One of the nicest motorized bikes I've seen on KZitem very good job very clean
@JamesPiccone
2 жыл бұрын
I'm getting back into it slowly, I've been super busy the past year & a lot has happened. Bro excellent job on the bike, I missed your videos. I really like this phantom 85 setup.
@shannon6815
2 жыл бұрын
Sweet ride, love the way that pipe sounds and those forks are sweeeet . Great job but once get that thing broke in need to get that 4 stroking cut down some. 👏
@nurzrachit7133
7 ай бұрын
Man you know how to make anything look good. Personally I can't stand the look of the peanut tanks, but thissun is acceptable. I've really appreciated the ones you build on motorized bicycle frames and felt fakers. I have a Phatmoto and it looks pretty slick too, thinking about getting another just to use the bicycle part and make it a two stroke beast. Either that or a predator ghost or something powerful. Thanks for the videos man, I have a lot to learn before I figure out how to get one to go 75mph.
@jawauncobb
2 жыл бұрын
Nice ride sir can’t wait till you break it in love the modification sir
@cesarpagan4640
Жыл бұрын
I love phantom 85 muffler I cut it just to weld a 85 cc two stroke dirt bike pipe on it It works so well.
@JoseDiaz-kv5cz
2 жыл бұрын
I just got mine!, and halfway into breakin, little nervous, but so far so good, and they gave me mini roller bearings for upgrade on piston
@kylep3764
2 ай бұрын
I have a phantom 85 v3 on a cheap walmart bike with 29" wheels, a 36t sproket, and about 3500 miles on it, and still run 25:1 fuel mix as a bit of insurance.. im sure im losing a little power from that mix but it still has plenty.. At about 1200 miles i took it apart and used a dremel to port the intake and exhaust on the head, being careful to not change the timing on them and just that and a good ngk plug made a huge difference. Im hitting 49mph on flat ground and i weigh 240lbs lmao.. it rips!
@diydarkmatter
3 жыл бұрын
looks good will sound better once its broke in and re tuned im sure . i dont think it will be long and they will come out with parts for this engine . and that will open up new expansion mods for the yd 100 . basically making it easier for yd 100 owners to turn there yd 100's into phantom 85s . cause we all know it is just the head and piston and muffler that is new . the bottom or lower case is all yd 100 right to the crank arm its self . if they dont come out with replacement parts for it that will be sad in its self making the motor not worth the cost . we all know how being able to rebuild these china dolls is fundamental. not to mention the fact that being able to mod them allows us to grow with out braking the bank to do so .
@darknessdanger
2 жыл бұрын
That 85 phantom engine just arrived in Mexico but the dealer does not want to sell it yet because he waits for the dollar price to increase more to sell it more expensive, like $ 1000 dollars approximately.
@blackswan0017
3 жыл бұрын
I have the same frame. Hub mounted sprocket adapter was how I got around the chain issue
@danerpdr4759
Жыл бұрын
I'm planning a 2300km cycle trip, they say this engine is excellent.
@KB_Joys
2 жыл бұрын
I love how they sound. They do sound like a chainsaw, lol. I wonder how much more powerful it would be with a chainsaw carburetor?
@JAM-zb2vh
Жыл бұрын
nice and clean build great job brother.
@ArthronOfFir3
3 жыл бұрын
yo, love the setup. as for the clutch lever, i used to use a 3 speed derailleur shifter for 2 builds, would recommend that over the levers due to if you crash the bike on that lever, you can break it off. also I'm working something for the future of motorized bicycles, probably a potential frame, while I'm working on cruiser build to be a fully themed bike(Iron Maiden), for it's for a special cannonball run I'm doing ok these bikes (pompano beach to key west and back) and i would need tips for this trip work out perfectly (will let others join me for some parts but majority of the trip I'm looking forward to experience with a small group of people who are on that trip. hopefully I'll see about this build more ad well how much that engine can pull.
@johnsheetz6639
3 жыл бұрын
Iron maiden bike! Cool! Call it eddy!
