Driving GT3 and GT4 exclusively in ACC, being able to modulate the ABS engagement is an absolute GAME-CHANGER!! Already shaved over a second on most of my lap times. Get these...NOW!!!
@mcbogga
Жыл бұрын
How do you not have more views with these production values?
@simracingden
Жыл бұрын
Thanks that’s a really nice compliment! I’m still new in the game but having fun making videos, thanks for watching
@IDontTalkToCops
Жыл бұрын
@@simracingden It takes time but if you continue making videos like this your channel will do really well.
@luxie8097
Жыл бұрын
@@simracingden anything with a good mic and no generic dubstep intro music is a like from me.
@JoshuaHambyOfficial
Жыл бұрын
Seriously. A+ content
@wdodoo4707
4 ай бұрын
Parts of the script is basically identical to this video from two years ago. kzitem.info/news/bejne/xWmwqGSvqnaVfGUsi=cyXxtuwqtsgLW58C Still, decent video.
@ultimatehovado1
Жыл бұрын
This is really funny! Because I'm building these rumble sets myself! And my first design was "wrong" in the same way as these!! :-) You have to mount/build these motor mounts the way that the actual motor is vertically situated, that way you will have more precise vibration in lower RPMs because you don't have to take into consideration the weight of offset ballast, if you mout motor horizontally (like in this video) the weight itself will put "force" against motor and it will be harder to start spinning. V3 pedals had their motors mounted properly and in the right direction! ;-)
@ArianrhodTalon
Жыл бұрын
I have this for my T-LCM and play ACC. I loved driving the Porsches, but after update 1.8 they became undriveable to me. The back end will step out and I could never know when or why. I got the rumble kit, and gave the Porsches a try again. That’s when I realised from the feedback it was my throttle input. And it taught me to be more smooth on acceleration, or modulate the amount of throttle over long high speed corners. The sensation of knowing your rear is just about to step out, and you immediately respond by lifting the throttle a tiny bit and straighten the steering input slightly to catch the car. It’s awesome.
@chrismcdonald5775
Жыл бұрын
Lift-off oversteer. Porsches are especially prone due to the rear engine, RWD configuration.
@iracer9395
Жыл бұрын
I have these and ive set them to activate when ABS and TC kick in on GT3 cars. They are very helpful. Kit is well made.
@matthewbyrd398
Жыл бұрын
Exactly!!
@clutch44444
Жыл бұрын
This is great for getting the feel of wheel lockups and when the clutch pedal bites, this is the next step for sim racing
@simracingden
Жыл бұрын
Definitely!
@michaelpickford7298
Жыл бұрын
Been running these for over a year now with his wind sim kit as well and have had no issues and there both things I can't race without.
@simracingden
Жыл бұрын
Hoping to test a wind kit soon
@StevenYanni
9 ай бұрын
Interesting, I had Heusinkveld sprints, moved to SRP pedals now and waiting for SRP to come up with their own feedback system which I believe they are working on now. Glad to know there are a lot of Canadian sim racers. I'm from Toronto ON and been sim racing for over 8 years but I've been a fan of motorsports since I was 4 :)
@VishnuRajam4x4
Жыл бұрын
Have this for my TLCM pedals and they are absolutely fantastic! However the wait time is currently 4-5 months after ordering due to the chip shortage
@gigas27
Жыл бұрын
That sounds ridiculous. Search the forums man you can easily do this yourself for less than 50$ with some creativity.
@jonnovak
Жыл бұрын
I have the simagic p2000 pedals, 3 pedal set. dont use clutch so i ordered the 2 pedal kit 5 months ago. as i said, parts supply issues caused problems with lead times. got the kit and it had an extra motor included for some reason. only problem, it didnt include the wire to connect it to the control box. So i found an old laptop charger cord and the end worked to plug this 3rd motor into the box, with a bit of cutting and soldering, i now have this 3rd motor bolted to the bottom of my seat. :) To be 100% honest, this under seat motor just connects everything together. granted i havent had enough time to get settings all perfect, but i would have to recommend getting an extra motor or adding a seat motor kit with the pedal kit. 1000000000% worth the extra. Just takes the kit over the top !!!!
@exci6198
Жыл бұрын
There are small products called exciters (25-30$ each) that can take care of these effects without needing to mount a big shaker near the pedals. Great stuff nonetheless, thanks for the video!
@simracingden
Жыл бұрын
Thanks for the info!
