Black laser marking spray and for black tempura paint applied with an airbrush
@djslycaltwooneproductions1390
Жыл бұрын
What settings did you use for the steel tumbler? Thanks
@MegaMrcarbon
Жыл бұрын
What speed and power did you use for the glass?
@djfunkycraig
6 ай бұрын
Setting for second tumblers?? The magic question
@williamhbynumiii5269
8 ай бұрын
How did you do both sides of your tumbler?
@HiddenAffiliate
Жыл бұрын
What setting was used on the stainless steel tumbler
@Lisaamyshook
Жыл бұрын
I'm thinking about buying this laser for engraving glass candle holders for wedding comments for the guests to take
@Lisaamyshook
Жыл бұрын
How hard is it to learn? I'm pretty computer savvy. The software you mentioned does that come with the purchase?
@600miles
Жыл бұрын
1:25 74.5mm is same size as my Honda 600 car pistons.
@tonecrazy88
Жыл бұрын
Given the choice would you get the stool 20w like you have, the 40w or the 10w?
@SerendipitySue
Жыл бұрын
probably the 40W
@tsltc
Жыл бұрын
What speed and power did you use for the the black painted tumbler
@SerendipitySue
Жыл бұрын
Speed 50, power 60%
@DonaldBachman-ls8rk
9 ай бұрын
Can a IPad also work With the lazer
@noahsark5279
3 ай бұрын
I use my iPad via Blue Tooth BUT sometimes it stops in the middle and shows a disconnect message even though it’s not disconnected. Grrr. Not all the time but sometimes. I’m using the free Xtool software Creative Space. If someone has a fix for this, on my iPad, please speak up.
@robertrodriguez1074
Жыл бұрын
What are your power settings
@SerendipitySue
Жыл бұрын
for the black tumbler I used 50mm/sec at 60% power on my 20W blue laser
@djfunkycraig
6 ай бұрын
It’s funny I saw about mid way on the cooler was mint so kinda guessed it was around the half speed half power range, thanks for a great video!!
@patrickmckowen2999
Жыл бұрын
Cool👍
@rudolfkoch6431
2 ай бұрын
thank you very much , greetings from Austria
@rusty359359
10 ай бұрын
Very informative video, appreciate the time you took to make. Very handy video as I'm just getting into this.
@chelsasdad
Жыл бұрын
With the given power settings, how long should it take to etch glass?
@dawnsmith765
Жыл бұрын
What program are you using? l like the grid
@larrycolson7451
Жыл бұрын
Great informative video. Can you tell me the Speed and Power settings you used for the black tumblers?
@SerendipitySue
Жыл бұрын
I used 50mm/sec at 60% power on my 20W blue laser
@larrycolson7451
Жыл бұрын
@@SerendipitySue Thank you sir!
@cliffordjohnston2106
Жыл бұрын
Watched, but no settings given for stainless steel tumbler. Can you supply them? Thanks.
@SerendipitySue
Жыл бұрын
I used black laser marking spray and 50mm/sec and 60% power
@yuliyayat4004
Жыл бұрын
@@SerendipitySue thx, what about glass settings? I added too much and my glass shattered (((
@brianpierrotti453
Жыл бұрын
@@SerendipitySue so, you sprayed the stainless tumbler the same way you sprayed the glass. Maybe that is what I am doing wrong. My etching never comes out shiny like even after the washing.
Пікірлер: 36