Itu sama kerusakannya tidak ada tampilan cuman lampu power kecil yg msih menyala Info tukang servis servo pack yaskawa di indonesia😁
@liningarcher6629
Жыл бұрын
I have a Servopack SGDH-04AE that has no display showing. I’m going to try what you did in the video. What type of desolder flux did you use to remove the capacitor
@ryantechroom3369
Жыл бұрын
Soldering pump can also do the job
@aqilabariza6285
Жыл бұрын
Hi, I have an SGDS 08A12A servopack, with the problem of the display not appearing, I followed your procedure but when I tried it the display still didn't appear, do you think there is another cause?
@ryantechroom3369
Жыл бұрын
Most possible there are other issues. Try to check the fuse.
@geraibarra1391
10 ай бұрын
Tengo un servopack yaskawa sgdh-04ae qué trabaja por un corto periodo y luego se apaga por completo me podrías ayudar a corregir ese error
@cuongThan-mf3id
4 ай бұрын
Hello! I would like to ask about the servo driver SGDV 330A01A, I lost the display and when powering 200v 3p L1, L2, L3. Parallel connection of L1C, L2C driver servo is not displayed, but the LED is there.
@ryantechroom3369
4 ай бұрын
Try to check the similar capacitor just like on the video..possible same problem.
@dedesuhenda6034
9 күн бұрын
Hello, to servo driver SGDV 2R8A11B, problem same, what kapasitor the same ?
@pajarardianto8946
6 ай бұрын
I Also have same problem with you sir ,but I Use SGD7S-590AA0A ,what should I do sir ? I dont know where the IC power
@ryantechroom3369
6 ай бұрын
Sigma 7 and sigma 5 almost same circuit..
@TOTS05
10 ай бұрын
Hello ,I HAVE SGDM 30ADA SERVOpack ...what should i do with this kind of problem er A.C 9 . hope u can help me ..
@ryantechroom3369
10 ай бұрын
For AC9..try to replace encoder cable or reinsert it..
@adamskayode-fw9pf
Жыл бұрын
hello i have SGDV-5R5AO1A yaskawa, the charge indicator light is not coming ON, kindly advise on what to do.
@ryantechroom3369
Жыл бұрын
Try to check the fuse..
@rafaeltolentino7029
2 жыл бұрын
Hello dear friend, have you reviewed a yaskawa SGD7S-330A00A000F80 servopack? And do you know how I can feed it with direct current and at what voltage?
@ryantechroom3369
2 жыл бұрын
For this specification.. the voltage need for input side is 200V.. however for verification you can check in the sticker attached to it..
@jeremyortiz906
2 жыл бұрын
una pregunta, los capacitores grandes que microfaradio y voltaje son? los dos grandes verdes de la orilla
@ryantechroom3369
2 жыл бұрын
Capacitor 33uf 25V
@gilaya5628
2 жыл бұрын
Hello master. Please help me. I have yaskawa SGDH-75DE-OY no display after I replace the fan stock.
@ryantechroom3369
2 жыл бұрын
If there are no display or even LED indicator possible you have forget to connect some parts..or worst you have broke the unit. But if the LED indicator is lit please check the same parts that to be replace just like on the video.
@vantuti9634
6 ай бұрын
Hello, can I ask about the error - on the sm5 servo on the display?
@ryantechroom3369
6 ай бұрын
what error?
@andestasigit1145
7 ай бұрын
Gan saya punya sgdm04ada,masalahnya ketika ditest jog manual semua normal,namun ketika pakai mach3 tidak mau berfungsi.saya coba tukar board controlnya punya driver yg normal dan berfungsi normal.kira2 masalah pada komponen yg menerima pulse pada cn1,ada saran gak part apa yg harus saya ganti
@ryantechroom3369
7 ай бұрын
It will be difficult to replaced those ..i suggest to replace only the control board if you have one.. or try to replace the electrolytic capacitors on it.. in Sigma V there are 100uf 6v and 33uf 25v..
