Great information straight to the point, I hope this works for my 2013 Qx56
@ricardovillanueva825
2 ай бұрын
Thank you very much will try.
@yoashuain1
4 ай бұрын
Bill? Is this you?
@DaleNolan
9 ай бұрын
Thank you brotherman I’m going to do my 07 HHR and see if it will fix my issues. My traction control pops off and car will shut down for a few minutes then cranks up and runs?? It’s putting a code P0016 and P0017 all sensors are new also
@JAMESJJEFFERS
9 ай бұрын
Keep it Old School Brother 💪💙 Love My Titan
@ChangedUpNowWhat
9 ай бұрын
Thank you! Question, can you use any wire around the house and cut the tips in order to wire it? Or does it specifically have to be a ground wire for a car?
@txwarrior66
7 ай бұрын
I have found over the years pretty much any wired would work I tried to use automotive wire but yes I have even seen an old extension cord used when they didn't have anything
@marcmercado2085
Жыл бұрын
Cool. So you’re a parts changer. No diagnostic process that led you to the sensor. In your case it fixed it, but sensors aren’t always the problem.
@docholliday4388
Жыл бұрын
How about the led warning panel, won't light up.
@tgrimes750
Жыл бұрын
Straigh to the point...thankyou Sir!!
@brandonburch9703
Жыл бұрын
This grounding did help but it was one of 3 things I had to do, for.the ones saying this didnt help possibly check your vapor canister, vent solenoid.. was causing guages to jump around weird shifting..
@davidraichel7554
2 жыл бұрын
Had the exact same problem but this ‘fix’ did not help at all.
@davidraichel7554
2 жыл бұрын
This process did not work at all
@perryjeffery6116
2 жыл бұрын
I tried the ground wire but it didn't work
@nicestrat
2 жыл бұрын
I'll have to try this. Thanks for the upload!
@charlesgammons8368
2 жыл бұрын
I cannot thank you enough for sharing this video. It saved my family well over $700 for repairs the dealership tried to convince me that it needed. Again, thank you 🙏🏾.
@quintusbristo3913
3 жыл бұрын
You rock buddy thanks You rock thanks I have a QX56 with the same problem your video DIY problem fixed it and I saved a ton of cash buddy.
@jonathandoleman8008
3 жыл бұрын
"petal to the floow"😂
@jeremiahlove4200
3 жыл бұрын
Really appreciate you putting this video up, just replaced my passenger front caliper and needed some help so good to go now!!! Thanks again for the video
@Gleeleeglee
3 жыл бұрын
I am planning to replace the front passenger (front right) as well and after replacing it did you bleed this caliper or did you bleed the rear right side first?
@Gleeleeglee
3 жыл бұрын
Also the factory service manual for a 05 Titan says to bleed in order rear right, front left, rear left and, front right.
@galint-town8034
3 жыл бұрын
Thank you!! Spent just over $2500 over the last year and still having trouble. Hope it will fix this 2011 beast.
@QueensJack
3 жыл бұрын
Nice find and thanks for the information shared.
@questioneverything3332
3 жыл бұрын
No reason to shoot that brake fluid all over the floor. A simple pale or bucket catches it
@chadmangum4158
4 жыл бұрын
How about some actual instructions? "Have the guy in the truck pump the brakes a few times and then hold it to the floor. While he's holding it to the floor, then bleed the brakes, close the valve, repeat." You kind of glossed over some of the important info there.
Пікірлер