I'm ordering a setup barkbusters tomorrow and Where did you get the blue levers from? I just bought a 22 icon blue t7
@marinoopen
4 жыл бұрын
Thanks for this effort. I will buy from you instead of local USA just because of this helpful vid and the useful comment on how to make them work with the OEM heated grips. What levers are those and do you have a vid on their install? Thanks
@ludoevens2585
4 жыл бұрын
Does the T700 have Corona too ? Because of the gloves for a handlebar ?
@comfortablyunknown700
4 жыл бұрын
I was hoping RR would pickup a T7. Very curious to hear your opinions. Hopefully someday I will be able to ride a T7 here in the States.
@JoeJ523
Жыл бұрын
I cut like a half inch off my t7 handle bars do you think that would make the bark busters not fit ?
@HORNET6
4 жыл бұрын
Good but you didn't mention the different length clamp screws
@JamesVarty
4 жыл бұрын
This was critical failure in my installation, the outer clamp screws are shorter
@agkikas
4 жыл бұрын
rally raid... what levers are you using?
@jackchristodoulou197
4 жыл бұрын
How do you take the standard bar end black weights off
@LongPondNH
Жыл бұрын
Thanks for the vid, but jeez that segment with the swirling camera was annoying. The part of the installation that it obscured is usually the tricky part.
@rallyraidproducts1927
Жыл бұрын
Yea it wasn't the best content back then I'll admit 😅 I'd like to thinks its improved since
@corecass
3 жыл бұрын
i see you have the same cable issue as i have. if you have your clutch and break leavers a bit lower as standard you get clearance issue's with the cable and brake line. i find this really anoying.
@magilla2567
3 жыл бұрын
I noticed not much interaction between RR and others seeking info while watching these vids. Must be very busy at HQ.
@rallyraidproducts1927
3 жыл бұрын
Yes being a very small team out time is dedicated to production mainly. We would love to have more time to continue with content. I try to make the content contain as much information as possible
@mortenkd9971
4 жыл бұрын
They do not fit together with heated grips.. :-(
@rallyraidproducts1927
4 жыл бұрын
With Oxford grips they do, we are using them together
@mortenkd9971
4 жыл бұрын
@@rallyraidproducts1927 Not the original Yamaha heated grips..
@dzordzanonymous1304
4 жыл бұрын
Are you sure? @RALLY RAID PRODUCTS would you confim?
@paolopalicalligaris
4 жыл бұрын
They fit with the OEM heated grips , but you have to use the original (Yamaha OEM) weights and the original screws at the end bars or , even better, some screws as the Barkbusters ones but 4 mm shorter.
@ParagliceCayenne
4 жыл бұрын
I installed the Barkbusters Tenere 700 Handguards on my T7 with gripheating. Positiv: - looking strong Negativ: - dont fit easily. Ireally needed to change stuff and be creative to get them installed. So if you arent a good DIY guys, i would not recommend them. (It looks as id they didnt have a T7 with gripheater to check the dimensions) For me never again products from barkbusters .
@jurgenhaneklaus8444
4 жыл бұрын
I just bought them and I have Yamahas heated grips. What did u change, could u pls explain what u did
Пікірлер: 21