Excllent video thank you , just regarding the tourqe sensor volatage mine is staying at 0.5 volts. Is there a easy remidy for this or will a new tourqe sensor be required ? Thank you again
@altacyclinggroup2122
4 ай бұрын
If you turn on the bike and let it sit for 5 mins this resets the toque sensor. If this does not work we suggest your reach out to Yamaha for more information.
@XXsakurafan
Ай бұрын
I got error code e4 I can't find what it is
@Ubaid163
2 ай бұрын
Dear sir great video but my problem isn’t discussed here. Recently my bike has stopped pedal assistance. Although the walk assist works. The range written on the meter is blinking. I don’t know what has happened to my bike. Please help.
@_abel_9133
2 ай бұрын
i have the same problem still dont know what is causing it
@Ubaid163
2 ай бұрын
My speed on the display is constant 0 and the assist isn’t working. Help please
@Glegg
Ай бұрын
Speed sensor or pick up magnet on rear wheel.
@martynwatson4929
Жыл бұрын
Great video, judging by the amount of comments i'd guess the yamaha is a usually very reliable system. However, I had an error 73 on my display but your list of errors only goes up to 62. Would you know what 73 is? I've cleared it by remaking and waterproofing my connections, but would like to know what you think. Thanks.
@saschakumant9056
Жыл бұрын
I have the same error...what was broken?
@martynwatson4929
Жыл бұрын
@@saschakumant9056 It's a misleading battery error caused by Water getting in and is sitting on one of the chips on the lower edge of the pcb board in the motor. Don't try to use the motor, take it apart and carefully dry it out.
@altacyclinggroup2122
Жыл бұрын
@@martynwatson4929 What bike make/model do you have? These codes were for the Haibike systems. Other bikes with Yamaha system might have new errors code.
@saschakumant9056
Жыл бұрын
@@martynwatson4929
@trevorshields7347
Жыл бұрын
I wish!
@vfragzie4710
7 ай бұрын
I’m a little late to the party but the information portion on my display (range, trip etc) keeps flashing and the assist doesn’t work, any tips?
@NRGNathsRelentlessGaming
7 ай бұрын
My bike is also having this problem 😔
@altacyclinggroup2122
7 ай бұрын
Manual s.tates it could be one of the following: 1.(Even if the wheel where the speed sensor is installed rotates, the value displayed on the speedometer section of the display unit does not change from “0”.) Try new speed sensor 2. (When the wheel where the speed sensor is installed rotates, the speed is displayed on the speedometer section of the display unit.) This is not a malfunction. It is in a state that the operation of the power assist system is normal. This state may occur depending on the pedaling strength and riding speed, but it returns to normal condition if it is confirmed that the system is normal. 3. (When charging while the battery is installed to the bicycle) This state may occur during the battery in ternal temperature is -20°C or less or 80°C or higher, but it returns to normal condition if battery internal temperature returns to the normal temperature range
@PaweMurawski
3 ай бұрын
hey did you find the solution? For me, "range" is flashing and there is no speed, just 0 all the time. Ofc motor doesn’t work…
@Ubaid163
2 ай бұрын
Did you get it fixed? I’m facing this issue
@Ubaid163
2 ай бұрын
@@NRGNathsRelentlessGaming did you get it fixed? I’m getting same issue
@dimitarg3172
8 ай бұрын
Hello friend, what means d4 19021? Regards
@altacyclinggroup2122
8 ай бұрын
This means your firmware version is 19021.
@altacyclinggroup2122
4 ай бұрын
D4 just gives you the firmware version your bike is currently running. In your case its 19021.
@anndora5308
4 ай бұрын
My side switch won’t turn off anyone know what to do?
@recoilcsgo
2 ай бұрын
having the same problem, did you find a solution?
@CDP1985
Ай бұрын
Does anyone know what error code 71 means?
@altacyclinggroup2122
Ай бұрын
Error 71: Can't not receive data from battery correctly. You would first want to replace the receptacles wires on the bike and if this does not fix the issue you might need a new battery.
@ganeradaimos3054
3 ай бұрын
What does error code 68 mean?
@Michael-vl9jy
3 ай бұрын
Would love to know that too. My bike says it as well and power dropps when it shows.
@mikkopirttimaki312
21 күн бұрын
Is there any more information about this code?
@kevind5744
12 күн бұрын
I got my bike yesterday (Yamaha Crosscore RC) and during the first ride my display and motor assist turned off every 5 to 10 seconds. After reseating the battery, I got error 68 after driving several kilometers without issues. And then after rebooting the display, it went back to shutting down every 5 to 10 seconds after another few kilometers. I would also like to know what's causing this.
@Michael-vl9jy
12 күн бұрын
I gotta say. I had it in de beginning. But after a couple of times of removing and inserting the battery again, the error is now gone and the bike is fine. So I assume it has something to do with bad connection of the battery.
Пікірлер: 39