Have to enjoy watching this beast fly , great work Paul.
@paulcooper7162
2 жыл бұрын
Thanks Peter 😊👍 can go but faster on 5s but it's good to enjoy bit slower
@twiggyrc222
2 жыл бұрын
Once again nice job Paul
@paulcooper7162
2 жыл бұрын
Hi 😊👍 thanks,it's on the lower voltage 5s is better
@twiggyrc222
2 жыл бұрын
@@paulcooper7162 Hey I just want to say thank you for the info on all the cool upgrade this little boat will fly across the water grandkids just love it but I lost the pin to the rudder Is there something I can put in there or can I order a pin from somewhere
@paulcooper7162
2 жыл бұрын
@@twiggyrc222 Not a problem I'm happy to help Yes the pin comes out,I just used a drill bit same size and use a hacksaw to cut off and either but if superglue on the top area of pin and tap it in quicky
@twiggyrc222
2 жыл бұрын
@@paulcooper7162 you upgraded your shaft on your SR 80 pro to a 4.76mm Strut Will the stock flex cable fit in that? Not happy with the stock strut can’t keep the insides in it
@paulcooper7162
2 жыл бұрын
@@twiggyrc222 You can buy a 4.76mm strut and run a 5mm drill through the bushes to 5.1mm and stock flex shaft will fit
@iLouieTube
2 жыл бұрын
Beast! 🚤
@paulcooper7162
2 жыл бұрын
Thanks 😊👍 how's your one?
@iLouieTube
2 жыл бұрын
@@paulcooper7162 not even started building it yet, had alot on in work an life in general just had my deliveries for my cars though so I'll be building them up over the weekend, then I'll get back onto my boats, I wish I had more time to enjoy them mate, love watching everyone else's vids though 😎👍🏻
@paulcooper7162
2 жыл бұрын
@@iLouieTube I can understand that,each boat takes alot of work
@brunoandre606
Жыл бұрын
Paul, I have a project to do how can i get in touch with you?
@paulcooper7162
Жыл бұрын
On KZitem 😊here in the comments
@jamesatkinson7517
2 жыл бұрын
Man they have an ugly deck.
@paulcooper7162
2 жыл бұрын
😂👍.,I've got several upgrades today changed motors around in my other 3 boats worked out well,TP4060 1650KV going into Sonicwake V2,SSS 4092 2140kv motor going into Traxxas M41 cat with ZTW 200A ESC looking forward to that and the Sonicwake motor 4068 1900kv into the Vector SR80 with ZTW 130A till I get a bigger esc
@jamesatkinson7517
2 жыл бұрын
@@paulcooper7162 good grief that’s a lot of work right there. Love those choices Very interested in seeing the SR 80 run Great set up and lots of work on that one.
@paulcooper7162
2 жыл бұрын
@@jamesatkinson7517 😊 changing motors is easy on the Traxxas M41 and SR80 in Sonicwake what a mission,I had to glue the motor in with superglue as all the screws threaded the plastic so easily.Thanks me too looking forward to see Vector going on the water.How far are you away from your next boat going?
@jamesatkinson7517
2 жыл бұрын
@@paulcooper7162 I am no good at video I only run mine for fun. One day I may get some head mounted video recorder but not just yet. I ran my 4 s 26 fe rigger this morning a few times. So much fun pretty good run time since getting a abc H5 modded by Chris at dassboata ,it’s getting 117.7 (73 mph )and no temps above 45 c it was lifting the LH sponson as it approached full speed and flipping I tried turn fin angle and I lengthened the LH boom rods to make it less likely to lift or roll that side up and this helped but the last thing I did was add a small 50 mm long foam wedge onto the LH sponson so the wind at speed pushes it onto the water it’s tapered from zero to about 18 mm tall and is the width of the sponson it’s held on with double sided tape inline with the rear tip of the back of the sponson ride plate. Problem solved no loss of speed and no added weight. I also ran my 33 fe and it’s got lipo issues or something 12 kmh missing no idea why no temp issues I tried a smaller lipo that’s brand new but is only 3300 mah not 5000 mah both are 100 c it’s all I had to try, and both exactly the same speed wiring looks all fine temps are all good I even took the 4068 1850 kv back out and put the 4092 1650 kv back in it and still same speed about 118 kmh the 200 amp seal ZTW might have changed it’s settings some how I am at a loss. I’m waiting to see what your sr80 does before I decide on what hull is next on the V bottom. Also have a rocket 3450 kv 2968 coming for a 26 fe rigger project in carbon fibre or if I change my mind I may put it in my small 3 s rigger currently running a 3648 with a 3814 octura getting 80 k it’s only a bit over 450 mm long so much fun so little time. Oh and so little money.
@paulcooper7162
2 жыл бұрын
@@jamesatkinson7517 Fun is good 😊👍 I mount my wee camera I to the side of my transmitter. I've been thinking of getting one of those rigger kits,it's good you have the patience to get the rigger going well.theyre very fast.Was it the timing gone out on ZTW 200A as my ztws stutter if at in 0 degrees,I set to auto. I just fitted SSS 4082 2600kv motor and flycolor 150A ESC into Vector SR80 👍
Пікірлер: 25