Unsprung full face clutch and lightweight flywheel purchased and installed. Clutch is not an on/off switch like he said. It is very able to be daily driven. Clutch pedal does have a much better and stronger feel. Definitely grabs a little harder being unsprung but for the most part I’m very happy with it. Much more drivable than the 6 puck would have been. Figured I would comment because I was definitely looking in the comments when I bought mine.
@dumbmoney9499
Жыл бұрын
Installed in 1990 Nissan 300zx n/a. Little more hp than stock.
@audioamateur
6 ай бұрын
How's the noise/vibration?
@DJToneRI
6 жыл бұрын
I've spoken with Spencer at Z1 a handful of times, and he has always been very helpful, patient and well-informed. I've found him to been the most knowledgeable guy they've got down there. Thanks Spencer!
@germanss8851
7 жыл бұрын
You guys should post more of your products
@konradchristen
4 жыл бұрын
"If you've ever driven a car like that it sucks....*holds up unsprung full face disk*.... won't suck!" I died 😂
@PerfectedAuto
7 жыл бұрын
Nice detailed video with good information and explanations.
@jaymayjay315
2 жыл бұрын
Bless your soul for this video 😩
@jasonpooler6811
Жыл бұрын
Very helpful. Thanks man
@germanss8851
7 жыл бұрын
Short shifter and solid boot kits
@robertbarbeeyourrealtor8794
3 жыл бұрын
“Won’t suck.” I’m sold, take my money
@CJdriftZ
2 жыл бұрын
9:05 clutch kicks? you have my attention!
@spicywater123
2 ай бұрын
Hows the chatter with that single mass flywheel? Aren't flywheels supposed to be heavy in order to store energy while spinning?
@BO_BILAL
4 ай бұрын
Is the z1 clutch kit the best in the market?
@torvarrisevans7254
2 жыл бұрын
Hi , can I drag race with the midweight flywheel
@dagazenterprise
4 жыл бұрын
I know its a subjective question but how much more noisy is the light weight TT cluch in the Z32 platform?
@edcadiri8720
5 жыл бұрын
How much more chatter will I experience with a Mid wt 21lbs flywheel in comparison to the OEM ?
@Agenthutchins
5 жыл бұрын
Ed Cadiri at low idle rpm it will be more pronounced than a somewhat worn factory dual mass flywheel, however if the flywheel damper is completely worn it won’t be much worse IMO.
@torvarrisevans7254
3 жыл бұрын
@@Agenthutchins Hi , can midweight fly wheel be use as a daily , does it in crease performance
@destruxandexploze2552
2 жыл бұрын
@@torvarrisevans7254 It could be used as a daily I think, the performance increase would be noticeable, but not major.
@torvarrisevans7254
2 жыл бұрын
@@destruxandexploze2552 thank bruh
@GHOSTBROWNz
Жыл бұрын
Catch this sale going on ppl it’s getting hot
@JDM_PLUS
2 жыл бұрын
How streetable / longevity does the Nismo twin disk have and provide?
@BigMidge86
7 жыл бұрын
My jdm slicktop tt is making a metal friction noise only when clutch is pressed in. Pilot bushing? A shop here in wa wants to charge 6-700 a tranny exhaust and clutch maintenance? Does this all sound right?
@JesusHernandez-fo7ti
3 жыл бұрын
Can you use a oem flywheel with the z1 kit clutch
@Z1Motorsports23
3 жыл бұрын
Yes our clutches will work with OEM flywheels.
@ProjectZGarage
2 жыл бұрын
What clutch would you recommend for a 900hp 350z?
@Z1Motorsports23
2 жыл бұрын
OS Giken Twin
@darrelltuttle8298
7 жыл бұрын
Just installed a street performance clutch in my G35 coupe. Has anyone figured out a way to get rid of clutch chatter.
@cincysilvia8807
7 жыл бұрын
i think it's one of those things that were just gonna have to deal with due to design my 04 z chatters and my 08 whines like a 2 year old
@Z1Motorsports23
7 жыл бұрын
The "chatter" you're hearing isn't actually the clutch moving around, its the internals of the transmission. Usually an OE setup is heavy, therefor more weight through the entire rotating assembly, which helps dampen the sounds of the transmission. By putting on a lighter setup this will cause the internals to make more noise. Nothing wrong with this, just takes some getting used to.
@Homelesswhiteguy
6 жыл бұрын
Stop being a bitch lol
@Agenthutchins
5 жыл бұрын
Have your tuner bump the idle rpm up maybe 100. It may smooth it out enough for you.
@Enkies
3 жыл бұрын
just got the kit. midweight unsprung
@coochiefarts
3 жыл бұрын
How’s it treating you?
@Enkies
3 жыл бұрын
@@coochiefarts get it, just make sure you torque everything to spec and bleed your clutch line/reservoir
@torvarrisevans3961
3 жыл бұрын
How does the unsprung clutch feel , did it made a difference in performance ,Is it overly progressive . What u recommend it for a daily.
@Enkies
3 жыл бұрын
@@torvarrisevans3961 honestly i ended up switching to a sprung clutch because Z1 didn’t have that item in stock and that was the only part missing so i told them to switch it out with what they had available because my car was just sitting.. midweight flywheel pressure plate sprung clutch this kit feels like a stage 2 kit. it’s dailyable for sure but i would probably get unsprung next time just to try it you know?
@torvarrisevans3961
3 жыл бұрын
@@Enkies ok bro cool , did you notice any performance difference with the mid weight fly wheel and. Chatter over the stock fly wheel .
@BigMidge86
7 жыл бұрын
My jdm slicktop tt is making a metal friction noise only when clutch is pressed in. Pilot bushing? A shop here in wa wants to charge 6-700 a tranny exhaust and clutch maintenance? Does this all sound right?
@tomr1107
7 жыл бұрын
my first thought would be the throwout bearing. If he is replacing your clutch and doing some maintenance to your exhaust, the 6-700 figure sounds like a good deal. btw, nice car.
Пікірлер: 59