@kevin_m
Жыл бұрын
Nice also have sprints. Gamer plus at rear. Dayton BST-1 under pedal tray at front. And a diy shaker on my brake. Using the nobsound mini amp for front shakers. Simhub is just amazing.
@simracingden
Жыл бұрын
Sounds great!
@TheOfficialOriginalChad
Жыл бұрын
The nobsound doesn’t provide enough power for the BST-1. This can cause clipping and believe it or not, damage tothe transducer. Upgrade to a real 100W amp and you’ll be happy, that is if the plastic that holds the mass in the transducer hasn’t already broken.
@kevin_m
Жыл бұрын
@@TheOfficialOriginalChad oh first I’ve heard thanks! Do you have a recommendation of an amp that would drive the two daytons I have up front now? I now have one on each corner up front.
@homevid
Жыл бұрын
I bought 3 motors (clutch ;) ) -since then, I wouldn't or couldn't drive without anymore..... simple comparison: if I'd remove your ffb from your wheel, would you enjoy it? Same here... new vibes into your pedals! I highly recommend it :)
@paulbuswell6566
Жыл бұрын
I've got simhub, motors with an arduino and motor shield (same as this kit, but cheaper to build at home) I have them on brake and acc, and love em. I've thought about putting one on the clutch pedal, but can't think what to map it with in simhub..I'd like to simulate the bite point on the clutch. What features are you mapping to your clutch pedal?
@homevid
Жыл бұрын
@@paulbuswell6566 Hi Paul... to be honest, I didn't test it yet, neither got any use of, as so far I barely use that pedal ^^ And the few times I drive the F40 with the shifter, I do not pay attention on the clutch rumble... I'd have to take some time and check out that point :) Sorry ;)
@v0ldy54
Жыл бұрын
Just got into sim racing, found a good deal on a pair of Fanatec CSL Elite and what definitely misses the mark the most is the clutch because you can't feel the bite point at all which is really evident in a real car, I immediatly thought that a small vibration could provide a more realistic feedback in that aspect.
@simracingden
Жыл бұрын
That's not a bad idea It might help but you'll need to confirm whether in simhub this can be configured based on the sim data would be curious to know if it's possible or not.
@v0ldy54
Жыл бұрын
@@simracingden as I said I'm really new to sim racing (so far racked up 80 hrs of Assetto Corsa with a gamepad, many of them spent trying to achieve photorealistic screenshots instead of driving :D) so I have no idea, however a quick search and I found this, seems doable to me kzitem.info/news/bejne/wKeJn4Wnp5V5h6g
@jonnovak
Жыл бұрын
Enjoy your videos. Ive been waiting for my set for months because of the supply issues the world is going thru. Finally my set is on the way
@simracingden
Жыл бұрын
Thanks for watching! It's worth the wait!, let me know your thoughts once you receive your kit.
@stephenarmstrong5263
Жыл бұрын
I should have mine for the TLCM pedals this weekend fingers crossed.
@simracingden
Жыл бұрын
@@stephenarmstrong5263 🤞
@Samoss13
Жыл бұрын
I have SIM3D also and it's a game changer tbh
@wostrick2259
Жыл бұрын
Another well presented video man! A happy subscriber 👍
@simracingden
Жыл бұрын
Thank you! And thanks for the sub!
@timwood8381
8 ай бұрын
Loved the video and the pic of the wired rig hahahaha bro I laughed so hard
@UTubeSL
Жыл бұрын
Great review! Thanks, and good luck with the channel.
@simracingden
Жыл бұрын
Thanks!
@RohitVerma-hf9ns
6 ай бұрын
Absolutely amazing!!!, Thanks👍
@simracingden
6 ай бұрын
Glad you liked it!
@Jajaja..
Жыл бұрын
Simply disassemble an old massage mat, remove the vibration motors and screw them to the pedals. Good, cheap and works great. When I see what all that stuff for sim racing costs, it's cheeky. With a little imagination, you can achieve exactly the same result for a fraction of the cost.
@simracingden
Жыл бұрын
If you have the time and know how a DIY is also always a great option!
@Azza-25
Жыл бұрын
I did the exact same thing back in 2011, cost me less than $50 and it worked really well. I used one of the sound activated massage mats, so I was able to run an audio splitter, ran that through an EQ to isolate the brake sounds, then the pedals would vibrate when the brakes locked up or there was tyre squeal etc. My build guide is probably floating around on the iRacing forums still. It worked well but I didn't like it, it felt like a gimmick and just didn't feel realistic at all. I later upgraded to a hydraulic brake pedal and removed the shakers and found this was a more realistic feeling pedal that made consistent braking easier.
