Muito obrigado, eu tenho um tx nr626 que agora voltou a vida, eu moro no rio de janeiro Brasil.
@dihgdik
8 ай бұрын
Thank you, but it did not worked on my tx-nr414. I successfully switched it to HDMI ignore mode, and I hear third relay now, but there's still no sound. What else can be wrong with it?
@rebmaxdigilabs2161
9 ай бұрын
Will the tone control works when switching to analog mode? Is this short key working for all onkyo systems? Will this idea work on TX-SR 506..i dont have the equipment right now with me...someone pls reply. Thanks in advance 😊
@michalsedlacek4121
9 ай бұрын
Tone control / equalizer is embedded function of disabled DSP = no.
@dautyunesko6791
10 ай бұрын
Hei! Kan du hjelpe meg?
@eriksashov
11 ай бұрын
dzieki bardzo
@kisscreature74
Жыл бұрын
Thank you! I was almost ready to give up on my HT-RC270 after trying the chip heat and solder flow a couple times with no luck. Wish I saw this a couple years ago when my other receiver went out. I really hated losing it. Just make sure you have your speakers hooked up to the zone 2 terminals before trying this. I'm ok with not having surround and hdmi because mine was for stereo only setup. Thanks again!
@Bill-Rocker
Жыл бұрын
Thanks for posting. I would prefer any language to none. I can translate speech but deciphering is more difficult.
@Kpostma100
Жыл бұрын
i just got a consult 1 for very cheap,looks good but wont start up. battery voltage is 4.2 volts after about 45 minutes of charging. do you have an idea what the problem could be?
Жыл бұрын
link na tie led mozes sem dat ci je to tajne? Pripevnoval si ich lepenim?
@michalsedlacek4121
Жыл бұрын
Tajne to neni - link neni, led me z neceho zbyly jako vzorky po nejake vyrobe. Je to obecne vyrobce luxeon rebel - smd red, mely by byt k nalezeni v beznem kamennem maloobchode nebo Ali...
@erikt211
Жыл бұрын
Is there anywhere I can get more info on this device like an instruction manual? Or find info on the cards? I have a Consult 1 and am trying to learn it, thanks!
@jorgehenry208
Жыл бұрын
hola, y para hacer esto en un tx-sr707 como seria ,gracias
@jirkabinar2633
Жыл бұрын
Dobrý den/ ahoj... Děkuju moc za vaše video... Muj 515 ma stejny problém. Cetl jsem od vas pak článek kde to rozebirate detailněji ( myslim že v angličtině) ale uz ten článek nemůžu najit. Mohl byste prosim přiložit odkaz. Dekuju. Jirka
@michalsedlacek4121
Жыл бұрын
Dobry den, je to zde na webu t18.wz.cz/index.php?mainPage=audio/Onkyo_TX-NR515/TX-NR515_reballing_bga_rework/stred_onkyo_TX-NR515_reballing_bga_rework.html
@mattcero1
Жыл бұрын
FACTORY RESET for the receiver by pressing the CAB/SAT button then pressing the power button. FACTORY RESET the remote by pressing the receiver button and home button until the red light stays lit, and then pressing the receiver button to extinguish,,,FYI.
@mattcero1
Жыл бұрын
HELP PLEASE! My white volume rocker is unresponsive on my remote so I used the unit volume knob for this. I can get sound with AM and FM radio but no sound via any HDMI source even though I get video. I even did a factory reset pressing the CAB/SAT button then power procedure and the factory reset didn't solve the silent HDMI sources. Can anyone provide me with some assistance? It's such a nice piece of gear to be unusable. Thank you.
@moun10high
Жыл бұрын
Hi. I can't get the 3rd relay to click. I did as shown on video. I also tried to heat the dsp circuit. Didn't help.
@moun10high
Жыл бұрын
I got the TX-NR609
@michalsedlacek4121
Жыл бұрын
@Epic-Ape Hello, and in your case - do you hawe switched receiver to analog mode ? Showed display message "HDMI INGORE" ?
@jackie7239
Жыл бұрын
This method works 100 % just did my 609 now plays via the analog cables . Plug main speakers hold power button and br/dvd button keep holding power till hdmi ignore apears them press power to diable hdmi . Ill advise u hv something connected to analog rca jacks either cd player or something have it playing tap on the source to cd ...
@Honzulak77
2 жыл бұрын
More info about LED SMD type?
