And so the blinkers in the same spot or does it have screws
@user-ym9oc7jh6m
3 ай бұрын
Why do none of you mfs show the fucking connection removal
@ATL4Bloc
4 ай бұрын
Amazing vid!!! This helped alot....the switch inside was why i couldnt get it out.
@marcoacosta350
5 ай бұрын
2014 GC Overland here, apparently these have HIDs as well, thank you so much for this video, best video online for sure🤝🏽
@luispenunuri5184
5 ай бұрын
I made the conversion to LED on a 2013 grand cherokke, they light up fine but after 10 seconds they turn off completely, can you help me?
@jesuso1819
5 ай бұрын
Thank You!! Great vid. My right headlight just died. With this tutorial I am going to change it myself instead of paying lots of money to the dealership.
@christinealarcon3877
7 ай бұрын
Thank you, thank you the dealer wanted to charge me $450 to change his bulb. I search multiple videos and yours was the only one who told me about the tabs to move up and down on either side. I am a woman of 61 years old and I did it.
@450brucey2
6 ай бұрын
I'm a 37 yo male and can't fml
@kali_g8578
6 ай бұрын
Yeah dealer be over charging. For one bulb $380 lol I click on them
@fransmare
7 ай бұрын
Thank you, you saved me a ton of pain. Tabs rotate and not the bulb.
@reynaldoesparza6256
7 ай бұрын
Has anyone change the ballast mine burn out
@CodyB-R1
8 ай бұрын
Thanks man took me 20mins
@johnspurrier0001
9 ай бұрын
$300.00 for a light bulb!
@stephaniecaldwell3632
9 ай бұрын
Do you need to disconnect the battery first?
@dillonpaulson7574
9 ай бұрын
I did not, but always good practice to disconnect the battery.
@jfaze401
10 ай бұрын
Do you push both taps before taking out
@mcalann
10 ай бұрын
Could never fully understand instructional videos when everything is done off camera 😢
@BS-bi3hn
5 ай бұрын
I agree. It would be nice to 'see' the light bulb actually being installed. The description is good, but without visuals, it is hard to follow.
@user-hr6dz6bm9k
10 ай бұрын
Thanks this really helped, Yes the tab it turns about 1/4 turn up or down depending on side you feel it. You have to play with it a little as it might be a little tight. This tab is attached to the main light housing so it is just in front of the square housing on the bulb. It can be a little tricky getting the bulb back into the fixture. just have to line it up and play with it a little. Then it will seat and lock the tab once again. Saved alot of money for a little over an hour work.
@chadfisher1858
Жыл бұрын
Do you have to mess with the clips when putting in. ?
@David_Stee
Жыл бұрын
Very helpful thank you!
@jpjelec1
Жыл бұрын
Spend most time installing aircleaner , there are these steel ribbons the case of the bulb goes in first , you have to position it perfectly to allow to insert and twist bulb . You should explain how to get the bulb line up perfectly .
@jeffconner5483
Жыл бұрын
Cant thank you enough for this .video. Helped me tremendously.
@steviebutube
Жыл бұрын
Great video , thanks for sharing
@rickmartinez6991
Жыл бұрын
Very helpful tabs are very difficult to unbuckle. Had to make sure they were both secure on the top and bottom on both sides.
@stephenjordan2460
Жыл бұрын
Absolutely the best video on the web. Thanks so much for tje part about releasing and installing the bulb !!!!!
@ponsholm
Жыл бұрын
Yup, did this myself with the help of this tutorial. Like others have said, those clips are a pain. In the end, apparently the HID D3S bulbs wasn't the culprit. I realized that the high beam "blue icon" on the dash didn't even come on so now I'm lost again. I checked all the fuses etc. but all seem ok. Anyone else out there had this issue with the high beam indicator not even coming on on the dash? Just happened absolutely sporadically and some items suggest the multi switch has gone bad but I don't even know where to start.
@rscottyd
Жыл бұрын
Thank you! that was the most thorough explanation of the tabs i've seen.
@THAREALDONJUAN
Жыл бұрын
Thank you
@diggy82
Жыл бұрын
It's so quick and easy, you weren't even able to do it on camera. Smh. It's not that quick nor easy. So how do you get the band back on, with the tabs.... ?
@TheBowzer01
Жыл бұрын
The description of the "tabs" that must be semi-rotated to release the bulb assembly is huge! Saved me from buying another set of bulbs thinking one was bad after the passenger side didn't originally reseat correctly. Thanks about a $100 or so! FYI: This applies to any of the Grand Cherokees of the WK2 ilk with OEM HID.
@bc2054ever
Жыл бұрын
Anyone know where to find the turn signal and daytime light bulb? Or are they all the same bulb?
@hanscustomshop
Жыл бұрын
Thanks for the video. Helped me with my HID bulb replacement. On my 2014 Summit with Ecodiesel I had to remove two 10mm fasteners that hold the coolant reservoir in place. This allowed me to access the passenger side bulb. Still very tight, but enough room to get it done. I did not have to remove my ECU. My air filter housing was the same as yours. Thanks again.
