So bolt and hexagon only kit gets rid of the round alignment tabs right?
@NYskyHI
3 ай бұрын
What sized wrench is required for the 3rd gen tacoma kit?
@northcountryoutdoorsusa
5 ай бұрын
That's a very good looking product. Awesome instructional video!
@DoobydoMoto
5 ай бұрын
Curious your welder setting were at for this?
@mrbmd710
6 ай бұрын
Any coupon codes available?
@jaimegarcia213
6 ай бұрын
Wish yall made the Fj Cruiser bolt kit greasable id def buy the kit with the tabs and all.
@fernandopinzon1578
7 ай бұрын
Sorry if this is a stupid question but why are the cam tab key seperate from yhe plate?
@SEQUOIALOVER2002
9 ай бұрын
I ordered some but I’m not getting a tracking number. Or any response? Low long dose it take from cali to Florida
@KPOffroad
9 ай бұрын
You ordered these yesterday and it's a weekend. It takes 1-2 business days to prepare an order.
@youonlyliveonce1432
10 ай бұрын
Whats the purpose of that part? What if i leave it stucked/broken? Is the vehicle dangerous to drive? Thank you
@nonamenoname1737
11 ай бұрын
didn't see any kits for the 2nd GEN 07 TUNDRA, just 1st Gen...am I missing something, or out of luck!
@KPOffroad
11 ай бұрын
Unfortunately we haven't had much interest in the 2nd gen Tundra platform and do not offer a kit for it at this time.
@FollowTheCloud
11 ай бұрын
Do you have to do the rear wheels too , or only the front wheels ?
@tannerkelber4090
11 ай бұрын
Typically only the front wheels. Depending on the model vehicle, this chop clears 33-34s if you cut it deep enough. The rear needs minor trimming on fenders depending on the model as well.
@georgesantiago6005
11 ай бұрын
Do both side aligne the same number of lines? Im having some shaking on front and their not the same numbers of lines.Hope you can help. Thanks
@KPOffroad
11 ай бұрын
In some cases yes but usually no. It really depends on your bushings, suspension setup, lift, etc. The best advice I have is to bring it to an alignment shop and have them verify everything.
@georgesantiago6005
11 ай бұрын
@@KPOffroad some can't trust them.
@tsslaporte
Жыл бұрын
Great video but I just want to mention that this guide is missing torque specs. Stover Nuts run on torque will need to be accounted for. Whats great about this kit though it that it uses a normal bolt which should be able to handle more torque, which has a higher clamp load which means the alignment will hold better.
@KPOffroad
Жыл бұрын
Torque specs are going to vary from vehicle to vehicle. We recommend using whatever the factory torque spec is as to not damage your control arms.
@tsslaporte
Жыл бұрын
@@KPOffroad you need to add run on torque to the factory bolt spec otherwise you are not even matching factory spec. The manual/install instructions should mention this because of the Stover nut.
@CarlosMorales-mx9el
Жыл бұрын
Do you have a kit for a 2011 Toyota tundra crewmax
@jovanivenegas204
Жыл бұрын
I ordered some and saw that some tabs are a bit bigger than the other ! Do the bigger tabs go on the back of the control arm ? And the small ones in the front ??
@KPOffroad
Жыл бұрын
You will need to match them up with the factory ones. On most new Toyotas the small ones go on the back LCA pocket and the large ones go on the front.
@TimmyTheToolman
Жыл бұрын
Thanks for the video Brochachos! I'm going to be installing a set of these on a 1st Gen Tundra soon.
@KPOffroad
Жыл бұрын
No problamo! We're looking forward to it :)
@blakeray3571
Жыл бұрын
Are you using argon gas and oxygen or flux core?
@KPOffroad
Жыл бұрын
This was 75/25 Argon/C02 Mig welding
@jimskatr103
Жыл бұрын
No way!!! I just got these in the mail!! So pumped for this video. These guys customer service is on point!!!
@KPOffroad
Жыл бұрын
We just got the video done too! Glad you're excited! And yes, we do have the best customer service 😉
@amaterasu20jlb
Жыл бұрын
Nice very well explained, I just ordered last week the complete kit!
Пікірлер