@ArthronOfFir3
3 жыл бұрын
@@johnsheetz6639 was planning to but wouldn't have the same ring unless i have an Eddie on the build
@josephwoodall832
3 жыл бұрын
Very cool are these "cannon ball runs" common?
@ArthronOfFir3
3 жыл бұрын
@@josephwoodall832 as far I'm aware, no, for mostly it's reserved for motorcycles that are old school. however. I'm doing a solo run for my trip to key west though i need to make it ready for my build to last long enough to let me be alive for 400 miles(i have to make a return trip)
@orlandomattos1000
Жыл бұрын
Aqui no Brasil gostamos de correr,acima de 60 km nas bicicletas motorizada.
@danerpdr4759
Жыл бұрын
Se não for assim eu nem quero
@midwestmotorbikes2696
3 жыл бұрын
Don’t stock yd100’s go like 40mph? I do think the kit has potential with the right expansion chamber and a bigger carb. Maybe even using a g2 reed might give ya some gains. I think the kit does have potential for 50-60 mph but i recommend replacing the bushing in the piston with something of better to ensure a longer life
@wtcamer
3 жыл бұрын
It's not broken in and the timing needs to be retarded a bit. 4 stroking a lot. Also that 40 mph probably isn't w/ a 220lb rider :)
@aussieferrari6624
2 жыл бұрын
I have a non broken in yd100 and i weight 50kg and it only goes 25mph with a smaller sprocket idk why its so shit and no air filter
@midwestmotorbikes2696
2 жыл бұрын
@@aussieferrari6624 I’ve never bought a yd100 so I can’t actually tell you what to expect besides what other people have put on the internet. I will say that these motors are tuned rich from the factory to help people not blow em up, but might make them ride a little slower. Some cylinders may have better ports/port timing than others and you need to be able to make decent power in order to pull a smaller sprocket.
@devinxander102
3 жыл бұрын
I’m In the process of building mine right now and I was wondering how u put the throttle lever on urs or where to buy one
@MJTechChannel
3 жыл бұрын
It’s simply a clamp on style. Just tighten the bolt and that’s it!
@underdogontheappalachiantr9646
2 жыл бұрын
May I ask a couple of build questions on links to your Thrumb throttle Front forks Tire set up Braking system. Thanks I'm looking to build my 1st and have the yd100 coming soon. Excellent channel it helps me greatly..thank you
@MJTechChannel
2 жыл бұрын
Hi! Yes all those links are in the description of the video! Thanks!
@underdogontheappalachiantr9646
2 жыл бұрын
@@MJTechChannel I'm sorry. I should have seen all that. You got this nailed.. thank you
@Westhelockpicker
Жыл бұрын
I hate waiting to get it broke in. It's worth it but I'm impatient and it's still cold where I live. It's actually snowing right now so when the weather is a little better I go for a ride but any longer than 20 minutes and your freezing but it'll warm up soon and do you know what size jet it comes with?
@ChuckHaney
3 жыл бұрын
I keep seeing throttle cables with a boot at the carburetor end, presumably to keep out water? Mine didn't come with one of these. Any idea where I could buy one?
@jhonnytheboy1975
7 ай бұрын
Hi mate ! I want to built one , same engine … are they really reliable?? For daily use, maybe a trip?!? Thanks Mann
@Jayden-kd3kg
2 жыл бұрын
Hey MJ, I was wondering which bike are you using for the phantom 85, I’m getting the Phantom 85 today and I’ve been wondering which bike would fit and work best for this amazing motor.
@justanothermotorizedbikech5138
3 жыл бұрын
Beautiful build brotha
@AlreadyDeadInside83079
2 жыл бұрын
Great looking bike!
@fr33dumb0
Жыл бұрын
What frame is that? You said it's aluminum but nothing about where to get it or who makes it...
@SHIVSHANK
2 жыл бұрын
My only question is was it 4 stroking cuz you wernt following the powerband or it's a ignition timing issue
@joebrown967
3 жыл бұрын
Hello I was wondering if you found a solution for the phantom 85 wristband bushing thank you
@mflbikes1870
3 жыл бұрын
Switch to a normal bearing and 10mm wrist pin. Put bushings in the pistion instead.