@michalsedlacek4121
2 жыл бұрын
Luxeon Rebel SMD family Lumileds
@luisparry3344
2 жыл бұрын
it is necessary to have the remote control, since I did the procedure with a tx nr709 and if the relay is heard but it does not give audio
@michalsedlacek4121
2 жыл бұрын
You dont need IR remote control. Only switch Onkyo to hdmi ignore mode and select analog input like FM radio or CD aux. Connect speaker only to front L and R power output. If relay click and you dont still have sound, try contact experienced electro audio eng and try connect low audio signal direct to power amp board... Maybe you have another fault like amp power source relay.
@jonathandiaz6046
2 жыл бұрын
Hi, works for tx sr608? No have sound in any channel analog or digital =(
@rickygonzalez1545
2 жыл бұрын
what is KISS analog source? FM radio channel?
@michalsedlacek4121
2 жыл бұрын
Yes, FM station from Brno - www.kiss.cz/
@ulrichzache3793
2 жыл бұрын
Thank you so much Michal! As many others I am happy as can be to hear the full stereo radio sound of my old friend again. What could be the reason that I have no sound from the analog inputs? Thanks for any idea, Ulrich from Germany
@gabrielmaurelli8573
2 жыл бұрын
Could it work even with my Onkyo TX509?
@michalsedlacek4121
2 жыл бұрын
Try it...
@grinpink31
2 жыл бұрын
What about HDMI BD : DSPTH ?
@ramdanzulfikarsopiandi7012
2 жыл бұрын
where you get this device?
@michalsedlacek4121
2 жыл бұрын
I obtain them as inoperable, but only internal battery was discharged and next was needed load program to device as is described in video. But i dont have a probe cable for measuring voltage and signal... Look for ebay, allegro and other markets, sometimes is for sale.
@robindavies5579
2 жыл бұрын
This is a really frustrating video. Even with the subtitles on it is extremely difficult to understand what you are doing and why.
@ponukypanacea7330
2 жыл бұрын
Úžasná pomoc Michal. Už nám z toho v práci na predajni hrabalo. Raz to išlo, raz nie. Problém sme vďaka Vám vyriešili. Dali sme aj továrenský reštart. Neviete náhodou ako sa dá vypnúť "auto standby"? Prešli sme manuál na nete, ale nič sme nenašli. Ďakujeme
@michalsedlacek4121
2 жыл бұрын
Zdar na Slovensko, autostandby najdete normalne v menu na displeji... Mate moznost jej nastavit cas nebo vypnout uplne. Proklikejte to a najdete to.
@LEEG337
3 жыл бұрын
Damn, I have been struggling for ages trying to figure out what the hell was going on with my receiver. Thanks for this fix!
@michalsedlacek4121
3 жыл бұрын
Hi, for more information visit with EN translator webpage: t18.wz.cz/index.php?mainPage=audio/Onkyo_TX-NR515/TX-NR515_rebuilding_to_analog_amplifier/stred_onkyo_TX-NR515_rebuilding_to_analog_amplifier.html
@ahmadefendi561
3 жыл бұрын
How to get back out of this analog button..
@michalsedlacek4121
3 жыл бұрын
If you want go back to digital mode you only repeate the same steps... Described steps switch buetween two modes - digital (over DSP smached chip) or analog (analog multiplexer switches which are in front of DSP input switch anlog signal not to DPS inputd but direct to analog power amp. - so DSP is unused).
@ahmadefendi561
3 жыл бұрын
can you connect the cellphone to the tv/CD socket using an rca Jack cable from the cellphone to the CD/tv ..socket
@michalsedlacek4121
3 жыл бұрын
no problem - all analog inputs like RCA are welcome (inputs like HDMI sound or IR digital are over DSP ant this is off); look on schematic (very clear picture) on my website www.t18.wz.cz over google translator - t18.wz.cz/index.php?mainPage=audio/Onkyo_TX-NR515/TX-NR515_rebuilding_to_analog_amplifier/stred_onkyo_TX-NR515_rebuilding_to_analog_amplifier.html
@nitantson
3 жыл бұрын
This worked on my Onkyo 609. Thanks a lot Michal. This fix is AMAZING!!
@eliasmetal07
3 жыл бұрын
It is Works for me
@just_kill
3 жыл бұрын
Nice.. Thank you so much. This receiver has been shelved for a few years now and now I can get some use from it again. :D
@pavilionkakrinski9425
3 жыл бұрын
Thanks a lot for the video. It turns out. Can you tell me how long it works after this reboot.