@tailfirst
Жыл бұрын
The locking collars undo counterclockwise and do up clockwise - seems obvious I know, but in a car thats several years old the rotten things can be very stiff - and the headlight units are mirror image of each other so I ended up thinking maybe they lock/unlock accordingly - ie. one goes one way and the other goes the other way - but no, they both operate conventional way.
@DrunknOdin
Жыл бұрын
Great video. Helped a bunch but now my front turn signal doesn't work. Any ideas/suggestions how to replace that? Or does the entire lamp need to be replaced?
@jagged9
Жыл бұрын
This was an EXCELLENT instructional video! You managed to hit every detail. Those tabs though, what a pain
@mikee3997
Жыл бұрын
Thank you for producing this video it was totally different doing one of these bulbs compared to other ones pull out and replace total time about one hour
@johnkow8884
Жыл бұрын
NO NEED TO Disassemble Components , THERE IS ACCESS HOLE AT THE FRONT OF WHEEL WELL, YOU CAN REPLACE HID BULBS THRU THEM. Search KZitem for right video, there are some.
@jimloges4862
4 ай бұрын
That access hole is very small and difficult to maneuver in. I can’t see how I can get an HID in there (passenger side). My 2018 Trailhawk has a lot of cables bulging out when I open that access.
@terrancetaylor7891
Жыл бұрын
This explanation has been the most helpful. Thank you!
@user-wh3wz2kn4q
Жыл бұрын
This is a terrible video😂 you show absolutely zero disassembly or even install to the passenger side. Here’s a video that shows you the tabs to remove the bulb: kzitem.info/news/bejne/lXyprYugs6CfmIo
@maicodarbel
Жыл бұрын
Thank you very much, you saved me a lot of time and money!! How you explain the tabs is great!!
@phxroadracer
Жыл бұрын
One of my bulbs went out. I read recommendations that you should change both so I did. Now, both bulbs are on, but my headlights are really dim and "dispersed" is the best word I can use to describe. And they're not any better when I turn on my brights, maybe even worse. It appears that the deflector that focuses the light and switches from dims to brights isn't work. My headlights don't do the autoleveling when you first start up the jeep. HELP!! Does anyone know if/how to reset the deflector? I have AlfaOBD if there is a way to troubleshoot and/or reset. Thanks, Craig
@bearsgarage272
Жыл бұрын
I never would have figured out the tabs on my own. Glad I found this video before I damaged anything
@stagerman7431
Жыл бұрын
For others that had trouble finding the “tabs” locking mechanism, they’re attached to the car, not ON the bulb- felt that was a little unclear from this explanation. They’re about 1/2-1 inch each in diameter, so pretty noticeable if you feel around. You can see them a bit in this video- spent about an hour trying to feel for them until I saw this - then got it out easy. Good luck! kzitem.info/news/bejne/qKV6noZ3aqaemGk
@MAAT00
Жыл бұрын
I purchases a set of underground lighting Ds3s which seem to be some of the best ones but they came out of the install very Dim! Extremely dim! The high beams really aren’t that much better! I have a 2014 summit. The pair of headlights I purchased before were dim as well! Any ideas on what could be causing this? I’d hate to have the dealer install and pay 1200🥲. Please help
@80DeuceAdventures
Жыл бұрын
The best video I found!! Nice job man. I about torched the car in the process I was so frustrated!! Thank you Thank you!!
@gonzcg01
Жыл бұрын
Guys can you explain the tabs better. I was able to change the driver side with no issues. Its super easy to install it but for the life of me I cant get the passangers side bulb to rotate / engage. I am doing the same thing as with the driver seat
@beaumazzanti357
Жыл бұрын
HEY. had to do this same thing. Nowy blinker went out on it. Please tell me you have a vid for front driver side blinker lol thanks. Without having to take the front clip and bumper off thanks
@DrunknOdin
Жыл бұрын
Did you get your blinker fixed? If so how'd you do it? Mine just went out also and can't seem to find anything anywhere on how to replace.
@OmarAmaya138BPM
Жыл бұрын
Can anyone give me pointers on the following. I’ve removed all the components on the driver side but the bulb is stuck
@robertb285
Жыл бұрын
Does anyone know if this would be the same on a 2017 jeep grand Cherokee summit. Also what is the exact bulb to buy? Just any DS3
@albertpinedo6099
2 жыл бұрын
Do you have the Bi-Xenon light that turn with the steering wheel?
@dillonpaulson7574
Жыл бұрын
Yes, these turn when driving
@bollomcbollo6260
2 жыл бұрын
Very useful, thanks. My 2011 UK model had a similar arrangement, but with a little lever to lift up and down to release or secure the bulb
@JPeterman
2 жыл бұрын
I really wish there was a better video on how to set in the bulbs. I have tried eveything to get them to clip into place but they just fall out. I can't see into the hole so I don't understand how the bulbs clip in. I can feel the metal clips but I am not sure how they work.
@xXPrestianoXx11
Жыл бұрын
Did you ever figure this out? I am struggling a ton to get them back in place.
@realgrantdecker
Жыл бұрын
@@xXPrestianoXx11 was just doing mine last night twice bc I installed cheap aftermarket bulbs that ended up being worse. The small metal pieces form a square border around the headlight to hold it in place. I push in on the back of the headlight while rotating the plastic pieces to lock it in
Пікірлер