@pmc40
Жыл бұрын
@@simracingden exactly, i'm no good at the technical stuff, can't wait for mine too arrive
@alexandershaw2378
Жыл бұрын
R.I.P @4:23 😅 The bane of our exis--taunce! "*said in French accent*"
@Simcadepro
Жыл бұрын
what will make your experience more joy-able is to use sim racing studios trust me it a true game changer
@davidpatterson6402
Жыл бұрын
srs is a great piece of software ....couldnt recommend it highly enough 🤟😜🤟
@andychicago8295
Жыл бұрын
I found them for my Heusikenveld Ultimates on the manufactor homeage :). I looked at the wrong site before. I ordered them yesterday. Now I need a power connection for Germany.
@simracingden
Жыл бұрын
Right on
@Chris_2709
10 ай бұрын
Hi! Thx for the video!! Csn you tell me, how loud these things are? Is it something for the bedroom 🤔? Thx!!
@simracingden
10 ай бұрын
They get kind of loud sometimes maybe not best near someone sleeping.
@Chris_2709
10 ай бұрын
@@simracingden ahh…ok. Mhh…then I must about that…shit 🤔☹️
@erikoddmundfostervoll2607
Жыл бұрын
Exellent video and review👍😊
@simracingden
Жыл бұрын
Thanks for watching!
@IDontTalkToCops
Жыл бұрын
Excellent review. Liked and subbed 👍
@simracingden
Жыл бұрын
Thank you!
@giogamer4825
Жыл бұрын
Really great, but as this is not possible on Ps5, I am happy with my Fanatec V3 for now. Really like the rumble motors, as I do feel them good with socks on
@simracingden
Жыл бұрын
The Fanatec V3 is a fantastic set for this reason.
@michaelkopec.5814
8 ай бұрын
great Video., very informative., What triple monitors are those ? Thank you.
@davidsobreiro3583
7 ай бұрын
Hey Mike, thanks for this review, one more sub! I just have a question I couldnt see anyone speaking about. How loud do you find this rumbles? I mean with headphones probably doesnt botter you, but if theres more people around could this be a problem, or can it be not as loud of you reduce its strenght on simhub? Cheers
@simracingden
7 ай бұрын
They do produce a bit of noise. It's noticeable for sure, not as much with headphones, but to those close by or around you, you will for sure hear it. It didn't matter too much, regardless of strength; it's just the noise they make when spinning. I hope this helps.
@arielcor7392
Жыл бұрын
If you have a seat with movement, it is not necessary. No fancy pedals needed either. If you have movement, the feeling of braking is given by the movement of the seat.
@SSmallwood
Жыл бұрын
6 axis seat platforms cost over 5k dollars though. even with a motion platform youd still want load cell or even hydraulic load cell brake pedal lol
@arielcor7392
Жыл бұрын
@@SSmallwoodI only have 2dof built by me and that is enough. I already have the feeling of how the car is braking. The difference between using the move and not using it is 90% of the simulation. Obviously a 6dof will be much better.
@fleetc
Жыл бұрын
Try one small 15-25watt transducer attached to the base of the pedals. It would do the same without the latency.
@TheOfficialOriginalChad
Жыл бұрын
This is simply not true. Transducers depend on the deflection of the item they’re mounted to, they have to shake them, hence the term “bass shaker”. Most pedal base plates are the MOST SOLID part of the sim rig. Additionally, if the pedals aren’t shaking then the bass shaker is, which is TERRIBLE for it and creates awful resonance and clipping. The mass on the end of these rumble motors is 5x heavier than that in a 50W transducer and it’s DIRECTLY attached to the pedal, not the pedal base plate. This is significantly more effective. How do I know? Well I’ve spent around 40 hours trying different transducers from 15W to 100W, amps, pedal mounting plates, flexible transducer mounts, oscillation isolators, etc and NOTHING came close to cheap rumble motors mounted to the pedals directly.
@geoffholden4655
Жыл бұрын
Good video I might try them. As a fellow Canadian welcome to the sim racing obsession. What part of Canada are you based might catch you online.
@simracingden
Жыл бұрын
Thanks! 🇨🇦🙌🏻Yes worth getting for sure let me know if you get them and what you think. I’m from Toronto area how about you?
