Hi! I would like to cite from the manual: "Configuration using push-buttons Press the programming button on the Z21 detector for at least 1 second; the white program LED starts to flash. Activate a magnet article with the address of your choice within the next minute. The magnet article can be activated using the Z21 App or another input device such as the MULTIMAUS. The address has been accepted by the Z21 detector after the white program LED has stopped flashing." I don't really understand. Does it mean that I can control any function directly from the detector (similar to the LocoNet)? Anyway... have I possibility to dedicate one or more function to the occupied or free status of a track section whithout advanced computer system? That would mean a basic automation only with Z21 mobile app.
@philnewman1110
7 жыл бұрын
James, thank you very much, really appreciate that!
@DCCtrainautomation
7 жыл бұрын
Phil Newman kzitem.info/news/bejne/op2mu2WakZyibGU
@MGGRLW
6 ай бұрын
What is a detector with AppZ21 for? For display only? Cannot reference a route. The ideal would be to be able to make routes where the signals were referenced to the position of the switches and the occupancy detectors (track circuits).
@DCCtrainautomation
6 ай бұрын
The Z21 app does not do this function you are describing. You would need iTrain or something along these lines.
@philnewman1110
7 жыл бұрын
Great video James, very informative.
@dario86707
2 жыл бұрын
sorry for the operation both for braking and for the automatic start of the treono I have to program the decoder from the pc? thanks
@ClinchfieldModelRailroad
7 жыл бұрын
Hi, so will this unit only work on the R-bus ( no Railcom ) for the DR5000 ? No CAN bus on the DR5000, so no Railcom even if the firmware is updated, right ? Also can you test it connected to a DR4088 R-Bus and then the DR5000 ?
@carmelocatalano307
3 жыл бұрын
Does it work with Z21 white one? Or just the black one?
@h.kemalsuher2821
4 жыл бұрын
Hi Sir, how are you? Can you please help me about the connection? Most of the documents are in German, if you can show me the connection it will be great help. I mean the cable connections among z21, z21 detector and tracks (2 blocks). Thank you in advance. Best regards
@aponsin
5 жыл бұрын
Hi, thanks for the very informative video. I am looking for information on how I would go about using the 10808 (or 10819) to also detect rolling stocks presence ? Any tips/hints ?
@AH-kf7vl
5 жыл бұрын
James, I have the same Roco detector and Z21 and using itrain as you have in your video. I can't figure out what address to set in the itrain for the detector to show occupancy. I have 8 detectors which work fine in the Z21app but I can't see the detection in itrain program. In the Z21 maintenance tool the module address is set to 2. Can you please advise or show your setup?
@DCCtrainautomation
5 жыл бұрын
Alfred Hager what address have you set the unit to?
@AH-kf7vl
5 жыл бұрын
@@DCCtrainautomation The Roco 10808 is set to address 2
@alanoes1
6 жыл бұрын
Hi Can you show how to set this up with the Z21 app Also could it be used with reed switch detection Cheers
@ClinchfieldModelRailroad
7 жыл бұрын
So if Digikeijs releases their DR5088RC it will be cheaper and have double the detection with Railcom, right ? It just won't work with the Z21 since it's a Loconet device, right ?
@DCCtrainautomation
7 жыл бұрын
John Zajdler from what we know yes.
@philnewman1110
7 жыл бұрын
I would like a video showing how to set up the digikeijs block detection units with the black version Z21 if you get a chance please?
@DCCtrainautomation
7 жыл бұрын
Hello Phil ok will do tomorrow as have all the items set up.
@Cookie2k
7 жыл бұрын
Will this detector unit work with an ESU Ecos 50200?
@DCCtrainautomation
7 жыл бұрын
Tase no this will not Work with the Ecos. But there are others that will. Do you want to use the RailCom ability with Ecos? If not then there are many S88N detectors you can use.
@Cookie2k
7 жыл бұрын
DCCtrainautomation Thanks James. Yes, I would like Railcom ability so I guess I’m looking at EcosDetector?
@WilliamSpitzer
4 жыл бұрын
How do you link the z21 to itrain?
@DCCtrainautomation
4 жыл бұрын
William Spitzer Edit> interface> then select Z21
@WilliamSpitzer
4 жыл бұрын
@@DCCtrainautomation I didn't see how you connect the z21 to the computer?
@DCCtrainautomation
4 жыл бұрын
William Spitzer the computer is wireless connected to the router of the Z21 and then use the above info to connect!
@morenomazzini2327
7 жыл бұрын
Firmware 1.30 for Z21 is downloadable here: www.z21.eu/Z21/Downloads
@DCCtrainautomation
7 жыл бұрын
Moreno Mazzini great must have come last night will update the video now! Thanks!
Пікірлер: 29