I bought this workbench and I absolutely love it. It was so easy to put together I’m a small elderly woman and I did it by myself and could not beat the price just incredible I buy another one and just put it in my kitchen it’s not nice
@Rainbowrobb
Жыл бұрын
I wish the drawers actually fit like this
@DakotaMartinez32
Жыл бұрын
I cant even figure out how to put them on but it sure isn't just like that
@barlosxantana
5 ай бұрын
If you have trouble getting the drawers in, make sure the drawer slides on the desk easily accept the drawer slide on the drawer itself. It should go in easily. If it doesn't, and is seemingly being blocked by a small notch, fret not.. turn the slide hardware around on the drawer itself and voila. The stickers/instructions/user error cause this. Hopefully I could help.
@UDeMaio53
3 ай бұрын
Yup, if you assemble the drawers per the instructions, you end up with the slide mechanisms being on backwards.
@allwheeldrive
8 ай бұрын
Couple of important things in assembly. 1) I'd suggest using a dab of glue on the woodscrews. They can be overtightened very easily and it's good backup. 2) The drawer issue...which is probably why most people are here. For clarification, the sliders mounted ON the drawer must have the OPEN end facing the back of the drawer; the tab end should face the front! For the record, the instructions were written by amateurs. Even the first few instruction are inadequate, particularly visually: hard to tell where you're supposed to start. There should also be close-ups of how things are connected, and those damn sliders should be highlighted. Also, I had extra hardware left and NOTHING was left undone. Makes you doubt things unnecessarily; not a good thing in the garage at 11P. (an old product guy, I understand versions of self-assembly, but you really need to stay on top of that stuff). Harbor Freight! If you get things like this addressed BEFORE product is in a final ship state, you'll save a WHACK of phone calls and nasty emails. The product itself is quite good!
@vek2269
9 ай бұрын
Anyone having issues with the drawers look at 5:18 - make sure the metal tabs on the drawer slides are at the front, not the rear! I'm not sure if they were installed incorrectly, or if I put the front on the wrong side, but it was frustrating until I realized they were backwards. Easy enough fix to just unscrew the slides and flip it if you've already got it together backwards
@ronhoover5516
9 ай бұрын
This. I made the same mistake and had to correct myself on the first one I installed.
@igorsolomatov4743
8 ай бұрын
It is not your mistake, instructions are clear and wrong :)
@Utahforrest
7 ай бұрын
This comment saved me. I flipped the rails and it worked. I think the #11 “left side” panel is really upside down so people put it on the right side (maybe) and thus the rails are backwards. Instructions are confusing at this part and every single negative review on it it’s due to people who can’t get the drawers in. Without this comment I would’ve been left scrambling trying to bend it in. So frustrating after putting it all together for a few hours! Thanks!
@durwoodmaccool890
7 ай бұрын
Well, I'm off to the garage to look at some stuff. Thanks, youtube commenters. Shoulda watched and read this first.
@Ms_AP_
10 ай бұрын
The build went great until I got to inserting the drawers. They only go in oart way then won't go any further. 😢
@paulharvey5505
8 ай бұрын
Same
@Jellyballs
4 ай бұрын
LoL First drawer was successfully(top left) top right.. no damage, aligned well.. Makes grinding noise and comes out too far and doesn’t go back in all the way.
@rogeramadon4064
6 ай бұрын
EXCELLENT video - Thanks for sharing! I read quite a few mixed reviews egar dthe quality, condition it arrived in and difficulties trying to install the drawers. I foung out the bench goes on sale next week at Harbor Freight and I think I will get one!
@nathanschneider6884
6 ай бұрын
Of course it will go on sale soon since I got mine today. Hahaha
@jebbbig
Жыл бұрын
Thanks for the video. You made it so much easier
@drewblack7805
5 ай бұрын
Without this video, I'd still be trying to figure out how to put this thing together. Many thanks!!
@domosautomotive1929
2 жыл бұрын
I would put some wood glue on all those screw joints.
@JViello
4 ай бұрын
Came here to suggest the same for all mating surfaces. Makes for a MUCH more sturdy piece. Especially if you scuff up the mating surfaces since they are factory finished.
@f.hababorbitz
8 ай бұрын
I just picked up mine that was ordered as it was not in stock at my store (1-7-2024). The previous two I have, had some particle board for the drawer assembly supports. Also they have 4 small drawers. And there was some tolerance problems with the width of the drawers vs the mating slides. This new one is all wood except for the drawer bottoms, and has the large bottom drawer. Assembly went without any problems. I assume there were complaints that longer tools could not fit in the smaller drawers. It's a good change.
@christurner5473
2 жыл бұрын
That’s definitely a beautiful table
@cinnreds18
Жыл бұрын
Good video. The bench seems well made. I am actually impressed
@texasbtc
Жыл бұрын
SOLID workbench. Few tips though, drawers need to be pushed in with consistent pressure equally on both sides. Once set they are nice. Also, use a T25 drill bit and throw that cheap short Allen wrench away! Set drill to low setting though when using for screws or can over torque. Very happy with this until I’m able to build a custom bench. Thanks!
@mpc79
2 ай бұрын
Thank you so much. This build was challenging to say the least and the video was extremely helpful! Great bench though.
@darrelcockman1817
Жыл бұрын
I want him to do it..he works fast!😂
@charlespayne1909
2 жыл бұрын
Dear harbor freight. My go-to items you sell are ; Hercules tool backpack , zurich 15s , icon digital torque wrench , Viking 3400 jump box , earthquake 3/8 × 50 ft. Industrial air hose reel , icon master fuel injection service kit , icon swivel 1/2 impact sockets, icon double box flex ratchet wrenches , icon 0° double box ratcheting wrenches
@logiclust
12 күн бұрын
how much weight can those drawers hold?
@carlsalmons2602
3 ай бұрын
Great vidio
@charlespayne1909
2 жыл бұрын
Dear harbor freight. The daytona 22 ton jack stands is awesome.
@ericg5877
2 ай бұрын
These drawers are a nightmare. I regret buying this at this point
@chaspruitt2610
2 жыл бұрын
Nice!!! 👍🏼😎 #1
@ronaldleebarbour2161
Жыл бұрын
Is it possible to locate vise on the left side instead of the right by reversing the top?
@ronhoover5516
9 ай бұрын
I think you can do this.
@XER239
Ай бұрын
can this be painted or is it clear coated?
@PCMenten
2 жыл бұрын
Who performed the music?
@diamondbracelette
2 ай бұрын
Fiddle McPickenbocker
@tommygamba170
9 ай бұрын
They modify the drawers for the video. The draws won't go in unless you bend the back tabs so they don't catch
@kaitkehoe6552
9 ай бұрын
I figured this out: the part of the drawer slide that came attached to the #11 and #12 drawer sides was installed backwards. Unscrew those, flip them around so that the tabs are at the other end, screw back in and problem solved!
@vek2269
9 ай бұрын
@@kaitkehoe6552 Naturally, I struggled with this yesterday and found no comments, but today someone also figured it out haha.
@CullenJWebb
8 ай бұрын
The metal tabs should be at the front of the drawer, not the back. You may have installed the sides backwards.
@susanbodette616
8 ай бұрын
You can also just switch 11 and 12. That is the same as the video@@kaitkehoe6552
Пікірлер: 43