@geoffholden4655
Жыл бұрын
@@simracingden I'm in the whitby area
@jack-uc3of
Жыл бұрын
Hi there. I just saw this review for the first time. Well done! I am looking to order these, but I was not able to find them on Etsy site. Do you know if the seller is still making them? Thank you
@simracingden
Жыл бұрын
Hey, thanks, he has his own website now here is the link -www.sim-3d.co.uk/product/pedal-rumble-motor-kit/6 Thanks for pointing this out I didn't realize they were no longer on Etsy so I'm updating the link now in the description
@steam-SMOKEY
Жыл бұрын
Appreciate the heads up. Subbed -1000th😁👍
@simracingden
Жыл бұрын
🙌🙌🙌
@OlderGamersPerspective
Жыл бұрын
These do look cool, but would they work, using SIM HUB and a NLR HF8? By that I mean, can SIM HUB output into two devices at the same time?
@simracingden
Жыл бұрын
Yes this is absolutely possible.
@sky173
Жыл бұрын
Great video. It's been over 3 months now. Are they used regularly? How are they holding up?
@simracingden
Жыл бұрын
Have used them regularly Working great same as day one no issues
@funanmusicdrums
Жыл бұрын
Hi man! great video and idea! does it work on moza pedals? do you ship to Brazil?
@simracingden
Жыл бұрын
Hi! Thanks for watching, I don’t see the Moza pedals listed as an option but it would best to contact the seller directly on Etsy to inquire about this. www.etsy.com/ca/listing/1060376767/
@matthewdickerman3142
8 ай бұрын
lol some CSLs with a load cell and these mods are better than expensive pedals with no mods.
@kennyrodg
Жыл бұрын
Have them on my Meca Cup 1's.....i wouldn't be without them..fantastic it of kit.
@simracingden
Жыл бұрын
Nice! How do you like meca cup pedals?
@kennyrodg
Жыл бұрын
@@simracingden Hi....I can't fault them to be honest...The build quality is fantastic...I've had them approx 18 months with no issues....I'm a happy camper, I'd have no problem recommending them to anyone thinking of upgrading.
@jwadzy
Жыл бұрын
How did you setup your pedal motor kit to just be front and the buttkicker in the rear? Is that all through simhub? I don't see any setting to choose front/rear in the buttkicker app.
@simracingden
Жыл бұрын
You can configure the output in the sim hub under the channel outputs menu. For example, you can select which effects and device handles front or rear.
@Cevap05
Жыл бұрын
Hey so I currently have the V3's and am looking to upgrade to better pedals. How would you say those rumble motors compare to these? Are they substantially stronger, even through shoes?
@simracingden
Жыл бұрын
I found these much stronger then the fanatec rumble motors and definitely feel it through shoes.
@trevorbelmont4633
Жыл бұрын
Do you have demo for how loud it is? What would be the difference with using a puck instead of the rumble motor?
@simracingden
Жыл бұрын
I will make a video short of the sound; it does produce some noise.
@savage5764
Жыл бұрын
Only negative of the kit is the sound the kit emits is asburd.
@Germannn
Жыл бұрын
if you have amotion system it work this pedals systems ?
@simracingden
Жыл бұрын
It shouldn’t be an issue as it has nothing to do with a motion system
@stevetb7777
Жыл бұрын
Wouldn't transducers or something ELSE mounted to the brake pedals make more sense than rumble motors? I would think transducers not simply being on or off would give you more flexibility. I've seen videos of folks doing that as a DIY before.
@simracingden
Жыл бұрын
Yes thats another great option but they can be harder to mount maybe or add weight, but not sure never tried it myself.
@shellymurphy97
Жыл бұрын
What are those stripes to seamlessly connect your monitors?
@simracingden
Жыл бұрын
Its the ASUS ROG Bezel Free Kit check out my review here - kzitem.info/news/bejne/rnmfyG2YqZaifZw
@ethandolny
Жыл бұрын
I have the Fanatec CSL Elite V2 Pedals, would you recommend?
@simracingden
Жыл бұрын
I would recommend these for any supported pedals
@FulLShoT
Жыл бұрын
Hello there! do you still run this settings?
@simracingden
Жыл бұрын
At the moment I’m not using these as I switched pedals and haven’t mounted the rumble motors yet but plan too.
@lightzz3
Жыл бұрын
do you think they'll be adding one for the logitech load cell
@simracingden
Жыл бұрын
Not sure would suggest reaching out to the seller maybe they can help
@Mrequine1
5 күн бұрын
i seen this works with grand turismo 7 but no explation how
@simracingden
5 күн бұрын
Would reach out here on this: discord.com/channels/789862550987866134/795533945345146890
@usernametakennnnn
Жыл бұрын
Hi! What's inside the control box? I'm curious if it is an arduino. Thanks!
