This is a great video on the oil change i have followed your lead an implemented the hose an barb idea , i would have left it draining and changed the filter while it was still in the lowered position ,ive seen a lot of videos on doing this but one thing i have always done with cars bikes is remove the filler cap and also the dipstick .
@blainerichardson
Жыл бұрын
Great video! Thanks. I would like to have seen a part on what to do if the trim fluid is low.
@tommyliu4683
2 жыл бұрын
Best Video on this topic on youtube!! Thanks for making it!
@diginterpretations
3 жыл бұрын
Excellent video, thanks. The barbed drain hose trick is great, as well as the sequence you go through with the gear case oil change. I've been maintaining my F50 TLR for five seasons now, and I can definitely say those tips will help me this fall. I would also add a step to check the lower unit holding pressure (after draining it) using a small bicycle pump. There's a spec for that in the service manual.
@blahha1036
2 жыл бұрын
Im gonna go ahead and say great video. ta
@mackdenn
Жыл бұрын
Great video but when I tried to fill the gear oil in the lower unit with the same oil and pump and system you have, it stopped pumping at about 75% of the quart without spilling out of the top hole. Now what do I do? I'm finding trouble determining the gear oil capacity to know if there is enough oil in it.
@atmm89
2 жыл бұрын
very well explained, thank you
@jamespooley7844
2 жыл бұрын
Great video! Thanks, I picked up a couple good tips. Especially about trimming all the way up before draining the oil. I see you have a stainless prop. What is the pitch and model number of the prop? Thanks again.
@ronaldbertin9455
2 жыл бұрын
Good video ty
@brianlowe753
2 жыл бұрын
What is clear (pink) tube on starboard side of motor lying inside motor maybe lying in exhaust manifold?
@Bottomfeederonfire
Жыл бұрын
I’ve been changing the spark plugs with my 100 hour service, is that not necessary?
@muammer50
4 жыл бұрын
Thank u gör information
@lasse4416
4 жыл бұрын
Is there a difference between F50TLR and F50AETL ?
@fmaalouf73
2 жыл бұрын
Anyone know what size and pitch the house barb that was used?
@bobn7525
3 жыл бұрын
Are there two fuel filters plus the separator on the yamaha or one fuel filter plus the separator?
@jordanking905
4 жыл бұрын
Gear case oil looked very milky . You have to replace the seals?
@matthewb6086
3 жыл бұрын
The yamalube looks like that. It’s not green like the quicksilver sae90
@roygilliam8370
3 жыл бұрын
How to set mixture screws on 50 horse 4 stroke boat motor the year is a 99
@jordanking905
4 жыл бұрын
I don’t see an oil filter for my 03 tlrb. Is that a thing?
@Gregg0112
Жыл бұрын
Its an impact driver not an impact hammer
@omieyouknowme
4 жыл бұрын
Don't forget to add some oil inside filter and on seal, prevent dry start.
@damodoesall6240
5 жыл бұрын
What thread size is the barb oil drain fitting?
@matthewb6086
3 жыл бұрын
Did you ever find out? I assumed it was a hose fitting like for an air gun.
@damodoesall6240
3 жыл бұрын
@@matthewb6086 NOpe
@ohdeergod
4 жыл бұрын
that gear case oil was very milky.
@matthewb6086
3 жыл бұрын
That’s how the yamalube looks. It’s not green like the quicksilver sae90
@rossevans1774
4 ай бұрын
This guy should just 'go ahead' and do the job with a little less talking.
Пікірлер: 27