@andestasigit1145
7 ай бұрын
Ok, thank's for your aswer. Can i to call or private masage or wa number?
@electronicsautomation7785
2 жыл бұрын
SGD7S-7R6A00A SERVO DRIVER NO DISPLAY I HAVE CHECK THE FAN VOLT IS 8 VOLT BUT FAN VOLTAGE IS 24 VOLT. ANY SOLUTION OF NO DISPLAY PROBLEM?
@ryantechroom3369
2 жыл бұрын
Try to check the power circuit just like on the video..
@electronicsautomation7785
2 жыл бұрын
@@ryantechroom3369 i have checked. any contact number on Whatsapp
@TOTS05
10 ай бұрын
Hello sir can u help me with my delta. Servo DEFAULT AL005. hOpe u can help me
@ryantechroom3369
10 ай бұрын
What servo type or servo model?
@TOTS05
10 ай бұрын
@@ryantechroom3369 hello its a servo drive
@wawanwibisono6010
2 жыл бұрын
Hi friends, I have a problem with the Yaskawa drive error 100, what should I check, I'm waiting for the solution, thank you in advance
@ryantechroom3369
2 жыл бұрын
What yaskawa model do you have?
@bichnguyen5059
2 жыл бұрын
Hi, i have 3 driver yasakwa sigma 3 no power. Replace capacitor to fix it. Is it right?
@ryantechroom3369
2 жыл бұрын
Yes, if only if the problem is same as on the video.
@bichnguyen5059
2 жыл бұрын
@@ryantechroom3369 i was try, it ‘s okey
@bichnguyen5059
2 жыл бұрын
Thanks
@fajardian7683
2 жыл бұрын
Hello sir, i replace capacitor, now display on, but error af6 on display, even though the servo-on is active, how to fix it sir?
@harshalirewale2664
2 жыл бұрын
How to identify display section ic...
@ryantechroom3369
2 жыл бұрын
Sorry, but I don’t which part is for display section. However, the display circuit usually separated in main board in yaskawa..
@abuhanifazadazad2142
2 жыл бұрын
How to repair AC servo alarm four
@ryantechroom3369
2 жыл бұрын
What type servo? Is it Sigma V or Sigma 3?
@tonygarcia9075
2 жыл бұрын
Hello friend, I have one model yaskawa Servo pack SGDH-o4AE, will it be that if I change this one, will it work?
@ryantechroom3369
2 жыл бұрын
Sorry but I don’t have experience on opening this type of servopack but we do have that type. And considering that they have the same manufacturer you can check if they have the same circuit or components.
@9_PANDA99
2 жыл бұрын
Hey sir I have yasakawa SGD7S-5R5A00A model with A-410 any suggestion to this
@ryantechroom3369
2 жыл бұрын
What is A410? Alarm at Servo Driver?
@9_PANDA99
2 жыл бұрын
It's alarm coming
@9_PANDA99
2 жыл бұрын
Main DC circuit is too low ( Under voltage
@ryantechroom3369
2 жыл бұрын
@@9_PANDA99 please check power supply voltage. Or if you some spare of same servopack or motor you can simulate. Or you can check PN509
@9_PANDA99
2 жыл бұрын
I got 5 units every unit is having same issue power board is ok I have swapped control cards what will you suggest I need to change any IC ?
@au10tic45
Жыл бұрын
how to wiring pulse and dir input I/O pin
@ryantechroom3369
Жыл бұрын
what type of yaskawa servomotor you have?
@au10tic45
Жыл бұрын
@@ryantechroom3369 i have same in video.sgds-04a12a.wiring use to breakoutboard mach3 step and pulse
@ryantechroom3369
Жыл бұрын
@@au10tic45 if you’re using mechatrolink this servo driver controls via software for dir and input
@au10tic45
Жыл бұрын
Can i use input i/o pinout?
@ryantechroom3369
Жыл бұрын
@@au10tic45 as long as you are using a non mechatrolink type servopack..
Пікірлер: 65