What about the bottom cup? I could not spot it in the video.
@roberterickson5817
9 ай бұрын
Great video! What's the white grease you applied to the wiper seals before putting the stanchions back in? Thanks!
@mountainbikeservice155
9 ай бұрын
Renolit SL 410 M silicone grease
@michaelbauza8315
9 ай бұрын
Maybe a good service instruction but where to get which parts and tools???
@_BlueHorseshoe_
9 ай бұрын
My son just did this service but forgot to put the grease on the inside of the seal. Is is possible to wipe some on the stanchion and work it back and forth to get sufficient grease in there without redoing the entire service? Thanks.
@mountainbikeservice155
9 ай бұрын
No, a seal is meant to keep things out. If what you say could work, then a couple of wet rides and your fork would be filled with water and grime.
@Ddigzdirt
10 ай бұрын
amazing tutorial👍 today I learned why I go to the shop😂 I dont have near enough of a tool collection to attempt this. Yet.
@TheProjectX3
Жыл бұрын
Isn't it full service? And after assembly, you should start with 20 or so psi then equalise it with the negative chamber and work towards desired preassure
@VvvnimaL
11 ай бұрын
Yes and yes
@zdravo4
Жыл бұрын
Very good video with great explanation. I have the same Reba and I am thinking of service, but I will leave it to pros to do that, of course with service set for my fork.
@hokiedokie
Жыл бұрын
Thanks so much... these forks are great for what they are.
@KEENY475
Жыл бұрын
just a very good clear video surprised by lack of views
@belialheathers897
Жыл бұрын
My Reba has stiction problem, what do you think is wrong with this.? I just serviced it still has the same issues
@simonchaddock3694
2 жыл бұрын
Can you do one with fit4 damper cheers
@edt5276
2 жыл бұрын
Good effort put into video but not great results. Poor camera work. Narration is not synced well with what's happening on screen. What is the difference between green socket you used and a "regular" socket? This service is not too complicated for a 1st timer. This video might be a good refresher for someone that's already done service on other shocks, but this video is not a good tutorial for a 1st timer.
@garyg2
Жыл бұрын
he showed the bottom of the socket. it's totally flat, so it can grab the shallow top cap that's only a few mm tall. most sockets are curved for a couple mm on the end and that might prevent the socket from being able to grab onto the top cap. even if it does work, it could damage the cap. you could just grind down an existing socket so it's flat on the end. there's also a variety of top cap wrenches in various styles available online
@harryking8498
9 ай бұрын
The green socket is machined flush. A typical socket is forged, and has a slight "ramp" from the lip to the hex (or more commonly 12 point) recess for the nut/bolt head. Since the hex portion of the cap is so small, there is a chance it will round if you use a more typical socket. If you have a good wrench like a Wrightgrip, you can break it loose with that, then use a normal socket. Or you can buy a cheap socket, and grind down the lip to make it flush.
@shallenmccarthy3961
6 ай бұрын
Yep, grab a typical socket, place sandpaper on flat surface, and sand away. Takes 15min or so.@@harryking8498
@edarnold99017
2 жыл бұрын
Nice instruction
@macvette1
2 жыл бұрын
Never work on the fork before releasing the pressure on the top!!!
@mtbmj7816
2 жыл бұрын
This step should be added.
@mtnmnkymilitia
Жыл бұрын
Blahahaaaaa🤣
@gunny6517
2 жыл бұрын
Absolutely the BEST Reba Service Video on KZitem…. New Subscriber, Thank You…. 🇺🇸
@mountainbikeservice155
2 жыл бұрын
Thanks and welcome
@vuss2107
2 жыл бұрын
Great video Awesome workstands Correct tool makes life much easier 👍
Пікірлер