Is this the same setup for the 2.5 as well? Same year.
@abcdefghei
3 ай бұрын
did the code was P0753
@AbdulBasit-df1vf
3 ай бұрын
Ford fusion Same engine Mercury Milan 2007 P2709 shift solenoid ss f electrical. Any Body knows explain . And location . Thank you please
@Mazenallaham
4 ай бұрын
Do you need to program the new TCM?
@kgarage-.-
5 ай бұрын
At the end I did the same test in another x tail, same result. Seem normal, but anyone can explain that pls?
@EliseiMiron
5 ай бұрын
How about the DSC light on? Wasn't related to the bad TCM? I have a similar issue (Lost Connection with ECM/PCM and TCM) with 3 lights on (Check Engine, AT, DSC).
@kgarage-.-
5 ай бұрын
What DTC code do you have? A bad TCM can trick the DTC and DSC at the same time.
@DelightSpencer_lover
5 ай бұрын
Hello, I just bought a 2011 Mazda 3, but I discovered that my car shakes whenever I put gear in Drive and Reverse. Scanning machine detects solenoid a,b,c electrical problem. Please what should I do?
@kgarage-.-
5 ай бұрын
Have you check the fluid condition? I had a case the solenoid electrical problem cause by a dirty filter.
@junerapana
7 ай бұрын
Was the problem the solenoid or the tcm with this car?
@kgarage-.-
6 ай бұрын
TCM
@clardiocasseus2299
8 ай бұрын
I have a 2009 Mazda 5 the problem I have is that: after starting the engine, I have to wait around twenty minutes so that I can roll forward
@kgarage-.-
6 ай бұрын
Any code was store?
@clardiocasseus2299
8 ай бұрын
You speak french , i have a question for you
@kgarage-.-
6 ай бұрын
I am all ears.😊
@gabrielmontero9172
8 ай бұрын
Valve body is the other one
@TingKWong
9 ай бұрын
Yeh, I did mine yesterday. On of the plug was a bit harder but still seem not worth $300 as a local shop quote me😅
@USADMIN
11 ай бұрын
I have a Mazda 5 2009. I have the same problem. I have changed Solenoid A & B electrical and TCM still car jerk in reverse gear and AT light s on.
@TingKWong
9 ай бұрын
My sis Mazda 5 has a same issue, turn out the gearbox have to overhaul.
@AnthonyLeal-uz2re
8 ай бұрын
Tcm
@thedanielescamilla
13 күн бұрын
@@AnthonyLeal-uz2rehe already did that
@macdonaldsmotorworks
Жыл бұрын
I agree with R side - gravy job ... L side front plug.. a bit harder but still "ok". L rear plug is a toughie. Have to remove the connector on the plug boot, space between the motor and body is super tight, AC lines and wiring harness to fuse block in the way. It's still doable - just did this job last week... but that single plug is way different than the other 3
@kgarage-.-
Жыл бұрын
Turn out it was the rod bearing...😅
@rakhilchirukandoth2482
2 жыл бұрын
Starter
@harrystacey7656
2 жыл бұрын
ik there’s no gas in it🤠
@kgarage-.-
2 жыл бұрын
Engine oil leave is OK, doesn't sound like a lifter noise and actually the camera unable to catch how loud is that. If any idea will be appreciate.
Пікірлер