@tanksbikesandcars3420
3 жыл бұрын
Is your Electra a tall frame or not. I have the same bike but it's a 26 inch tall frame. And I want to get some forks but the neck is so long on it.what size of fork did you have to get
@wtcamer
3 жыл бұрын
retard the timing so it doesn't 4s so much. Will likely loose some of the very top end, but it will be a much better ride all around.
@mikerammelt2420
2 жыл бұрын
Have you tried playing with the mixture and timing to control the 4 stroking and hi idle. Any vacuum leaks.
@kevincooper3765
Жыл бұрын
what oil do you use and what ratio or ratio's. why do you use a rag joint instead of the three point solid sprocket mount.
@josephwoodall832
3 жыл бұрын
Nice video. I just blew that motor up. It was fast but now I'm struggling to find a new piston and rings the lower end is easy to replace and the cylinder sustained no damage but the piston and rings are gone I'd like to rebuild it.
@MJTechChannel
3 жыл бұрын
The ms380 piston will fit. Just needs to be windowed.
@josephwoodall832
3 жыл бұрын
@@MJTechChannel ? Really? I thought it had to be 52 mm
@josephwoodall832
3 жыл бұрын
@@MJTechChannel I see it now. I wonder though. Can I just leave out the Reed valve and not window the piston?
@josephwoodall832
3 жыл бұрын
@@MJTechChannel or where might one get the piston windowed?
@MJTechChannel
3 жыл бұрын
@@josephwoodall832 It will run without being windowed
@qgoods8036
3 жыл бұрын
Awesome build!!! Do you know if those forks fit Cranbrooks?
@MJTechChannel
3 жыл бұрын
If you have a 1” fork tube then it will. I believe you do 😃
@iAmYGB
2 жыл бұрын
Where did you get your phone holder from I’ve been looking for a safe one for a while ?
@ctdmowing
2 жыл бұрын
Hey, I have the same bike and engine. How do you mount the bike to the fat tube of the Hyper bike? Thanks
@frankguzmanceo
3 жыл бұрын
Do you use only half the throttle during break in period? Or can you use full throttle during break in?
@americanpatriot212
3 жыл бұрын
Why dont you update and show us that this motor of yours Blew up?? It didnt last very long did it??? Did they give you this motor to review??
@ThisisTulsa918
2 жыл бұрын
well some tips for you all.. The springer forks nice but the issues i incurred with the forks is the top of the spring plate headset mount will bend eventually, solution is to use two spring top headset plates.. To get to max performance from these 2 stroke engine, is to adjust the fuel cock to a minimum flow..You will feel it kick in like a turbocharger as the carburetor float minimize fuel consumption..last is that after a 2 stroke get so hot it will continue to run without any spark, kill switch will not work..A clutch stall and fuel shutdown will stop engine from running..Last thing is 2 stroke will spit out unburned oil on your bike.. Ride fast or stay at home......
@kevincooper3765
Жыл бұрын
I would think you could cure all those problems with leaner jets and a good tune .
@jimfitzgibbon5492
3 жыл бұрын
What speedometer are you using ? That is nice.
@mjsmjs7905
3 жыл бұрын
Surprised they don't give you a 415h. I would think the regular 415 would be a disaster with that engine.
@MJTechChannel
3 жыл бұрын
Totally agree
@davidsamida3422
3 жыл бұрын
Even cheap 415 is more than strong enough to handle these engines, without problems.
@mjsmjs7905
3 жыл бұрын
@@davidsamida3422 who told you that? My Lifan 79cc 4-stroke destroy them in less than a hundred miles.
@mjsmjs7905
3 жыл бұрын
@@davidsamida3422 you need to get the gold 415h, those things will last thousands of miles
@Adalbertomatos_
2 жыл бұрын
What kind of tire is it where You buy that tires ?
@jeremiherring3852
3 жыл бұрын
Hey thanks for the video ! Is your bike still running good ?
@MJTechChannel
3 жыл бұрын
So far so good!
@7MPhonemicEnglish
3 жыл бұрын
What rear sprocket? I didn't catch it if you told us.