@DarkPand0r
Жыл бұрын
It is indeed an Arduino.
@usernametakennnnn
Жыл бұрын
@@DarkPand0r Thank you
@simracingden
Жыл бұрын
Yes, it is
@konradmankowski1471
Жыл бұрын
Unfortunately, they do not fulfill their orders! I waited 14 weeks for my first order after sending many emails. On my second order, I gave up after 11 weeks! On their website it says that the waiting time is 6-8 weeks, which is not true (they mislead the consumer - all the time some excuses) now I'm waiting for a refund, we'll see how long it will take.
@simracingden
Жыл бұрын
Any updates on how this was resolved?
@Eskoxo
10 ай бұрын
simagic p1000 seem to have better solution as an add on... if only someone made a mod for them to be used on more pedals.
@simracingden
10 ай бұрын
That would be great. I'm sure someone is going to come up with a solution.
@Eskoxo
10 ай бұрын
@@simracingden was talking to race beyond matter he tested it said it works with p2000 box and suggested to simracing machines might make an adapter but will see.
@19spikerman
Жыл бұрын
How was the noise of this kit compared to a Buttkicker?
@simracingden
Жыл бұрын
It’s not very noticeable definitely quieter that the buttkicker will depend on your settings obviously but if you got headphones or speakers loud won’t hear it but someone in another room sleeping might be bothered a bit
@spiritchaser4337
Жыл бұрын
There it goes again, SimHub. Can’t use it with my motion simulator, it interferes with SimTools, no matter what port forwarding I do. UGHHH.
@TheOfficialOriginalChad
Жыл бұрын
6:30 “ABS is not as quick as braking well without ABS” This is completely false. It was once true for road cars, but it hasn’t been true for a long time. ABS isn’t outlawed in so many racing series because it’s slower…
@RobinHood-yk8og
10 ай бұрын
ABS is 'outlawed' because of expense and complexity. While ABS can provide better emergency stopping for most road drivers, it will not outperform manual brake modulation for an even remotely serious driver who's trying to achieve a quicker lap time
@TheOfficialOriginalChad
10 ай бұрын
@@RobinHood-yk8og like I said…completely false. I have been racing and instructing for over a decade and have HEARD this a thousand times, all from amateurs or spectators, NEVER from fellow instructors or championship winning drivers. ABS is a skill equalizer in class and formula racing. Skill equalizers are bad for the sport and bad for spectatorship. When the FIA banned ABS in F1 they specifically stated it was due to the advantage, and you can’t convince anyone that ABS is too expensive or complex for F1…
@Afaik777
6 ай бұрын
I was really disappointed when I’ve tried sim racing for the first time and discovered that there is 0 feedback on pedals, only the wheel has any. Hopefully things like this will become much more commonplace, clutch and break are giant immersion breakers when they don’t provide you with feedback
@simracingden
6 ай бұрын
I agree these will help, or the Simagic Haptic Pedal Reactors, which I've been trying on my Heusinkveld Ultimate+ Pedals lately.
@richardople
Жыл бұрын
Boo, no shipping to Canada :( Sad Panda
@simracingden
Жыл бұрын
There is shipping to Canada I’m in Canada and got it
@andychicago8295
Жыл бұрын
Sold out. 😒
@simracingden
Жыл бұрын
Which pedals do you need them for?
@gruisman
Жыл бұрын
verry nice destruction of the name heusinkveld lol
@simracingden
Жыл бұрын
If your referring to my pronunciation my apologies, I’ll have to practice for the next one ☺️
@atechcheck
4 ай бұрын
ffs stop talking for a sec and let us hear the things and what kind of vibration/noise they produce....
@Azza-25
Жыл бұрын
Hands up everyone who has driven a race car where the pedals vibrate ? Yeah this is a pointless piece of hardware. If you think you can replicate the pedal feel of a lockup or wheel spin by using a small motor to vibrate the pedal i'm guessing you have never actually locked up the brakes in a real car. Brake pedal shudder etc can't be replicated with this type of device. If it makes your sim racing feel more immersive then maybe its a good thing, but by no means confuse immersion with realism, this may be one of the dumbest pieces of sim hardware I have seen so far.
@freeemail6299
Жыл бұрын
Rumble motors are useless. Main SIM iRacing does not send correct data to set this to activate when let say wheels are spinning. And if you need this to know when abs is kicking in, then you need more practice.
Пікірлер: 136