Nice job. What type of vinyl did you use? Allsport? Or just standard 30 oz marune vinyl. I have a 3 seater GTI seadoo with some sharp contuors that will need something stretchy
@1979augistine
7 ай бұрын
360 degree stretch is what you need
@samsterhaus4523
2 жыл бұрын
Where do you buy the strap? I’m reupholstering my seat
@infinitestitchesupholstery4794
2 жыл бұрын
They are usually just 1" nylon webbing covered with vinyl. I remove the old and glue on the new.
@samsterhaus4523
2 жыл бұрын
Thank you so much I’ve been trying to find something for a while now
@samsterhaus4523
2 жыл бұрын
Any place you recommend buying from?
@infinitestitchesupholstery4794
2 жыл бұрын
@@samsterhaus4523 honestly, I'm not sure. I purchase it from my suppliers, but they only sell to businesses. Check Amazon, i think I've seen it there before.
@samsterhaus4523
2 жыл бұрын
Ok thanks
@evanheffley1625
2 жыл бұрын
Great tutorial, only question not answered for me is what product to use to fill in any deeper defects in the foam. I have a few spots that pulled out a bit of foam cause I didn't know to use a hair dryer. I have the same seat that seadoo glued the cover on the foam (GSX)
@infinitestitchesupholstery4794
2 жыл бұрын
I hope that I was able to help you over the phone. I'll be sure to make a video on next one I get in, that requires foam repair.
@evanheffley1625
2 жыл бұрын
@@infinitestitchesupholstery4794 Awesome, thank you again for offering you expertise!
@justdoit8613
2 жыл бұрын
Great job thank you.
@ItsMista_2u
2 жыл бұрын
🔥🔥🔥 whats the price range for something like this?
@cringes_sucks_at_life
3 жыл бұрын
What type of glue is in the spray gun?
@infinitestitchesupholstery4794
3 жыл бұрын
DAP Weldwood
@elmeradams8781
2 жыл бұрын
What spray gun? How do you keep it from plugging up the spray gun?
@infinitestitchesupholstery4794
2 жыл бұрын
I use a siphon feed paint gun. As long as you keep the cup full of fresh glue, you shouldn't have an issue. Occasionally I'll have to clean the tip with lacquer thinner.
@FIREBALLJR2001
3 жыл бұрын
Great job. Thanks for sharing.
@jairogonzalez6536
3 жыл бұрын
Awesome work buddy. thank you very much for sharing.....It is too expensive to get a cover from HT or blacktip... they are nice but $ 200.00 each. I hope to be able to do my 2 Honda aquatrax following your video. Thanks.
@thadioushorowitz4210
3 жыл бұрын
Saw this video AFTER I just did mine today. I left the old cover on because it was glued on. If I saw this first, I would have known how to take it off. At least the vynil was inexpensive. I can recover it again at the end of the season. Great video! I have a few more puckers inside the staples than you have. I'll do better next time. Thanks again!
@logansteele639
3 жыл бұрын
What is the price to do a two piece seat?
@Jayjay610_
3 жыл бұрын
Whats the pink stuff? Extra cushion?
@infinitestitchesupholstery4794
3 жыл бұрын
It's 1/4" sew foam. It is used to smooth out the original foam after removing the old vinyl.
@Jayjay610_
3 жыл бұрын
@@infinitestitchesupholstery4794 awesome! Thanks for the info!
Пікірлер