@MJTechChannel
3 жыл бұрын
36t sprocket
@qgoods8036
2 жыл бұрын
How's the phantom holding up
@larryshaver3568
3 жыл бұрын
is that California or Florida?
@MJTechChannel
3 жыл бұрын
Florida
@lifesadventureskeepingitre1180
2 жыл бұрын
I'm going to buy me one of those but I was wondering if I should change out the piston to an ms460. I need your opinion.
@vedabark8591
2 жыл бұрын
Did you end up purchasing it?
@lifesadventureskeepingitre1180
2 жыл бұрын
@@vedabark8591 yes
@davedaisy9417
2 жыл бұрын
How's that springer front end ride
@joneserupinsmoke9161
2 жыл бұрын
Yo mj did ur engine blow up yet? Mine blew up after 6 .10 to 15 ,20 min ride
@dougsignorovitch1493
2 жыл бұрын
Way cool bro. 😎👍
@weasele1
2 жыл бұрын
so what part ofd florida is that im in sebastian looks similar
@larryshaver3568
3 жыл бұрын
will the reed valve make it quieter?
@bryceevans8340
3 ай бұрын
No
@daver4905
2 жыл бұрын
Hey have a question? Does the kit come ready to install out of the box?
@brettthompson6939
2 ай бұрын
WHAT?
@soundqubedkiller5885
2 жыл бұрын
What ngk spark plug should I run with this motor
@faze3rw500
Жыл бұрын
can you make a link for the thrums throttle
@hunterlieske3075
3 жыл бұрын
Was halfway through break in with my phantom 85 and the piston window blew and piston cracked half way through
@MJTechChannel
3 жыл бұрын
Oh no please post a video asap and post the link!
@JC-eq7dw
3 жыл бұрын
same thing happened to me, about a tank of gas into break in the piston shattered.
@jorelldye4346
3 жыл бұрын
Sounds like they should give up on the reed.
@damnthiccassboye7138
3 жыл бұрын
Is it the same case with regular window piston for pk80
@garylee7774
3 жыл бұрын
YD 100 bottom. They are trash. Unbalanced cranks, crappy clutch springs. Had 4 Yds, and all of the clutches gave out. Just buy a Don Butler or Ken Hinson motor. Great looking show piece tho!!
@boydjensen3161
2 жыл бұрын
Say, what speedometer app are you using?
@brandongill4542
3 жыл бұрын
Sweet bro can you link the wheels?
@MJTechChannel
3 жыл бұрын
Got them locally from a store called mzmiami. This is their site mzpartsmiami.com
@MotorizedChuck
3 ай бұрын
The phantom 85v3 is the best engine kit you can buy. Why not pay more from a quality distributor for the $300. It is very powerful but you still need to break it i in nicely
@motorizedbicyclenation53cu90
3 жыл бұрын
Ok so I hear theirs a cheap bushing on the wrist. Any ideas on a fix for that?
@jaayse
3 жыл бұрын
replace it. its designed to be replacable. just replace it if you feel that way. the bottom end is a stock yd100, and yes i think ive heard those motors have that issue. The bushing size is 12x14x15.
@davidsamida3422
3 жыл бұрын
Intake ports are to large in cylinder causes ring snags and piston rock witch wears out already thin cylinder plating instantly. $300 boat anchor!
@jaayse
3 жыл бұрын
@@davidsamida3422 You dont own a phantom I can tell
@americanpatriot212
3 жыл бұрын
I feel the motor is overpriced.. it is 3x the cost of a standard engine. 95% of the parts components are the same. Costs little more to produce. Yes it performs better but NOT 3x better than a simple ported motor.
@MJTechChannel
3 жыл бұрын
I agree with you, but keep in mind that’s something new to the market. Because of the hype, the price is a little jacked 🆙
@ΘΩΔΩΡΑΣΓεωργιου
3 жыл бұрын
Without air filter..??
