Tip to save a little time: Linkages to the trim and reverse gate have quick release ends so no need to unscrew the fittings on the pump unit. Just slide the sleeves back and pull the cables off the ball fittings. You still have to unscrew the steering linkage though.
@Pwcmuscle
6 жыл бұрын
Great point
@deacadeind
3 жыл бұрын
Great video and thank you for taking the time🤘🤘🤘🍺🍺
@liftedf-150ford8
5 жыл бұрын
Excellent video! Very detailed.
@Pwcmuscle
7 жыл бұрын
Link for the full build here: www.pwcextreme.com/t/yamaha-gp1800-build-series-by-pwcmuscle-com/296
@FabazMr
2 жыл бұрын
Thank you very much by fab by fab in the French West Indies
@salvatorem740
27 күн бұрын
What sealant should I use
@fresh3131
7 жыл бұрын
Nice video, Thanks for the update. can you tell me what was the speed after install ?
@Pwcmuscle
7 жыл бұрын
Thank you! Results will be posted tomorrow on the full build page, but its upper 70s. This impeller is a bit tall for the setup; we are going to continue adding mods to increase power where it'll be better suited for future updates. Here is the link to the full build page: www.pwcextreme.com/t/yamaha-gp1800-build-series-by-pwcmuscle-com/296
@tonypinneri2274
4 жыл бұрын
1 3/8" in incorrect. it is a 36mm open end. don't buy wrench you don't need like I did.. just an FYI
@jeffr1085
2 жыл бұрын
Thanks mate appreciate the video
@christopherlow5320
Жыл бұрын
Thanks for the video..
@KMURRAY1841
4 жыл бұрын
Nice job pal much appreciated and awesome videos Joe! I can’t seem to pry off the housing any suggestion? Heat gun?
@HH-mq9of
4 жыл бұрын
Same problem How did you get it loose
@scottkarwowski1144
3 жыл бұрын
What type of sealant are you using or recommend when putting the pump back together?
@danielzentz8163
3 жыл бұрын
Was wonder the same thing
@fhaskell12
3 жыл бұрын
Did you find out? I need to know too
@senditsillly1423
5 жыл бұрын
Is that prop give better top end than the dual prop. I have stage 2. Also I’m at 138hrs and my clutch is still good, when can I expect to have to replace it? 200hrs?
@djjunior809
4 жыл бұрын
Thanks you the video Joe! Question though, how can torque the Solas impeller when installing it?
@Pwcmuscle
2 жыл бұрын
Tighten to hand. These are reverse threaded.
@jpassarella73
7 жыл бұрын
Is there any reason why you removed the ball joints from the trim and reverse bucket as opposed to simply removing the spring loaded socket cable ends?
@Pwcmuscle
7 жыл бұрын
Good point.....just force of habit really; the springs have given me trouble in older skis over the years.
@kirkm6736
6 жыл бұрын
Joe.....what type of adhesive should be used? Any chance you can name a brand or link to a product? Thanks.
@tirekicker99887
5 жыл бұрын
Kirk M threebond 1207b is what’s recommended in the factory Yamaha repair manual
@peterodriguez3053
5 жыл бұрын
I have a 2019 fx svho but I see the manifold is like plastic, can I do the same
@dproulx7380
3 жыл бұрын
Joe great video will marine silicone be ok for the pump sealant and with stage 1 plus are titanium retainers needed and is the riva coolant upgrade needed I’m up in northeast water temps rarely get over 68 degrees
@SlayerHawkX
16 күн бұрын
Little late here , but no need for retainers/intercooler on stage 1 plus ...I just done a full stage 2..getn retainers tomorrow..yahoo
@senditsillly1423
4 жыл бұрын
Hey joe what do recommend the lucky 13 pump cone or the Worx pump cone? Thanks.
@TheYeti308
Жыл бұрын
Hey Joe ; What pump moves the most GPM .
@maxjones9139
4 жыл бұрын
Yeah breaking the seal to get the pump out is a major pain.
