Take the coolant reservoir out of the way. Quick change.
@Mareyon901
8 ай бұрын
THANK YOU for your video… It works. A couple Snatches but it worked. Took about 1 hour for both lights.
@paveltantsiura
8 ай бұрын
This was not easy at all, but I did it. Took 40 min and scratched my hands. Be careful when you test the new lamp not put it in the plastic since it gets hot in seconds. I did it and it melted some plastic almost caused fire 😅 Also when you move your fender you will have to align it with the hood.
@dylanjackson6107
8 ай бұрын
Nooooo it is notttt that easy tried it still can’t
@shemacferguson6190
9 ай бұрын
Is it the same for the driver's side?
@rickriber1459
7 ай бұрын
NO!!!!
@t39gamer
11 ай бұрын
You can pull forward on the headlights, you might break the bracket. on the bottom of the headlight.
@t39gamer
11 ай бұрын
Does not work with all ford fusion
@frankmontez6853
11 ай бұрын
So you twist down and it pops out? No need to turn bulb connector counter clockwise or the other way ?
@nankau808nanakuliea3
11 ай бұрын
Thank you so much for this video. I'm so frickn happy that I found this video. Other videos did not mention of pressing a button down. Once I found that button it was so easy. Had I not found this video I would have given up and payed $220 bucks just for a $12.00 bulb. 🤗🤙💯
@Thaluvpoet1
11 ай бұрын
Show it.. show how you did it exactly. Saying it is not working when tried
@07dodgeman68
Жыл бұрын
Thank you so much it was so much easier I give you 50 thumbs up 👍
@edwardhunt6255
Жыл бұрын
No, you didn't. You just say that you did
@j0cr0z
Жыл бұрын
that’s one side dip shit, what about the drivers side. you PoS
@MrShadow5556
Жыл бұрын
It'll scratch your paint won't it?
@marcusellis3044
Жыл бұрын
It doesn’t even work 😂 you’ll have an extra 1cm if you take off your bolt from the fender 🧐 then it starts to bent and crease your front fender… smart man for lazy work
@errolikalina1998
Жыл бұрын
@@marcusellis3044 It actually does, I did it with my daughter's Fusion. It gives you just enough room to get at the connection but requires a lot of dexterity with your hand. took me short of 30mins.
@errolikalina1998
Жыл бұрын
No it won't, it didn't when I replaced my daughter's lights.
@williamruiz8927
10 ай бұрын
If u try, maybe u can slide a piece of card board under the light housing.
@Bighustle21
Жыл бұрын
Thanks for sharing this you saved me a lot of headache.
@frankellard9126
Жыл бұрын
It won't "just pop out" !!🤬🤬
@DeafeningSounds
Жыл бұрын
US spec lights must be different to UK ones as with all that undo the light comes forward but the getting the bulb out without the clip coming off is a miracle! Removing half then bumper is way quicker and best to swap in LED lights!
@t39gamer
11 ай бұрын
You're right about that. Headlights Has a bracket Boulder to the bottom of it.
@ExGLifeStyle
Жыл бұрын
Bro what way am I turning
@errolikalina1998
Жыл бұрын
So you turn it clockwise if you're facing the car (which you will most likely be). Turn it counter-clockwise to screw it back in. What I found most difficult is getting it in the notches before you can turn and lock it in since you can't see what you're doing. Just look at the three tabs on the light fixture and look at the notches in the headlight assembly to see roughly what orientation they light fixture should be in to get it in thenotches so you can lock it in.
@jhipstyle77able
Жыл бұрын
Thank you for this video! Super easy!
@joepaul1763
Жыл бұрын
Thank you! The recommended way by taking off the entire front end of the car to change bulbs is absolutely idiotic
@bobomomo3764
Жыл бұрын
Have u guys tried this method and how easy was it?
@ariass9345
Жыл бұрын
@@bobomomo3764 I wanna know too! Lmk if you did it
@errolikalina1998
Жыл бұрын
@@bobomomo3764 The most difficult part is actually turning the light fixture to remove it and putting it back.
Пікірлер