@artofdisguy3401
3 жыл бұрын
It's a YD bottom end with a new jug and piston. Wait till replacement parts are available and buy the top end and put one together yourself
@dmoore0079
3 жыл бұрын
They tend to cut corners on a lot of these "performance kits". They often include some legitimate performance performance parts, but they'll hold back on other things. Kind of like offering a GT80 case reed kit with the standard cheap muffler or one of those crappy banana pipes.
@jerryb1234
3 жыл бұрын
@@artofdisguy3401 , please explain how a YD bottom-end is any different than a stock 66/80cc bottom-end, other than the spacing of the cylinder-studs?, lol
@0Maeda-l8j
8 ай бұрын
Is this a stock engine?
@chasebowyer1554
2 жыл бұрын
Put a big cool air intake on it
@Emazingridez10000
3 жыл бұрын
what kind of frame is that?
@MJTechChannel
3 жыл бұрын
Its a Hyper cruiser frame
@mustbee-bike994
2 жыл бұрын
I would love to have one of thoes But they are illegal in Canada/Quebec
@huddy._.5517
Жыл бұрын
how long does it take to brake in the engine?
@kylep3764
2 ай бұрын
about 3 full tanks of gas.. but I would do a few more tanks to be safe. I did and I run 25:1 fuel mixture still and I'm running strong still at over 3500 miles
@gl33ck_83
Жыл бұрын
what the range on this bike
@justinbutler8416
3 жыл бұрын
What kind of bike frame is that and how do I order one?
@nickhersheys2706
3 жыл бұрын
It's a Hyper 26" Beach Cruiser sold at Walmart for about $120. Thank me later :)
@justinbutler8416
3 жыл бұрын
Right on any bikes you don't gotta use the universal motor mount? Like online stores?
@Peter_Grekov_91
Ай бұрын
Why the G 2reed is better?
@frankjgornickjr3676
Жыл бұрын
I've built four or five of these without the fenders you get shit splattered everywhere! Not too good riding in the rain either!
@marcosgoncalves3728
2 жыл бұрын
Hello,sou brasileiro do Rio de Janeiro é quero adquirir um motor desses como faço?
@jorelldye4346
3 жыл бұрын
Slow out of the box. To be expected. Will you update this after break in?
@MJTechChannel
3 жыл бұрын
Yes I will. So far we added a RM85 pipe, better NGK spark plug, G2 Reed with a Mikuni clip on carb 23mm, and got 42mph. Still 4 strokes like a bit**. Need to tune the carb better or balance the ignition and should confidently do 50mph! We will keep you guys posted.
@123edwardzpad
2 жыл бұрын
Cool.
@orlandomattos1000
Жыл бұрын
Olá aqui no Brasil começar agora a vender este motor,estou pensando em comprar, um abraço.
@Adalbertomatos_
3 жыл бұрын
You voice sound like from other Channel the mame is la hover
@MJTechChannel
3 жыл бұрын
I’ve heard that before
@PapaFrizArcade
2 жыл бұрын
That Hyper Cruiser frame is NOT aluminum.
@jeremiherring3852
3 жыл бұрын
Man I wana here her rip !
@americanpatriot212
3 жыл бұрын
I would buy at $200-225 but $299 +shipping is way too much.
@MJTechChannel
3 жыл бұрын
Shipping is free.
@gta5grindzxb145
3 жыл бұрын
Shipping was not free on mine. Still not sure I want mine, been hearing too much of them seizing or not even running.
@americanpatriot212
3 жыл бұрын
The motors are junk. They blow up you will waste alot of time & money for screwing with this motor! Big waste!! Mine blew up plus 4 other people!
@tomrockhill8634
3 жыл бұрын
If this engine doesn't get to at least 50, why bother? Yd 100 or triple 40 with a decent pipe and reed valve is gonna get you that.
@keeganhache6667
2 жыл бұрын
I’m pretty sure that frame is steel not aluminum my hyper is steel
@randyrush9856
2 жыл бұрын
Going 30+ mph, wear closed toed shoes and long pants, long sleeve shirt, gloves and head gear. You'll thank me later.
@MJTechChannel
2 жыл бұрын
You are 100% right
@jgbelmont
2 жыл бұрын
MS460 = 76.5cc. It's in the 1122 family. More like an 064 top end.