@Pwcmuscle
4 жыл бұрын
For sure. Just wait until you have to break loose the impeller for the first time!
@lukereed1380
3 жыл бұрын
I feel like I’m going to shear the shaft with the amount of force I’m putting on the impeller. There is a lot of torsion/twist in the shaft. I’ve tried heating with a butane torch. Will it eventually release?
@maxjones9139
3 жыл бұрын
@@lukereed1380 If you have a good bench with a good vice on it it’ll come lose. I used a 6 foot metal fence post as an extension/negotiator. There was a pucker moment thinking surly I’ll f up the shaft but it came off. I got it good n hot too. Ordered a 13/20 from skat trak and the first one showed up with some imperfections. Make sure you give a good look at what you’re installing!
@djhamidreza
3 жыл бұрын
What’s the difference between dual solas impeller vs this one?
@Pwcmuscle
3 жыл бұрын
If you have the power to run the dual, it really helps with cavitation
@raymondbushey3898
3 жыл бұрын
how did ur solas last
@Pwcmuscle
3 жыл бұрын
No issues
@videntemusic2465
2 жыл бұрын
Hi bro I have questions I have waverunner ex sport 2020 I want to change the impela solas I need change the wear ring or not is obligated?
@Pwcmuscle
2 жыл бұрын
Nope, you do not need to change the wear ring out as well. You can do jsut the impeller. Here is a link: www.pwcmuscle.com/solas-yamaha-concord-144mm-12-20-impeller.html
@videntemusic2465
2 жыл бұрын
@@Pwcmuscle thanks
@videntemusic2465
2 жыл бұрын
@@Pwcmuscle my friend for waverunner vx 2022 what inpela I need for buy in you web to
@evostigti
3 жыл бұрын
Can I run a solas 13/18 prop on my ski with only an exhaust, waterbox and intake ? Will it be better than the stock prop ? Thanks in advance 🙏🏻
@Pwcmuscle
3 жыл бұрын
You can, but you'll be banging into the rev limiter on the top end.
@evostigti
3 жыл бұрын
@@Pwcmuscle I have a solas 13/18 I got from a buddy who sold his ski. Is it better to stay with stock impeller or switch to 13/18 ? Im a fan of acceleration not mostly a top speed guy
@Pwcmuscle
3 жыл бұрын
@@evostigti Test them both out. That 13/18 should give you superior acceleration, but again, you'll be down a couple MPH on the top end.
@evostigti
3 жыл бұрын
@@Pwcmuscle thanks bro currently trying to swap the pump out having trouble to pull out the pump after removing all 6 bolts. Any idea how to pull it out ?
@whittakersexpress8810
2 жыл бұрын
@@Pwcmuscle would you say 13/20 will work good on a 2020 fx for top speed
@eostrow1963
2 жыл бұрын
What’s the torque?
@jameskrivitsky9715
6 жыл бұрын
I saw on another video a tech saying the cap on the impeller slows the performance. He suggested leaving it off. Any input from you as far as results ? Thanks J K
@maxjones9139
4 жыл бұрын
I heard that also. I’m curious too.
@cadesaalmann49
7 жыл бұрын
Hey I would like to get into racing but don't know where to look online can u help?
@Pwcmuscle
7 жыл бұрын
Hi Cade, depends on where you are located. Shoot me a message on PWCExtreme.com and I can send you some specific links. -Joe
@cadesaalmann49
7 жыл бұрын
PWC Muscle ok thx
@BiLoSellHigh
2 жыл бұрын
Stock or the 13/18 Solas ?
@Pwcmuscle
2 жыл бұрын
I don't understand the question?
@marty906
Жыл бұрын
4:36 Looks like a 13/20
@k.tanaka1866
3 жыл бұрын
Got the impeller installed but I noticed there is A LOT of water in the GP after running it for just 10 minutes! Any idea what went wrong? kzitem.info/news/bejne/z6ehqI54h6iqn4o
Пікірлер: 59