There's a hose on the bottom above the starter on the back of the intake manifold that has to be carefully disconnected or it will break during the final removal!
@jeddavies3635
7 ай бұрын
And the metal tube on the right side inside the manifold (pictured at the end of the video) has to come out using a 22mm or 7/8 wrench
@ahmadghosheh3104
8 ай бұрын
Stupid Ford.
@oldwrench579
9 ай бұрын
Why did you replace the PVC valve? What were the symptoms?
@hallvw
9 ай бұрын
Been awhile on this one. If I remember correctly, rough idle, lean codes. Ran it back to the hose had a crack in it causing a large vacuum leak. So replaced the assembly while it was apart.
@rafaelmartell7278
Жыл бұрын
Tendrás el vídeo donde se encuentra la válvula y la sustituyes?
@hallvw
Жыл бұрын
The PCV valve is on the back of the intake. It's right there where you can get to it when you take the intake out.
@crankshaft007
2 жыл бұрын
Thanks posting 4 cylinder, would have been nice to see intake out and next steps
@stankelly6431
2 жыл бұрын
thank you for your video. can you tell me where the MAP sensor is located on this very same engine. can't seem to see it want to attempt working on my own escape. can't afford a mechanic now. thanks.
@argoyle902
Жыл бұрын
I believe it’s in the air intake if you undo clips to air filter it should be right inside
@AC-gu7rg
2 жыл бұрын
Question, can you please tell me exactly where the pcv valve is located on that engine . Please and thank you
@hallvw
2 жыл бұрын
It's bolted to the backside of the intake. 22mm to remove the pipe sticking into the intake
@AC-gu7rg
2 жыл бұрын
@@hallvw I thank you very much for getting back to me , appreciate it !
@hallvw
2 жыл бұрын
You're welcome
@124marsh
2 жыл бұрын
Is there any other specialized tools you need besides the sockets. Thank You for making this video.
@hallvw
2 жыл бұрын
No nothing specialized. You're welcome
@chrisehresman8198
2 жыл бұрын
As a ford and chevy owner this video is making me want to sell the ford... thanks for the video!... now I know what my tomorrow looks like.😁
@CeeJay-pr5eg
2 жыл бұрын
Perfectly instructed, you did awesome, saved me so much time thank you very much for your guidance.
@bobl.2213
2 жыл бұрын
I was gonna remove the Starter to try to get to mine since the PVC is between the Starter and intake manifold. If that doesnt work this will.
@justlg3359
10 ай бұрын
Did it work?
@edwinporrata2666
2 жыл бұрын
Best way I seen to remove it,thanks so much
@darrinfaulkner8911
2 жыл бұрын
Thank you for the short but to the point tutorial.I just ordered a intake manifold today and have to do the same to my car shortly.
@tman8939
3 жыл бұрын
thanks for posting this, i have issues with my three point and will need to do this when fixed.
@hallvw
3 жыл бұрын
You're welcome. Just remember the lift arms will move randomly. Keep people clear of them for safety.
@mikegalloway3861
3 жыл бұрын
You did a great job sowing how this all goes together. I appreciate the already lose bolts, I don't need to see how to work a ratchet, LOL!
@hallvw
3 жыл бұрын
Thanks Mike
@richhalmuth160
3 жыл бұрын
Can you cut cast iron with it
@hallvw
3 жыл бұрын
Hello Rich. I haven't tried cast with it. I'll find some cast and try it. It should cut it but not sure how clean it would be with cast.
@BDauto86
3 жыл бұрын
I've had mine for about a year and it still works great. We use it alot with speed squares and a strait edge, you can make some really nice clean cuts very quickly.
@hallvw
3 жыл бұрын
I really like it so far. Can't beat it for the price
@jeremycole6873
3 жыл бұрын
Do you have to touch the tip to ark ?
@hallvw
3 жыл бұрын
Hey Jeremy. Yes you have to touch it to get an arc. This is not a pilot arc model
@BDauto86
3 жыл бұрын
Sometimes you have to touch but most of the time it takes off no problem.
@ramellin
4 жыл бұрын
Try to keep your right elbow tight to your side as much as you can it’ll help steady your cuts
@MurathanKosem2
4 жыл бұрын
Yapmayın sakkın
@mustafakebas7180
3 жыл бұрын
Bozuyormu ayarlari
@adventureswiththetwins2734
4 жыл бұрын
very helpful! i have a 08 ford escape 2.3 and i cannot get the water pump off i have removed 3 bolts holding it and have chipped peices of it and it has not budjed i was thinking taking the intake off and the thermostat housing to hit the water pump from behind do you know if waterpump can be hit with a pry bar from thermostat housing hole?
@hallvw
4 жыл бұрын
The pipe that's sticking out of the engine into the intake on the driver side is a 22mm to remove. The injector fuel rail is two 10mm bolts to remove. One bolt I forgot to show is a 13mm on the bottom of the intake, access it from underneath looking up at the intake
Пікірлер