@OddBallPerformance
2 жыл бұрын
The jug and piston are MS460 based, but they are not direct copies of them either. Stroke on this engine is longer than the MS460 engine, hence the 85cc displacement. Intake and exhaust ports are shaped a bit differently (not including the flanges). The transfer ports are actually fairly close to the same as the original. Port timing is modified a bit but not too far off. These won't rev as high as an MS460 can, but make a lot more power down low.
@deleted203
2 жыл бұрын
Please get some shoes next ride. I hate seeing people lose a toe when they could of prevented it. Sounds mean.
@catsbyondrepair
2 жыл бұрын
Ain't no such as a bolt on kit you always end up having to fabricate something or modify something
@ArthronOfFir3
3 жыл бұрын
ummm i think you might want to see my sprocket setup
@awakendsails
Жыл бұрын
Beef it up until it can leave the atmosphere lol
@tostig7795
3 жыл бұрын
Been checking gas bike laws here in Florida and it seems I may need to get a moped tag. What BS , if it's electric po po won't mess with you. Gas motors are in a grey area and who ever wrote the laws must of had his head up his you know where.
@michaelgamba369
3 жыл бұрын
Get a different style chain tensioner. If that thing loosens up it will fall right into the rear.rim and lock it up. One thing I've learned from my daily drivers anything that can fall into or onto the tire is bad. I wanna get a mean motorized bike but I'm addicted to my puch. Yeah you could use some different jetting and your getting some pretty loud topend noise. Try putting another gasket between the top and bottom end and that should go away. God bless please stop at stop signs and red lights it will not only keep you alive but people find it rude and disrespectful when you dont and then they call the cops and that's never good
@THiAGO33800
Жыл бұрын
I should have lowered the choke so she wouldn't be cutting
@ELISRACINGTEAM
3 жыл бұрын
😂 the slow bicycle on the planet and we all nkow that and that a fact 😂
@cls_alex13
3 жыл бұрын
That was a speed test?
@MJTechChannel
3 жыл бұрын
Yeah 35-40mph max speed with all STOCK components. 🙂
@cls_alex13
3 жыл бұрын
Has it been broken in yet
@MJTechChannel
3 жыл бұрын
@@cls_alex13 Not broken in yet
@cls_alex13
3 жыл бұрын
Do you believe it can hit 50
@MJTechChannel
3 жыл бұрын
@@cls_alex13 Today I hit 42mph half throttle and God’s my witness.
@djodjodubois9458
3 жыл бұрын
What the cylindre chain saw.?? 85cc motor bike / 6000-12 000tr min Chain saw motor 32 000-48 000 tr min.. I am forestier work end i ave motor bike 85. 6-12000 / 32 48 000 tr min..no is no cylinder chain saw big..the mini scooter yes..tk the nice bike..hi
@alexrrr1887
2 жыл бұрын
up
@robertpolicastro1
3 жыл бұрын
Way more power then a yd100! But still sounds like shit definitely put a x pipe with that carb. 4stroking is off the chain that’s gotta go.
@MJTechChannel
3 жыл бұрын
Totally agree! Mainly wanted to show what to expect out of the box.
@wokeghozt9049
3 жыл бұрын
400 dollar motor yo bike is slow,my yd go faster than that
@davidsamida3422
3 жыл бұрын
100cc, actually 78cc with 1pc cylinder are junk. None of those 1pc cylinder plating lasts longer than 1000miles
@thompsonbrian8791
2 жыл бұрын
😡
@stephenrodgers7824
2 жыл бұрын
The phantom85 is a piece of garbage. Never started. Mad as hell !
@davidsamida3422
3 жыл бұрын
These engines are trash 95% have top end failure before break in period is though. Wrist pin bushing are junk and intake ports are way to wide and cause rings to snag. Overpriced turd! You can build better engine for half that price, $100 ebay triple 40mm 80cc kit and $30 ms460 52mm chainsaw top end' $20 G2reed.
@americanpatriot212
3 жыл бұрын
Junk motor. They blow up dont waste your time and money
Пікірлер: 178