@michalsedlacek4121
3 жыл бұрын
How long... Wrong question - board is switched only to pure analog mode - analog digital controlled switches only switch analog input direct to analog power amp board - its second operation mode LOOK ON RECEIVER SCHEMATIC; so "so long" as silicone elements will be work... ;D ... btw I own one of Texas Instruments laptop from 93" and with 4MB ram is still working. This isnt reboot this is another operation mode.
@hobbymakemyhappyp7709
3 жыл бұрын
Working thanks!
@rickfreeman226
3 жыл бұрын
I wish I understand stood, the step by step procedure here! Words would be great! Said or written please help thank you
@michalsedlacek4121
3 жыл бұрын
Hi, this is not procedure... Switch subtitle on, conteins all...
@michelaraujo6923
3 жыл бұрын
I would like to thank you wholeheartedly, my 515 worked, I'm from Brazil and I had difficulty understanding the video, but a link here in the comments also guided me, eases our frustration of having such an expensive and powerful receiver unused, this video is the best of all for at least it gives us a happiness to make the analog outputs work, thank you very much!
@michalsedlacek4121
3 жыл бұрын
Thx, but now you have only 2 channels functional - is possible reconnect analog signal on main amp board to all power amp and use damaged Onkyo like "multi room" audio amp.
@Joneco
2 жыл бұрын
Cara pode explicar oq fez? O video ta mt mal explicado. Tenho um ht rc 360
@mattcero1
Жыл бұрын
@@michalsedlacek4121 HELP PLEASE! My white volume rocker is unresponsive on my remote so I used the unit volume knob for this. I can get sound with AM and FM radio but no sound via any HDMI source even though I get video. I even did a factory reset pressing the CAB/SAT button then power procedure and the factory reset didn't solve the silent HDMI sources. Can anyone provide me with some assistance? It's such a nice piece of gear to be unusable. Thank you.
@carstencroessmann
3 жыл бұрын
Hi great task. Do you know which card is for Nissan Maxima QX A32 from 1994? What do you think about the consult to USB devices? Thanks for answer Carsten
@michalsedlacek4121
2 жыл бұрын
I think that for A32 is better way Nissan Consult II. Sorry for my reply after ten months.
@carstencroessmann
2 жыл бұрын
@@michalsedlacek4121 Better than never. Where are you from? Greetings Carsten
@Travis141123
3 жыл бұрын
Worked on my 809.
@michaelthorrold7045
3 жыл бұрын
Thanks so much. I have a 609 and 709 which both have the HDMI audio problem. I was ready to throw them both out after trying many workarounds. I saw your video just in time and they are both working in 2ch now, with hdmi switching for the video. On the 709 I even managed to drive all channels with neo:6 or PLII. Thanks again!
@michalsedlacek4121
3 жыл бұрын
Hi, check my website - use google translate... 1. www.t18.wz.cz/index.php?mainPage=audio/Onkyo_TX-NR515/TX-NR515_reballing_bga_rework/stred_onkyo_TX-NR515_reballing_bga_rework.html 2. rebuild www.t18.wz.cz/index.php?mainPage=audio/Onkyo_TX-NR515/TX-NR515_rebuilding_to_analog_amplifier/stred_onkyo_TX-NR515_rebuilding_to_analog_amplifier.html
@michelaraujo6923
3 жыл бұрын
I would like to thank you wholeheartedly, my 515 worked, I'm from Brazil and I had difficulty understanding the video, but a link here in the comments also guided me, eases our frustration of having such an expensive and powerful receiver unused, this video is the best of all for at least it gives us a happiness to make the analog outputs work, thank you very much!
@souljeune
Жыл бұрын
@@michelaraujo6923 Eu acabei de comprar um com esse problema, espero que eu consiga arrumar.
@ctiffo1972
3 жыл бұрын
Sound that mate .... Some sound is better than nothing at all very clever you found this on the 616 model its bd/dvd and power button
@SuperHddf
3 жыл бұрын
You are a god sir
@michalsedlacek4121
3 жыл бұрын
Procedure is step by step described in subtitles.
@jaguardelsol17
4 жыл бұрын
Dude it would help if you say somefhingvand explain what upure doing!
Пікірлер